Search Documents

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By R. E. Collom

The commercial development of petroleum and natural gas fields has reached its present status within 60 years and is still considered by some operators to be "100 per cent wildcatting." 1 A tendency to drill for gusher production, the production that yields big returns in spite of any mechanical defects in drilling methods, has frequently caused drillers to pass by oil-bearing strata of comparatively small yield and actually to overlook rich oil zones in proved fields; in addition, whole fields have been ruined by water because development methods were never carried beyond a hole-in-the-ground stage.2 Unfortunately, the petroleum industry has no mine dumps or tail. ing piles as at metal mines to yield fortunes through later and bette!' methods of treatment. The wasted oil and gas are gone, as are the time, money, and effort wasted in ill-advised or haphazard drilling. Probably as production costs increase less oil will be wasted, but the need to develop and produce from sands of low yield will become more urgent with the increase in consumption of oil and the decrease in supply. Hundreds of wells are producing steadily as the result of months and perhaps years of careful prospecting and of tests during drilling. The Bureau of Mines has studied the testing and drilling methods used at such wells, and presents in this paper a criticism of these methods and suggestions on future work. The term pr08- pecting here means correct identification and measurement of strata as they are exposed by the drill. The term testing means the determination of the kind and amount of fluid stored within the pores or crevices of any stratum exposed in the hole.

Jan 1, 1922

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By C. P. Bowie, George L. Gates

"INTRODUCTION Experience in drilling oil and gas wells has shown that the voidance of blow-outs, twist-offs, fishing jobs, loss of circulation, and heaving and caving of shale formations into the drill hole depends largely on how well the drilling-mud fluid serves its purpose. A possible method for the control of the drilling fluids may be seen from a study of the relation between the particle-size distribution and some of the important drilling-fluid properties, such as the ability to build quickly a relatively impervious mud sheath on the wall of the hole in the porous formations penetrated by the bit during drilling operations. In a wartime economy, which urgently requires conservation of steel, proper functioning of the drilling fluid is particularly important because, as Parks 4/ has stated, intelligent use of good drilling fluids makes possible drilling of wells for thousands of feet in open holes without the necessity of setting protective strings of casing to control the movement of salt water, gas, and troublesome formations into the borehole; consequently, especially in deep wells, of proper drilling fluids materially reduces the need for casing and lowers the cost of drilling and completing the wells."

May 1, 1942

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By Albert L. Toenges

The production of bituminous coal by stripping methods has become an important factor in some areas, especially in the Central and South Central States. In the latter, production at strip mines exceeds that at deep mines. Table 1 shows the tonnage produced at strip mines and the percentage of the total production for 1924 to 1935, inclusive, for the States in which the mines described in this circular are situated.4/ Following are references to earlier Bureau of Mines publications on strip mining of bituminous coal: Cash, F. E., and von Bernewitz, M. W., Methods, Costs, and. Safety in, Stripping and Mining Coal, Copper Ore, Iron Ore, Bauxite, and Pebble Phosphate: Bull. 298, Bureau of Mines, 1929, 275 pp. Kiessling, O. E., Tryon, F. G., and Mann, L., The Economics of Strip-Coal Mining: Econ. Paper 11, Bureau of Mines, 1931, 32 pp. Turner, Scott, and Bureau of Mines Staff; Mining Bituminous Coal by Stripping Methods: Inf. Circ. 6383, Bureau of Mines, 1930, 23, pp.

Jan 1, 1937

By McHenry Mosier

Mechanical loading, adopted long ago in open-pit, coal, and non-metal mines, was not used extensively in underground metal mines until the World War. In less than a decade it became standard practice in underground work in many mining districts. In 1924 the Missouri School of Mines and Metallurgy, in cooperation with the Federal Bureau of Mines, published a bulletin entitled "Mechanical Underground Loading in Metal Mines," which was prepared by Charles E. van Barneveld, mining engineer, Bureau of Mines.

Jan 1, 1940

By Virgil Miller, R. G. Knickerbacken

"INTRODUCTION The Bureau of Mines work reported by the Metallurgical Division 4/ in 1934 shows the possibility of producing artificial manganese ore by pre- ferential oxidation of manganese from spiegeleisen produced from manganiferous iron ores of the Cuyuna range, Minnesota. A three-step process is described as being capable of producing a ferrograde ore from this type of low-grade, domestic, strategic material. However, the melting temperature in the last step of the process that forms the manganese product is high, and the phosphorus content is not easily controlled. Also, the tenor of the manganese in the product is not comparable with other methods that use less process energy.Lofquist 5/ patented an improvement of the above three-step smelting method, in which sulfide was added to lower the melting point of the product.More recently, reputedly successful attempts have been made to reduce iron preferentially from manganiferous iron ores, simultaneously removing the phosphorus with the iron, by means of an unusually high temperature blast and excess coke.Anson G. Betts 6/ patented a process for the matte-smelting of manganese ores, in which the ore was mixed with pyrite and enough carbon or coke to serve as thermal energy and reducing, agent in a manner similar to the standard blast-furnace process. This process was intended to give pig iron, a manganese-iron matte, and a waste slag. Wood, Barrett, and Porath 7/ presented data on the treatment of low-grade, domestic, manganiferous iron ores and low-grade, domestic manganese ores by this Betts mattes pelting process."

