Search Documents

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr, Fieldner and Davis, and others, has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M. standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting the results in those types of fuel which give erroneous results due to mechanical losses. This mechanical loss is usually designated as "sparking." There are two kinds of sparks or incandescent particles which may appear: particles of soot from partially condensed carbon from the burning gases, and unburned particles of the material itself which escape. The first type does not affect the accuracy of the volatile matter results, and is therefore negligible. The second type, however, causes appreciable loss and results in showing higher volatile percentages than actually exist.

Jan 1, 1932

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By Thomas M. Garland

A field study was made by the Bureau of Mines in cooperation with oil companies to determine the feasibility of changing the injection profile of water-input wells after water breakthrough at producing oil wells. A secondary objective was to study the particle size and quantity of plugging material required to change the input profile and the methods of applying these materials. Fifty-three injection wells were treated with various amounts and types of plugging materials and the injection profile was definitely changed in most of the wells treated. Increased efficiency of water injection after treatment was indicated by tracer surveys and injection-well performance. There were some indications that the rate of water production was reduced and the rate of oil production was increased as a result of selective-plugging treatments, but ,s found that an immediate change in the rate of oil and water production did not normally occur. In many cases, beneficial results from a treatment may never be observed in the rate of oil or water production due to the many factors that affect the performance of producing and injection wells.

Jan 1, 1966

By John D. Prater

Thallium is one of the rarer metals that has come into commercial importance in recent years. Although the element was first reported by Crookes in seleniferous deposits in lead chambers of a sulfuric acid plant in the Harz Mountains of Germany, it had no commercial significance until about 190O because of the high cost of extraction. Thallium occurs widely in the earth's crust but is found in such low concentrations that it is recovered only as a byproduct from processing other elements. There are no domestic ores of thallium; the entire output in this country is supplied by the American Smelting & Refining Co. as a byproduct of its cadmium operations at Globe, Colo. Thallium also is recovered from the flue dusts of sulfuric acid works in which thallium-bearing materials are used and as a byproduct of the lithopone industry. This paper describes methods for recovery of thallium from 'white arsenic" and lead Cottrell-precipitator dust of the American Smelting & Refining Co., lead smelter, Murray, Utah. Owing to an enlarged market for thallium because of increased military requirements and expanded peacetime uses, the Salt Lake Station of the Bureau of Mines surveyed the occurrence of thallium in ores, concentrates, and smelter products from all parts of the nation and found the most promising source was certain smelter products of the American Smelting & Refining Co. plant, Murray, Utah. Much of the thallium was being lost in marketed arsenic products; therefore, this investigation was undertaken to develop methods for recovering the thallium.

Jan 1, 1952

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By C. O. Ruud, R. E. Siemens, D. Chandra

The mineralogical constitution of a lateritic ore dictates the type of metallurgical process that can be used to extract valuable metals such as nickel and cobalt . To provide needed mineralogical information on the interrelationships of the metals contained in domestic laterites , the Bureau of Mines awarded a grant to Denver Research Institute to study the transition - type , low - grade laterites found in northern California and southern Oregon . For comparison , limonitic - type laterites from New Caledonia and the Philippines were also studied . X-ray diffraction , electron microscopy , electron beam analysis , and conventional petrography were used to determine the mineralogical associations of nickel and cobalt in the laterites . Results showed that for both laterite types studied most of the nickel and minor amounts of cobalt are associated with the mineral geothite ( FeO ( OH ) ) . Most of the cobalt and minor amounts of nickel are associated with a mixed manganese oxide (wad ) mineral .

Jan 1, 1983

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

By Louis H. Berkelhamer

"INTRODUCTION The method of differential thermal analysis suggested by Le Chatelier (1)1 in 1887 has recently emerged as an outstanding means of studying the constitution of various substances, particularly clays, soils, and miscellaneous hydrous materials (2). The literature ably discusses the applications and results obtained but has paid too little attention to specific details of construction of the apparatus. Knowledge of the apparatus is of importance to the experienced research man as is extremely useful to the novice v ho ventures into this field of analysis. Further, it is generally acknowledged that the variations in design and conditions of operation are one of the essential causes for differences in characteristic temperatures as reported by various investigators. A step forward in the elimination of such differences is the publication of the details of construction and operation of a simple and inexpensive apparatus that has proved useful at the southern Experiment station of the Bureau of Mines, where it was used in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jul 1, 1944

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By P. M. Gruzensky

Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step. With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C, and contained at least 100 grams of bismuth per liter, An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.

Jan 1, 1956

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By D. Harrington, W. J. Fene, H. B. Humphrey

In the fiscal years 1946 and 1947 the number of mine explosions decreased compared with the preceding years. However, the loss of life was so serious during the fiscal year 1947 the period when the Government administered bi- tuminous-coal and lignite mines that from April to June 1947 extraordinary measures were taken in mines then under Government possession to obtain com- pliance with provisions concerning rock dusting, ventilation, and blasting that had not been followed. The great loss of life in explosions during the fiscal year 1947 as compared with 1944, 1945, and 1946 is not easy to explain, but the necessity for maintaining adequate protection has been definitely demonstrated. Management, workers, and inspection agencies alike must keep the mines reasonably safe against explosions or allow them to lapse into a condition where chance is the principal protection against disaster. The at- tention given to protecting coal mines and the men employed in them against mine fires, following the disastrous fires in 1944 and 1945, has at least tem- porarily controlled this hazard loss of life from coal-mine fires was re- duced to 1 fatality in 1947. The number of fires was also less, and progress has been made in reducing the heavy losses in both life and property from un- derground coal-mine fires that occurred in the two years mentioned. Fatalities from mine explosions during the past 6 fiscal years, July 1942 to June 1947, totaled 674, and there were 149 explosions; during the preceding 6 years there were 655 fatalities in 132 explosions. The 6 fiscal years 1942- 47 cover the active period of Federal coal-mine inspection. During the fiscal year 1947, there were 154 fatalities from explosions compared with 58 during the fiscal year 1946, 64 in 1945, 94 in 1944, 152 in 1943, and 152 in 1942.

May 1, 1948

By R. R. McLellan

The Brown Derby pegmatites are in Gunnison County, Colo., about 18 miles east of Gunnison. Approximately 860 tons of lepidolite concentrates, with smaller amounts of microlite and beryl, was produced from 3 dikes of the Brown Derby group from 1943 through 1947. No mining was done from 1948 until December 1950, when production of lepidolite and beryl was resumed by the Poston Mining & Milling Co. Mining was intermittent during 1951 and 1952. The dikes were mapped and studied by the Federal Geological Survey during the field seasons of 1942 to 1944, and in May 1950 the Bureau of Mines initiated a diamond-drilling project to test the three dikes for lepidolite and beryl. After being recessed twice, the project was terminated indefinitely July 1951. Seven drill holes were completed for a total of 1,841.6 feet of drilling.

Jan 1, 1956

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966