Search Documents

By W. E. Selnes

Introduction In 1938, a survey conducted by the Ontario Mining Association revealed a rather startling fact. Injuries incurred in chute pulling were more numerous than those from any other single cause. This report prompted Mr. W. B. Paton, then Inspector of Mines for Manitoba, to make a similar survey of the mines of his Province. It indicated that, in Manitoba mines, chute accidents ranked second only to those from falls off roofs and sides. Why has the mining industry been so slow to recognize the dangers of chute pulling? A partial answer may be the lack of any systematic classification of accidents according to their real cause. The result has been to attribute to other causes injuries which were a direct outcome of chute pulling, and, indeed, has made it difficult to analyze accidents in the industry as a whole. Perhaps, too, because chutes are generally located in the comparative safety? of the drifts, there has been a tendency to consider the occupation as not very hazardous. Not until enough statistics were obtained on this particular task could it be appraised correctly. The Mining Association's survey has been most helpful, and latterly the industry has done a great deal toward analyzing the causes of chute accidents and toward determining an effective means of overcoming them. Much, however, remains to be done. An effort will be made in this paper to outline methods which have been found successful in materially reducing the number of injuries. Qualifications of the Chute Puller First of all it must be realized that chute-pulling is a specialized occupation. The men require proper training for the job, just as in other mining operations. Care must, therefore, be taken to choose persons whose qualifications fit them for the job. Chute-pulling is an integral part of the general mining operation and cannot be considered as isolated from the tasks of other workers. One of the essential qualifications of a chute-puller is a sufficient knowledge of mining operations to appreciate the effect his work will have on the safety of others in the vicinity. He must take the necessary precautions, by verbal warnings, by placing barricades and signs, or by personally guarding the chutes, to prevent accidents to fellow workers.

Jan 1, 1947

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By F. H. Edmunds

Introduction This paper, it is hoped, will serve as an introduction to further work upon the origin of the soils and to a more complete interpretation of the geology of Saskatchewan from a study of the soils of the Province. The great difficulty that is encountered in mapping the structure of the prairie regions of the west must be evident to all who have made the attempt. The rarity of good exposures, due to the extensive coverings of glacial drift, is the greatest obstacle, making it difficult to determine the exact stratigraphical position of such exposures as may be found. In many cases palæontological evidence is lacking, or, if available, our present knowledge of the stratigraphy is insufficient to justify division of the formations into horizons; and until many of these formations have been subjected to petrographic investigation, little can be done in using lithological differences as an aid to the correlation of the usually sparse outcrops met with in the Province. Topography may be of the utmost value as an indication of geological structure when considered in conjunction with other evidence. It does not necessarily follow that, because an area in Saskatchewan has resemblances in surface configuration to an area of oil-producing land in Texas, there is sufficient justification for sinking money in wells without further investigation. Such - investigation should include the study of available soil maps.

Jan 1, 1929

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

By Hyung Sup Choi

The preparation of high-purity zirconyl compounds was studied in order to develop an economical process for obtaining pure zirconium via the caustic fritting of zircon sand. The direct dissolution of caustic frits with concentrated hydrochloric or nitric acid at 80c. followed by the addition of a small amount of acidified gelatin, gave high-purity zirconyl chloride or nitrate. The addition of a small amount of gelatin caused a mutual flocculation between colloidal silica and gelatin. The precipitation of this silica floc markedly lowered the content of silica in the product. The silica content of the compounds (or solution) so produced, generally less than 100 ppm., was sufficiently low for tributyl phosphate extraction for nitrate solutions. It was found that the degree of purification de-pends not only on the procedures employed but also on the nature of the frit itself. Silica was more effectively eliminated from the fritted product produced at higher temperatures, and less silica was present in the com-pound prepared from the frit produced in a shorter heating time. In order to ascertain the nature of the

Jan 1, 1965

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By G. Issid, J. McGinty, C. Lee, Y. Pepin

For more than a decade, Hatch has used process and logistics models to assist Rio Tinto Fer et Titane (RTFT) with capacity planning, debottlenecking, and optimization to help ensure design capability, capital effectiveness, and operational efficiency of the integrated production chain. Process models are used to optimize the physics-based aspects of the system, such as mass and energy balances, flow rates, yields, and equipment specifications. Dynamic logistics models are used to optimize how the various plant areas work together to achieve the desired ends and deal with such things as plant scheduling and synchronization strategies, sizing of buffers between processes, defining the required number of process and material handling units, and designing a plant layout that minimizes plant interferences and inefficiencies. The combined use of process models and logistics models enables the overall plant to be optimized from both a productivity and quality point of view, with each plant area working in harmony with one another to achieve targeted capacities and efficiencies. This paper describes the many benefits derived from such modeling efforts over the past 15 years for each of the major plant areas at RTFT: Beneficiation Plant, Smelter Plant, Steel Plant, UGS Plant, and Powder Plant (RTMP).

