Search Documents

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

By John T. Dieckmann

This report documents the work performed and the results obtained in a 2-year development of a Mobile Inert Gas Generator for use in the Bureau of Mines Remote Sealing System for fighting underground coal mine fires. The performance requirements of an inert gas generating system for the Remote Sealing System were clearly established. A thorough review of seven possible system designs meeting these requirements was conducted. An air cooled, distillate oil fired combustion type inert gas generator was selected for further detailed design, hardware fabrication, and performance testing. The Inert Gas Generator constructed under this program has been thoroughly performance tested and has been operated in the field for approximately 200 hours. The system has met or exceeded all important performance requirements. The system was used in the fire fighting efforts at the Bethlehem Mines Corporation Cambria Division Mine 33 fire and contributed to the successful containment of the fire. The system was also employed in the demonstration of entire Remote Mine Sealing System at the Jenney Mine in the fall of 1978. The system is currently avail-able for fighting any future underground coal mine fires.

Jan 1, 1979

Laboratory tests were conducted by the U.S. Bureau of Mines to determine respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Increases in exhausting face ventilation from 3,000 to 9,000 cfm, in waterflow from 15 to 35 gpm, and in water nozzle operating pressure from 80 to 200 psi were evaluated. Results indicated that airflow had the greatest individual impact on reducing dust levels, with concentrations at return and operator sampling locations reduced by as much as 57% and 99%, respectively. Regression modeling was utilized to predict dust concentrations over the range of values tested for the control parameters. Interactions between the control parameters were significant and often defined an optimum level where further increases in that parameter failed to produce additional dust reductions. Increasing airflow to 8,400 cfm, waterflow to 25 gpm, and water pressure to 140 psi typically reduced dust concentrations at operator and return locations. Application of a control parameter above these levels can provide additional dust reductions if used in conjunction with appropriate levels of the other two control parameters. Otherwise, higher operator dust levels may result and can be attributed to increased rollback and/or airflow turbulence.

Jan 1, 2010

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals-were reported, several years ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, Particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

By R. R. Hornor, Geo. M. Hunt

The purpose of this paper is to point out some of the benefits and economies to be derived by the better selection , preparation, storage , preservation and utilization of mine timber , and to give some specific information on certain wood preservatives and processes suitable for mine timber preservation . The paper is based largely upon data obtained by actual experimentation and service tests conducted by the U. S. Forest Products Laboratory , Madison, Wisconsin, on wood preservation , covering a period of many years , and upon a field survey during the past summer by one of the mining engineers of the U. S. Bureau of Mines of some of the principal mining districts of Michigan , South Dakota , Montana , and Idaho , in which he made a general ' study of mine timber in metal mines , particular attention "being given to timber decay ; the conditions under which it takes place most actively ; the measures , if any , that are being used to combat it; and, finally, the advantages that might be anticipated in the use of chemically treated timber to prevent decay and thus prolong its life .

