Search Documents

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By A. S. Chekmarev, T. Z. Lygina, K. G. Egorova, A. V. Skvorcov

"We have conducted analytical and technological evaluation of sepiolite containing clay. The possible areas of application of the sepiolite have been investigated and complex methods of enrichment of natural sepiolite have been identified. It was determined that for preserving the structure of minerals after processing the most effective method of the natural agglomerates disintegration was the soft abrasion of the clay fraction up to 0,5 mm. Disintegration of sepiolite clay along with using high energy-stressed effects on the matrix can deteriorate the rheological properties of clay suspensions and reduce the yield of drilling mud and sorption properties. To improve the quality of clay powders we used combined gravity-modifying method of wet enrichment. After the wet enrichment the yield of drilling mud increased up to 12.7 m3/t, with the addition of MgO up to 20,3 m3/t. It was noted that drilling muds contenting more than 50% of sepiolite are stable in mineralized (salt) waters. Based on the studied activated sepiolite rocks we obtained the effective heat-insulating materials with relatively low thermal conductivity – 0,165 W/m·K, average strength – 7,29 MPa and water absorption-49,0%.INTRODUCTION The modern development of the Russian economy requires the implementation of scientific and technical tasks. The solutions of it involves a radical reduction in energy, heat losses and material consumption of products, rational and efficient using of all types of resources, as well as the using of new types of mineral raw materials and materials based on it. An example of a new type of mineral raw materials for Russia is sepiolite containing rocks, due to unconventional conditions for their soils accumulation in the climate of the Far North. Sepiolite is a unique type of nonmetallic mineral. It is formed in soils, marine and saline basins, occurs in carbonate and carbonate-clay rocks in the form of lenses and lens – shaped layers, rarely nodules, loose powdery masses, shell-like concretions. Sepiolite may have a soft porous macroscopic appearance or less often the structure of the fibrous mass. Color of sepiolite is from white to cream with gray, green, pink and even crimson shade depending on the degree of pollution. Sepiolite can be in two forms - a-sepiolite (parasepiolite), which occurs in the form of large packets of crystalline fibers and ß-sepiolite, which occurs in the form of amorphous aggregates or small flat rounded particles. The sepiolite fibers have a length of from 0.2 to 2 Å, width from 100 to 300 Å, the thickness from 50 to 100 Å (Geological dictionary, 1973)."

Jan 1, 2018

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By Thi Hien Tran, Huy Hoan Nguyen, Thi Thu Hien-Dinh, Hong Son Nguyen, Duy Anh Dao

"Lithium discovered in La Vi deposit, Quang Ngai province in the Central of Vietnam was estimated with a reserve of approximately 1.5 million tones of lithium ore, which was characterized by mainly lepidolite with muscovite, albite, and quartz. This study investigated reasonable flowsheet and optimal conditions of enrichment technology for lepidolite from the mined ore by flotation process, and producing Li2CO3 and LiCl from lepidolite concentrate by hydrometallurgical process. The significant conditions for froth flotation of lithium ore including particle size, pH of ore slurry, pulp density, chemical spending (collectors, activators, depressants, and frothers), stirring and flotation time were investigated. The identified reasonable flowsheet and optimal conditions for froth flotation the La Vi lithium ore processed lepidolite concentrate containing up to 4 wt.% Li2O with a recovery of 87.61 wt.%. The processes of sulfation roasting lepidolite concentrate using FeSO4.7H2O, then leaching in H2SO4 solution, and removing impurities were carried out to prepare a pure lithium-bearing solution for producing Li2CO3 and LiCl. The products containing 99.05 wt.% of Li2CO3 and 99.02 wt.% of LiCl were obtained with recoveries of 82.97 wt.% and 85.77 wt.%, respectively. The obtained results indicated that lithium ore in La Vi deposit can be processed to produce commercial lithium products and lead the study to develop technology for a new industry of lithium processing in Vietnam.INTRODUCTION Lithium is the lightest metal, which has many superior properties in both metal and compound (such as Li2CO3, LiCl...) states since its discovery in 1817 by Swedish chemist Johan August Arfwedson. Lithium is a favourable material for many high technology fields such as aerospace industry and chemical industry. Some industrial fields which present the main consumptions of lithium include ceramic, glass, aluminum alloy, lubricants, rechargeable Li-ion batteries, synthetic rubber, and pharmaceuticals. The worldwide production of lithium in 2014 was 31,700 tones, continually increased in 2015 of 5% presented 32,500 tones (USGS, 2016). The demand for lithium tends to increase because of the raising in consumption of lithium batteries. Lithium is mined from salar brines, mainly in Chile and Bolivia, but also from granites and pegmatites, which contain minerals with high lithium content such as spodumene - LiAlSi2O6 (Heinrich et al., 1978; Linnen et al., 2012); petalite - LiAlSi4O10 (Sitando & Crouse, 2012); zinnwaldite - KLiFe2+Al(AlSi3O10)(F,OH)2 (Paukov et al., 2010; Kondás J. & Jandová J., 2006); lepidolite - K(Li,Al)3(Si,Al)4O10(F,OH)2 (Luong et al., 2013); and amblygonite - LiAlPO4F (Garrett, 2004)."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By Jun Xiao, Yucai Zhou, Yanhong Dong, Daixiong Chen

