Search Documents

By Larry Stearns, Lori Tiefenthaler

Remediation of contaminated soil represents a significant market for application of Deep Soil Mixing (DSM). Eighty-one percent of U.S. Environmental Protection Agency (EPA) Superfund Program’s site remedies have involved contaminated soil. Contaminated soil is frequently treated by In-situ Solidification/Stabilization (ISS). ISS treatment of contaminated soil involves mixing binding agents into soil using DSM techniques. DSM is a core business for many DFI members. Members may improve and broaden their services to clients by learning about the recent ISS treatment of contaminated soil at a Superfund site. ISS treatment is part of the EPA-selected remedy for a Superfund Site in the metro New York City area. The property has seen heavy industrial use for more than a century. Soil at the site is contaminated with a variety of volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) including coal tars and heavy metals, principally arsenic and lead. Beginning in 2017 and continuing through 2018, approximately 150,000 cubic yards (115,000 cubic meters) of soil will be treated by ISS at the case study site. Portland cement and slag cement are mixed into the soil by DSM techniques using GPS guided excavators to immobilize the hazardous constituents within the treated soil. ISS treatment by DSM will contribute to redevelopment of this valuable property. This paper will describe ISS constructability and performance, case study grout mix design with geotechnical results for strength and permeability, and deep soil mixing techniques. INTRODUCTION In-situ solidification and stabilization (ISS) is a deep soil mixing (DSM) technique applied in the environmental remediation field to physically encapsulate, or chemically bind, contaminates of concern such that the impacts to human health and the environment are mitigated. Common remediation applications of ISS include mixing cementitious reagents into contaminated soils to form a monolithic mass with desired performance characteristics, and the installation of vertical subsurface walls designed to control groundwater movement. A key characteristic of ISS is that the contaminated soils are treated in their existing location at the project site and then are left in place after treatment. Typical performance characteristics of the ISS treated soils include improved unconfined compressive strength (UCS), reduced hydraulic conductivity (HC), and reduced leaching potential of soil contaminants. Increased shear resistance of the treated soil may also be a performance requirement where seismic loading is a concern.

Jan 1, 2018

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

By Jerry F. Parola

In current practice, pile foundation design is based on a general under-standing of pile-soil interaction during installation and superstructure-pile-soil interaction after construction. The pile design is a reflection of experience, precedent and judgment for normal piling practice of working load capacities up to approximately 100 tons with corresponding ultimate capacities up to 200 tons. For higher capacity piles, pile design is even less predictable. In particular, the feasibility of pile installation is an important design consideration that must be given the proper attention. An installation capability that is not given the required emphasis can cause unnecessary problems.

Jan 1, 1986

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By William D. Spielvogel

The Massachusetts Highway Department awarded the Porter Street Outfall Project to the J.M. Cashman Company in November 1991. Timely completion of the Project in one and one half years is critical to the start of the subsequent Third Harbor Tunnel North Approach project. Existing subsurface conditions and the Project's location at Boston's Logan International Airport significantly increases the difficulty of construction. The major contractual work involves relocating a reinforced concrete double box culvert supported on a continuous wood pile foundation. This existing culvert crosses and interferes with the future Third Harbor Tunnel North Approach alignment. Two parallel culverts constructed approximately 20 feet from either side of the future Third Harbor Tunnel alignment replace the existing double box culvert structure. Under the original contract design, approximately 3,100 feet of 14 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the west side of the Third Harbor Tunnel and is located in the center of the Airport's main service roadway, Harborside Drive. This culvert is the Porter Street Combined Sewer, PSCS, which handles a combined flow of sewerage from the East Boston community and storm water runoff from Logan Airport. In addition, approximately 2,230 feet of 17 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the east side of the Third Harbor Tunnel and is within 20 feet of an active aircraft taxiway and heliport. This culvert is the Bird Island Flats Storm Drain, BIFSD, which handles storm water runoff from the Logan Airport airfield. The existing outfall, on the west side of the Third Harbor Tunnel alignment is to remain in service and is to be connected to the new PSCS and BIFSD culverts. Therefore, a portion of the BIFSD culvert is designed as a bridge to span 128 ft. across the Third Harbor Tunnel excavation during construction.

Jan 1, 1994

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995

By R. G. Horvath

The Statnamic loading test is a new and innovative method for testing deep foundations. The test is relatively inexpensive, quick, easily mobilized, provides for direct measurement of applied load and corresponding displacement, and is capable of very high loading capacities. The long duration of the applied loading, as compared to a dynamic loading test, allows for a straightforward determination of the static behaviour of the foundation tested. A new method of analysis of the Statnamic loading test, the Equilibrium Point Method, is presented. A description is given of the pile-soil model and a demonstration of how the static load-displacement behaviour of deep foundations may be predicted from the Statnamic loading test data. The Equilibrium Point Method of analysis is applied to three types of deep foundations in soils which respond differently to fast loading rates. These case histories, from Canada and the United States, include data from static loading tests for direct comparison, and demonstrate the ability of the Equilibrium Point Method to predict static behaviour of the deep foundations.

Jan 1, 1993

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018