Search Documents

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By J. C. Fowler

[This i.untra t hds bmii III c'IIILt fur till- past 1':?:u yrlr;, Till-- wurir pnrfor rw:it '. ,JS hlui.rn dawn Ilttf lit Iu i eel i ih?IS( S. 1 hesrt aIII, Phase I Candor tlri I a lest It) donurnSlrale SeiSrrlir nurihudS to hu USi!d lot ttlr? rti?tei thin and Iu" ainnl ul trapped rrlinc:rs hitting (-)it the roof with a harnrner, Phase I' Design and cunStrur.t a permanent Seismic monitor System to rrlunrtur roof (ails arm r:xploslun', III ,r 'Vol king mine. Phase III - Ire dII an an i i irr for sVstl rtl Ii i`'Smltur air quality in till, niitii iiH II ? ir,iti tin; niln !III ;I I ,, i; Phase I V - Conduct 11(21 d tests of the seismic IT IUnit UT ieq system fur a period nl two 11IUIIIIIS. Phase, V - Condirct three test periods of the seismic system over a period of six mimilis. Detailed reports covering the wurk. done in Phases I, 11, and IV have been i : . r tr I - i t report will, therefore, cuni.entrate on the work perfurmed in Phases III anti V.]

Jan 1, 1975

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962

By Kenneth M. Maas

The Bureau of Mines inventoried all lands in Alaska to determine the availability of land for oil, gas, and coal leasing. Acreage for onshore oil, gas, and coal basins was digitized as was land ownership data. Regulatory policy concerning oil, gas, and coal leasing for various government agencies and private concerns was determined. Oil and gas basins underlie 79.4 million acres of Alaska's 378 million acre landbase. Federal agencies manage 44 million of these acres. The Bureau of Land Management is the lead agency for most oil and gas leasing on Federal lands. Lands have to be specifically opened for oil and gas leasing to be available. The state of Alaska manages 21.1 million acres underlain by these basins. More than 80 percent of this acreage is available for resource development. Native corporations manage the remaining 14.3 million acres of favorable oil and gas land. Coal basins underlie nearly 51 million acres of Alaska. Of this land, 26.4 million acres are under Federal jurisdiction. The state manages 17.3 million acres of land underlain by coal basins. Nearly 7.3 million acres of favorable coal lands are managed by Native corporations.

Jan 1, 1991

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By J. M. Kuchta

Bench-scale test methods were developed by the Bureau of Mines for use by the Department of Transportation in the classification of solid and liquid oxidizers. A burning rate test is recommended for evaluating the fire hazard of solid inorganic oxidizers when mixed with a red oak sawdust as the reference combustible. A spontaneous ignition test is proposed for evaluating liquid and solid inorganic oxidizers which may decompose violently or ignite spontaneously when unmixed or mixed with the wood sawdust under unconfined conditions. Test results are compared for various representative oxidizers and a classification system is proposed for use in the government transportation regulations.

Jan 1, 1972

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By Richard A. Dick

Underground blasting in permanently frozen gravel was studied in a 7-by 12-ft drift by running a nonreplicated 2 X 2 X 2 factorial experiment on the effects of type of cut, delay, and explosive on the fragmentation subsystem. Comparisons were made between a V-cut round and a burn-cut round, millisecond delays and half-second delays, and 40 percent special gelatin and 60 percent high-density ammonia dynamite. The number of large blocks in the muck pile) loading time, shuttle car operating time lost because of cleanup needs, length of advance per round, and length of muck pile were recorded and statistically analyzed. None of the blast parameters had a significant effect on the length of advance or length of muck pile, although the half-second delays tended to give a shorter muck pile than millisecond delays. The burn cut required less secondary breakage, less loading and cleanup time, and gave better overall fragmentation than the V-cut. The ammonia dynamite shots required less secondary breakage and less loading time than those using special gelatin. The half-second delays gave better overall fragmentation and required less cleanup time, but the millisecond delays gave a better loading rate. None of the differences between delays and explosives were notably significant.

Jan 1, 1970

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968