"In this article research on the mineralogical characteristics and beneficiation process for a copper molybdenum deposits in Heilongjiang province of China has been carried out. Chemical analysis, X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANning electron microscopy (QEMSCAN) were conducted on samples. The bulk analysis results showed that: (1) Comprehensive recovery and separation of molybdenum & copper minerals was feasible by the flowsheet of first copper-molybdenum mixed flotation after grinding the ore samples to 61.88% -74µm and then separation flotation of copper and molybdenum after regrinding the Cu-Mo mixed concentrate to 83.26% -38 µm. The results highlight relationship between mineralogical characteristics of ore and comprehensive benefication method. (2) the combination of "" Sodium sulphide and sodium thioglycolate "" reagents are effective inhibitors of copper-molybdenum mixed concentrate, their selectivity performance is better than that of single reagent. Good flotation indexes were gained that might be directive experience to similar cases. KEYWORDS Mineralogical characteristics; molybdenite; chalcopyrite; flotation separation; inhibitor INTRODUCTION Copper and molybdenum metals are widely used in the field of metallurgy, aerospace, national defence, etc. Copper –molybdenum sulphide ore is an important source of copper and molybdenum metals. At present flotation is still the preferred methods to deal with the copper-molybdenum sulphide minerals (Yin, Z., Sun, W.et al. 2017; Ansari, A., & Pawlik, M. 2007; Hirajima, T., Miki, et al. 2017). Copper and molybdenum sulphide ores usually have the similarly good nature floatability(Miki, H., Matsuoka, et al. 2017), meanwhile most molybdenum sulphide ore has tiny grained-size(Castro, S., & Laskowski, J. S. 2015.) and closed relationship with other sulphide and gangue minerals which result in the coper and molybdenum separation problem. Base on the nature of the ore and flotation properties of the individual minerals contained in the ore, there are two methods are usually used to deal with the copper – molybdenum ore, including bulk molybdenum/copper flotation followed by separation of copper and molybdenum minerals, sequential molybdenum/ copper flotation(Liu, G. Y., Lu, et al. 2012). The latter method has the shortcoming of hard to activate the depressed copper minerals in the previous molybdenum flotation process, which may result in a large loss of the copper from concentrate, this disadvantage would avoid while adopting the former method. bulk flotation followed by separation process is to get the copper-molybdenum concentrate from raw ore first then separate flotation the molybdenum and copper minerals, benefit from the excellent floatability of both molybdenum and copper minerals ( Malhotra, D., Rowe, R. M., & Bhasin, A. K. 1986; Cao, Z., Yue, et al. 2017 ), it really easy to obtain the mixed concentrate. In order to get the high quality copper and molybdenum concentrate, the key technologies and difficulties are to realize the separation of the copper and molybdenum minerals which have the very similar natural floatability (Raghavan, S., & Hsu, L. L. 2015; Nakhaei, F. 2014)."

Jan 1, 2018

By M. H. Moys, M. M. Bwalya

"INTRODUCTIONThe grinding rate prediction scheme makes use of the energy spectra output from the DEM simulations and the statistical quantification of material strength, which can be done using the drop-weight tester or some other similar equipment. The prediction scheme is evaluated using milling experiments performed under well-defined conditions.MATERIAL STRENGTH QUANTIFICATIONUsing the drop weight test machine, particles of a wide size range were broken singly using different energy inputs. A characteristic equation key to milling rate prediction that relates the probability of fracture with energy input and number of impact attempts was obtained and is stated as follows:"

Jan 1, 2003

By Janusz S. Laskowski

"Frothers offered by different manufacturers are marketed with some information on their chemical and physical properties (e.g. density, viscosity, color, water-solubility, safety/toxicity, etc.). But frothers are used in flotation to generate fine bubbles and to stabilize the forth, and this information is only provided in a very qualitative description of the visual appearance of bubbles and froths. The terms “powerful” and “selective”, which have been commonly used to characterize frothers, have intuitive rather than scientific meaning.This paper introduces the DFI (Dynamic Foamability Index) plotted vs. CCC (Critical Coalescence Concentration) diagrams to classify flotation frothers (Fig. 1). The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers."