Aug 1, 1942

By R. D. Brown

This Bureau of Mines report describes a new methodology for identifying and sorting scrap metals using two modern portable instruments: a thermoelectric sorter and a hand-held emission spectroscope. The method, tested on a 27-sample stainless steel and superalloy array, makes it possible to group and/or identify a typical mixture of high-value metal scrap in two or three steps, whereas as many as seven or eight steps are needed to perform the same separations using chemical spot tests. A portable fluorescent X-ray analyzer identified 19 of the 27 alloys in the sample array by name or type; these alloys are included in the microprocessor memory. The remaining alloys were identified by using the analyzer in its elemental analysis mode and comparing the results wit.h alloy specification chemistry.

Jan 1, 1984

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By G. R. Hopkins

The average gravity of the total crude petroleum produced in the United States during; the year 1927 was 32.2° A. P. I., or 0.864 in terms of specific gravity. A similar study, made by the U. S. Geological Survey in 1921, gave the average gravity at that time as 32.0.° To one who is accustomed to thinking of crude petroleum in terms of Oklahoma-Kansas and North Texas trades it may be surprising that the average gravity for the entire country is no higher than 32.20. The chief reason for this apparent discrepancy lies mainly in California production, which in 1927 amounted to over 25 per cent of the total, but which had an average gravity of only 24.10. A factor of less importance was Arkansas, which, though on the decline as a producing State, exerted a material effect by reason of its average gravity of 21.6°, the lowest for any State. In view of the heavy production of light crude in the Seminole area of Oklahoma during 1927, it would appear that the average gravity should have shown more than a 0.2 per cent gain over 1921. That this did not occur was due to the fact that in the interim between 1921 and 1927 important heavy oil discoveries were redo, notably the Smackover field of Arkansas.

Jan 1, 1929

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960

By Henry Kreisinger, WALTER T. RAY

General statement.-The briquetting tests conducted by the technologic branch of the United States Geological Survey had their beginning in the testing of coals and lignites at the Louisiana Purchase Exposition, St. Louis, Mo., in 1904. Briquetting tests were made at the fuel-testing plants at St. Louis, Mo., and at Norfolk, Va. Similar tests to be made at the experiment station of the Bureau of Mines at Pittsburg, Pa., form an essential part of investigations looking to the determination of the fuel value of the coals and lignites belonging to or for the use of the United States. The tests have comprised (1) the manufacture of briquets to determine the adaptability of different coals and lignites to the process and the merits of different binding materials; (2) physical tests to establish the fitness of the briquets to withstand weathering, transportation, and handling; and (3) steaming tests to prove the calorific value of the briquets in boilers of different types used by the Government, and, by comparison with the raw coals, the benefits to be derived from briquetting. Details of the tests have been issued in other publications. list of Government publications on fuel testing and briquetting is given at the close of this volume. Tests at Norfolk.-The fuel tests conducted at Norfolk included a detailed investigation of a number of Virginia and West Virginia coals that are bought by the United States Government for the Navy and for use in constructing the Panama Canal, and are extensively used by the merchant marine, manufacturing plants, and railroads. Through a cooperative arrangement with the Navy Department steaming tests of the coals were undertaken to determine the relative merits of the same coal when burned raw or as briquets in marine boilers. Preliminary arrangements were made between Joseph A. Holmes, then expert in charge of the technologic branch of the United States Geological Survey and now director of the Bureau of Mines, and Rear-Admiral Charles W. Rae, Chief Engineer of the United States Navy. The tests were made on board the U. S. torpedo boat Biddle, designated for the purpose, beginning December 6, 1907, and ending January 27, 1908. The coal used in these tests came from the Sewell and Beckley beds in the New River district of West Virginia. With the particular equipment used in the tests both coal and briquets were far. from smokeless; consequently the data of this bulletin are applicable only by analogy to parallel operation with a coal more nearly smokeless, but nevertheless applicable with much reliability. The possibilities of coals of different composition are indicated by the data to be published in a bulletin of the Bureau of Mines, wherein the present authors describe a number of tests in which only a very slight amount of smoke was emitted while burning raw coal from the Pocahontas No.3 bed, West Virginia, and briquets made therefrom at rates of combustion very much higher than any rates used in the torpedo-boat boiler. At a combustion rate of 120 pounds of the Pocahontas briquets per square foot of grate surface there was scarcely any smoke. It was the original intention to make a set of preliminary steaming tests alongside a dock (which tests furnish material for this bulletin) and to finish with a set of running tests at sea; but the running tests were never made, for lack of time and men.

Jan 1, 1911

By Jr. Joyce

This report describes sulfatization of nickeliferous laterites from Puerto Rico and the Philippines for recovery of water-soluble nickel and cobalt sulfates. Temperatures ranging from 665 C to 710 C and a 10-percent sulfur dioxide-air reaction gas were employed during batch-roasting tests and during continuous countercurrent treatment in a 2-inch-diameter shaft furnace. A maximum of 69 percent of the nickel and 76 percent of the cobalt were recovered from one sample of Puerto Rican laterite, and a maximum of 96 percent of the nickel and 91 percent of the cobalt were recovered from the Philippine laterite.

Jan 1, 1965

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984