Search Documents

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

By G. Richards

Research shows that having more women in the top mining jobs can bring bottom-line benefits. Mining companies are starting to embrace the need for greater gender diversity at board and senior management levels, figures and examples are given.

Jul 1, 2015

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By L. J. Cabri

Although no complete mineralogical balances have been published, the background knowledge and proven, highly sensitive analytical techniques to produce them already exist. For PGE-Cu-Ni sulphide ores a combination of ore microscopy, image analysis and electron microprobe analysis with proton microprobe analysis of sulphides for Pd, Rh and Ru and ion microprobe analysis for Pt, Ir and Rh (in some minerals) should provide the necessary data when combined with reliable assays. Other sulphide ores, such as the Cu-Ni-(PGE) ores of Sudbury, Ontario, require a similar approach except that the ion microprobe would be more suitable for the analysis of Pd, Pt and Rh because of its greater sensitivity. Oxide-silicate ores may be harder to deal with quantitatively, although the potential to confirm the presence of trace PGE within silicates and oxides may be greater than in PGE sulphide and Cu-Ni-(PGE) sulphide ores. However, solid solution of PGE in oxides and silicates still requires thorough documentation and evaluation in terms of their significance for the overall metallurgical balance

Apr 1, 1994

By A. F. Neil, A. S. Bahaj, P. Watkins, P. M. Hyslop, C. E. Kirby, P. A. B. James

The results of initial work indicate that for 3 of the 5 quarry sands bioleaching reduces the iron oxide content to a commercially acceptable 0.035 wt% Fe20 3, although the time taken to achieve this is 14-22 days against a target leach time of 7 day. Subsequent work has identified strains of Aspergillus niger that are more efficient at producing the array of complexing agents for iron and is yielding excellent and rapid reductions in Fe levels. Potentially, bioleaching offers a more environmentally friendly and energy-efficient process for the removal of Fe from glass-making sands than conventional routes but the production of organic acids by fermentation must be achievable with low-cost substrates such as sugar-beet molasses and lactose permeates for bioleaching to offer a commercially viable alternative to treatment with hot mineral acids. Silica sands usually contain three groups of Fe minerals: iron oxyhydroxides, which comprise crystalline types such as goethite and limonite tending to occur as thin, discontinuous coatings and in cracks and crevices on the surface of the quartz; the assemblage of heavy trace minerals, which include ilmenite, rutile, leucoxene, chromite and haematite, commonly present at levels of 0.1 wt% or less as discrete grains or sometimes cemented to the quartz; and clay minerals cemented in pits on the surface of the quartz and in association with weathered, discrete feldspars. The response of the assemblage of iron minerals to short periods of exposure to hot inorganic acids is broadly related to which group they belong to, those that form coatings being accessible to acid and tending to react rapidly whereas the trace minerals are usually resistant and react very slowly, if at all, and the clays are probably digested. The note reports on a preliminary study of the use of microorganisms to develop an alternative clean technology that will give results comparable to those achievable with hot inorganic mineral acids but with more environmentally acceptable procedures. Various fungi and bacteria produce organic acids when grown in certain media. When these acids come into contact with Fe-stained sand grains the iron is removed as soluble complexes. Several strains of Aspergillus niger have been found to produce organic acids from sugar, predominantly citric, gluconic and oxalic acids, their relative yields depending on cultivation medium and conditions. Sand samples were prepared from five quarries in the UK: Levenseat, Lothian; Redhill, Surrey; King's Lynn, Norfolk; Chelford, Cheshire; and Oakamoor, Staffordshire; ranging in iron oxide content from 0.035 to 0.153 wt% Fe203

Jun 18, 1905

By J Hadijigeorgiou, R. W. Lawrence, R Pouling

The layered co-mingling method involves the disposal of waste rock with the addition, at predefined construction stages, of layers of dewatered mine tailings. The resulting waste structure displays bulk properties that are more favourable to acid rock drainage (ARD) control than the constituent materials alone. A laboratory test programme was conducted to examine the potential of this method. Columns containing different configurations of waste rock and tailings were percolation leached for 40 weeks and the leachates examined for various parameters. In the short term the chemical reactions that result from the introduction of dewatered tailings into rock waste can significantly improve the quality of the drainage. Columns with co-mingled material produced leachate with pH levels of 8, whereas leachate from the control column containing waste rock alone had a pH of 4. Larger-scale field tests are planned to determine the effect of the disposal method over the longer term

Apr 1, 1996

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905