Jan 1, 2003

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

In this paper, various methods, such as XPS, XRD, SEM and zeta potential measurement are applied to investigate the action mechanism of sodium sulfide in flotation of lead and zinc oxysalt minerals. The experimental results show that the mechanisms of sodium sulfide in flotation of lead oxysalt minerals and zinc oxysalt minerals are different: on the surface of cerusite, there is lead sulfide phase formed under the reaction of sodium sulfide, resulting that the cerusite surface shows the form of galena, which is advantageous to the adsorption of anion collector and improves the floatability of cerusite as a result. On the surface of zinc oxysalt minerals, there is no zinc sulfide phase formed, but the sodium sulfide increases its surface electronegativity, and enhances the adsorption of cation collector lauryl amine, so the floatability of zinc oxysalt minerals is improved. The difference of action mechanisms of sodium sulfide on lead and zinc oxysalt minerals exactly explains the reason why different collectors are selected in the flotation of cerusite and smithsonite, which are both carbonate minerals although.

Jan 1, 2014

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012

By D. Moradkhani

The objective of this research was, to evaluate the hazard of heavy metals in the soil around the National Iranian Lead & Zinc (NILZ) Company. In this study, 38 samples of soil around the NILZ factory were collected using standard sampling method, so that, the heavy metals Pb, Zn, Cd and Cr have been evaluated. The concentration of heavy metals were measured and compared with standard limits. The results show that the hazard of heavy metals in soil is not so serious and the content of Pb in just 5 percent of samples, and the content of Zn in just 3 percent of samples were above standard limits and the concentration of Cd and Cr were under the standard limits. Average, variance and standard deviation of the elements are calculated and with due attention to the standard deviation, Pb and Zn are seen to be more distributed than Cd and Cr. Also the isograde curve of heavy metals was drawn using software called Surfer. These curves showed that the heavy metals are concentrated at particular distances from the factory. Keywords: heavy metals, remote sensing, sampling method, isograde curve, Surfer software

Sep 1, 2012

In order to determine the optimal process parameters of agitation leaching and provide industrial process design parameters, experiments were carried out on leaching behaviors of copper oxide ore with high mud content. Condition tests show that the main factors affect the leaching efficiency as follows: Temperature, Initial acid concentration, leaching time and particle size. As the temperature increases, the copper leaching rate was increased. At 60 ?, the initial acid concentration 80g / L, leaching time 2h, liquid-solid ratio 2:1 and grinding fineness65%-0.074mm, the optimal copper extraction was 83.15%, the acid consumption was 187.91kg / t. ore. Keywords: agitation leaching, copper oxide ore, mud

Sep 1, 2012

By I. V. Makarskii, D. N. Nikitin, L. G. Tarasova

"The extent and nature of the damage to diamonds at processing plant is largely determined by the design features of the equipment, the characteristics of the feed ore and the parameters of the ore disintegration process (change in the rotational speed of the autogenous mills, variations of the water supply to comminution process, choice of the optimum charge, etc.). To monitor the intactness of diamonds, an instrumental method using the X-ray tomography system and colored synthetic indicator diamonds was developed for identifying the process-related damage. The X-ray tomography system consists of a CT-Portable X-ray tomographic scanner, a crystal positioning device and customized software (developed by the Fraunhofer Institute and Aliud GmbH, Germany). The developed method enables improvement of the accuracy of the results, exclusion of the subjectivity of the mineralogical assessment, acceleration of data processing and promptly planning of the activities aimed at reducing the process-related damage to diamonds. KEYWORDS Diamonds, colored indicator diamonds, process-related damage, loss of mass, instrumental method, X-ray tomography system. INTRODUCTION Industrial tests of ore processing technology at the enterprises of ALROSA PJSC are accompanied by assessment of the process-related damage to diamonds. The assessment of the process-related damage to crystals is carried out for prompt elimination of factors contributing to the increase of impact forces in the process flow sheet of ore treatment plant. For this purpose a specially selected parcel of -4.0 + 2.0 mm sized natural indicator diamonds is used. The diamonds are exposed to ionizing radiation in order to turn them green and thus to create a distinctive feature. Colored natural indicator diamonds are described, photographed in several views and introduced into the process flow sheet of the processing plant, then extracted from the process flow, described and photographed again. The comparison of diamonds before and after their passing through the process flow sheet of the plant allows to find evidence of process-related impact on the crystal and to calculate the factor of process-related damage (the number of crystals damaged during liberation and recovery), the loss of crystal weight and the degree of damage to the crystals. The method of colored indicator diamonds is used to select processing methods, equipment or regime which would be the safest for diamonds based on the analysis of the factors of process-related damage. There are limitations of the method, such as:"

Jan 1, 2018

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014

By Gorki Davila, Irineu Brum

"Brazil has large reserves of coal (32 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country&apos;s strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario the processing of Brazilian coal by flotation appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dam. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. The types of collector reagent and foaming employees result in different concentrates. This study also presents a preliminary analysis of the effect of water recovery in concentration parameters."

Jan 1, 2014