Feb 1, 1922

By D. G. Leddy, J. B. Johnson, L. D. Gratz, S. T. Bagley

"Studies have been conducted at Michigan Technological University (MTU) for over twenty years on methods for characterizing and controlling particulate emissions from heavy-duty diesel engines and die resulting effects on regulated and unregulated emissions. During that time, control technologies have developed in response to more stringent EPA standards for diesel emissions. This paper is a review of: 1) modem emission control technologies, 2) emissions sampling and chemical, physical and biological characterization methods and 3) summary results from recent studies conducted al MTU on heavy-duty diesel engines with a trap and an oxidation catalytic converter (OCC) operated on three different fuels. Control technology developments discussed are particulate traps, catalysts, advances in engine design, the application of exhaust gas recirculation (EGR) and modifications of fuel formulations. Methods for dilution tunnel sampling, particle size analysis, chemical analysis with emphasis on polynuclear aromatic hydrocarbons (PAH) and nitro-PAH, and biological characterization using mutagenic activity (Ames) assays are described, along with statistical approaches to experimental design and data analysis.In studies at MTU, both particulate traps and an OCC have been shown to be effective for the reduction of total particulate mauer (TPM), with the OCC being better al reducing all forms of hydrocarbon emissions, including PAH and nitro-PAH, and with the traps being better at removing the solids (SOL). The use of low sulfur fuel (0.Ql % by mass) has led to additional reductions in TPM; the low sulfur fuel has been shown to reduce the number of small, nuclei-mode particles for one of the engines tested. PAH, nitro-PAH, and mutagenic actively levels generally decreased with use of either the traps or the OCC.INTRODUCTIONDuring the 1980s and the early 1990s there have been significant advancements in the development of technology to control diesel particulate emissions. Efforts have been focused on internal control of the engine by design, the use of after-treatment devices, and improvements in fuel formulations to reduce all the diesel emissions. The research and development activities have been driven by the need to meet the US EPA heavy-duty vehicle standards shown in Table 1. The important standards for new technology are the 1994 heavy-duty vehicle 0.1 gm/bhp-hr particulate, the new urban bus 0.05 gm/bhp-hr particulate standard for 1996 and the heavy-duty vehicle 4.0 gm/bhp-hr NOx standard for 1998."

Dec 1, 1995

By P. L. Woolf

Two blast furnaces, one a. commercial furnace and the other the Bureau of Mines experimental furnace, were successfully operated with extremely low slag volumes. The lowest slag rate obtained on the industrial furnace was 335 pounds per ton of metal. Using the same burden materials a 245-pound slag volume was achieved on the furnace. The coke rate saving and increase in productivity resulting from lowered slag rates are discussed as well as the factors limiting a low slag practice.

Jan 1, 1965

By Frank C. Andreuzzi

The Division of Environmental Activities, U.S. Bureau of Mines, conducted a solid waste demonstration project on a burning coal refuse bank. The primary objective of this project was to develop and evaluate an efficient method of extinguishing burning coal refuse and moving it. A series of tests were performed using water monitors and related apparatus to quench the burning material and, at the same time, using earth-moving equipment to transport, spread, and compact the extinguished material. The method found to be most effective consisted of water-quenching the surface material to a workable depth, ripping, and removing the quenched material with a bulldozer and tractor-scraper. The total cost was estimated to be $0.44 per cubic yard.

Jan 1, 1970

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By J. Howard Bird

The purpose of this publication is to describe the power-distribution system of the mine and refinery of the Duval Sulphur & Potash Company at Carlsbad, N. Mex. This distribution system has been excellently predesigned to meet requirements and fit special conditions encountered at the property. In presenting the material, the authors point out various features that would be desirable for incorporation in other systems under similar conditions. Central location of switchgear in pressurized vaults and ventilation of such equipment with filtered air prevent salt accumulations and contribute to trouble-free operation. The simplification of power-distribution circuits and overload protection, as a result of centralization of switchgear, the use of individual control circuits enclosed in conduit (which aids troubleshooting), and central location of control panels, are factors which contribute to efficient, safe operation. Those features are applicable to many operations where fire or explosion hazards are encountered, or where dusty conditions may exist, as well as in operations where numerous individual drives are involved.

Jan 1, 1959

By Charles L. Ross

A successful placer mine is being operated by the E. T. Fisher Co. on Rock Creek in the South Pass mining district at Atlantic City, Wyo. About 2,800 cubic yards of gravel is dug daily by a gasoline-driven dragline shovel with a 1 1/4-yard bucket and washed in a movable plant with a gold-dredge trommel and standard-dredge sluice boxes; the total cost is about 12 cents per cubic yard. The gold-bearing gravel occupies a narrow valley between two low ranges, of hills. The ground is covered by brush and willows, which are cleared of in the fall by burning after the leaves have dried. The elevation at the mine is 7,600 feet above sea level.

Jan 1, 1935

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964