Search Documents

By H. D. Jacobs

The Bureau of Mines undertook a research program to insure an adequate supply of iron raw materials for future iron and steel making needs. A sample was obtained of oxidized taconite from the western Mesabi Range in Minnesota, and the metallurgical response of the taconite to beneficiation by a process that included selective flocculation-desliming-cationic flotation was evaluated. The sample contained 35.3 pct iron and represented approximately 2 billion tons of crude material. Selective flocculation and flotation were evaluated in a pilot plant with a feed rate of 900 Ib/hr. Concentrates averaging 61.7 pet iron and 5.1 pet silica were obtained, with an accompanying iron recovery of 67.2 pet. About 83 pct of the process water requirements were reclaimed from the slime and froth tailing and then recycled.

Jan 1, 1980

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By E. C. Lane

The motor gasoline that is bring marketed in the United States this stunner is slightly more volatile than that sold a year ago. During the past eight years the Bureau of Mines has made semi-annual surveys of the gaoline marketed in the United States, the survey just completed being the sixteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By Charles L. Kimbell

Virtually every available measure of total world mineral industry activity demonstrated that 1982 was little, if any, better for the industry than 1981 had been. Levels of production, trade, and consumption for virtually every major commodity declined; unit prices for most commodities fell, particularly in terms of constant dollars, and as a result of cutbacks in output and lower prices, capital available for investment within the industry was reduced. These conditions, coupled with the existence of considerable idle capacity, tended to retard investment, although there was an upturn in U.S. oil industry investment overseas. Despite the overall depressed situation of the world's mineral industry, there were indications of possible improvements in market economy countries near yearend, as output of some materials increased marginally and as prices for some mineral commodities reversed their downward trends. The downturns in total world mineral industry activity were not universal from the viewpoint of individual countries. Indeed, output of a number of commodities increased in centrally planned economy countries, and these gains were insufficient to offset declines in market economy countries, thereby sharply altering the proportion of total world output accounted for by each of these two groups of countries. There was a similar shift in consumption on a percentage basis.

Jan 1, 1984

By Sean Gallagher

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0°, 22.5°, and 45°). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined. Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01). Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (at least for older specimens) given knowledge of the spinal loads along with certain characteristics of the lumbar spine. Published by Elsevier Ltd. Keywords: Lumbar spine; Endplate fractures; Zygapophysial joints; Morphometry; Disk degeneration; Motion segments; Aging

Jan 1, 2006

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By Charles Will Wright

This paper will be of interest to those who are actually developing a mineral prospect or planning to do so, as well as to investors who are considering the problem of financing the development of the prospect, so that they may know what the risks are and what capital expenditures are necessary before a prospect may become a mine. The term "prospect" used broadly, as it is in this paper, is defined as any property that has a mineral showing of sufficient interest to warrant development, irrespective of prior work, Such previous exploration, however, may be extensive and consist of several tunnels or adits connected by raises, or of shafts with several levels. There may also be a small mining and milling plant on the prospect which, because of the lack of capital for development or the lack of markets for the products, is now idle. Such prospects may warrant further capital investment for development work or for a mine plant to raise to the stage of profitable production.

Jan 1, 1935

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By R. R. French

The industrial minerals industry in the Atlanta, Ga., area was studied in order to better understand problems associated with exploiting mineral resources in and near metropolitan areas. A method for delineating the Atlanta urban area and its component parts was developed so that the factors affecting the location of the minerals industry could be viewed mere objectively in the urban context. Major attention is focused on the area&apos;s dominant crushed stone subindustry Demographic and socioeconomic analysis of the Atlanta, Ga., area shows that expansion of the metropolis and its environs will probably eliminate potential mineral resources from the mineral resource base in the area, and that the expanding metropolis will be the primary determinant of future mining sites. Competition for land is accentuated to varying degrees by the incompatibility of wining operations with residential and other environmental requirements. Areas of consideration are suggested to provide maximum development of land and resources for greatest economic benefits it minimum social cost. Further research is recommended to determine market locations in urban areas, optimum operating levels for industrial minerals plants, and alternatives to surface mining.

Jan 1, 1970

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defense, for purposes other than the: extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation&apos;s natural nonmetallics is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of they Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952