Jan 1, 2011

By T. Verdel, Y. Gunzburger

Rockfalls are major and essentially unpredictable sources of danger, particularly along transportation routes (roads and railways). Thus, the assessment of their probability of occurrence is a major challenge for risk management. From a qualitative perspective, it is known that rockfalls occur mainly during periods of rain, snowmelt, or freeze-thaw. Nevertheless, from a quantitative perspective, these generally assumed correlations between rockfalls and their possible meteorological triggering events are often difficult to identify because i) rockfalls are too rare for the use of classical statistical analysis techniques and ii) all intensities of triggering factors do not have the same probability. In this study, we propose a new approach to investigate the correlation of rockfalls with rain, freezing periods, and strong temperature variations. This approach is tested on three French rockfall databases, the first of which exhibits an outstandingly high frequency of rockfalls (approximately 950 events over 11 years), whereas the other two databases are more typical (approximately 140 events over 11 years). These databases come from (1) the national highway RN1 on La Réunion Island, (2) a railway in the Bourgogne-Franche Comté region, and (3) a railway in the Auvergne region. Whereas a basic correlation analysis is only able to highlight an already obvious correlation in the case of the “rich” database, the newly suggested method appears to detect correlations even in the “poor” ones. Indeed, the use of this method confirms the positive correlation between rainfalls and rockfalls on La Réunion Island database. This method highlights a correlation between cumulative rainfalls and rockfalls in the Bourgogne region, and it detects a correlation between the daily minimum temperature and rockfalls in the Auvergne region. This new approach is easy to use and also serves to determine the conditional probability of rockfall function of a given meteorological factor. This approach will help to optimize risk management in the studied areas based on their meteorological conditions. Nevertheless, even if some rockfalls are correlated to meteorological factors, other seems to occur independently of these factors, which highlights the unpredictability of rockfall hazard.

Jan 1, 2015

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By A. E. Hilder

Introductory The following pages present the results of field investigations, laboratory and commercial tests, drilling, surveying, and preliminary development of the refractory clays which have been discovered recently in the township of Kipling, at the foot of Long rapids on the west side of the Mattagami river about 57 miles north of Kapuskasing and approximately 7 miles north of Smoky Falls, the terminus of the privately owned railway operated by the Spruce Falls Power and Paper Company, Kapuskasing (see Figure 1). Investigations on the clays of northern Ontario have been carried on over a period of seven years by officers of the Ontario Department of Mines, and I am indebted to the information published by that Department in reports by W. S. Dyer and A. R. Crozier, as well as?by Professor R. J. Montgomery, of the Ceramic Department, University of Toronto. It was, in large measure, the data given in the 37th, 38th, and 42nd Annual Reports of the Ontario Department of Mines that led me to make a personal investigation of the Mattagami River clays, with the result that we now have a commercial undertaking that will develop eventually into an industry of considerable importance in supplying the central manufacturing districts of Canada with refractories that heretofore have been largely imported from the United States. An extract from the 42nd Annual Report of the Department, Part III, 1933, page 75, reads as follows: "As for the refractory clay, the deposits are undoubtedly very large, but what is urgently needed is a deposit near the railway under sufficiently shallow overburden for recovery by stripping'. Having previously made an investigation of the clays adjacent to the Temiskaming and Northern Ontario railway, and these clays proving unsuitable, I turned my attention to the outcrops of refractory clays on the Mattagami river, first reported by Keele in 1919. This area offered possibilities within the economically permissible distance from rail transportation.

Jan 1, 1935

By S. Bergquist

In this paper, it is investigated how different types of automation would affect the safety for workers in asphalt paving. The risk for the workers on road construction sites is consistently high in comparison to the average risk of the working population. Automation has been suggested as an alternative for improving the safety in roadside construction assuming that removing workers will inherently eliminate the risk of them being injured. In this paper, the potential for improving the safety using automation is analyzed in detail. By investigating accident statistics and understanding the type of accidents that appear, several different automated functions for increased safety are proposed and described. Based on available statistics, it is possible to estimate the safety benefit, as the reduction in fatalities, for several of the proposed functions. The highest safety benefit would be achieved by automating the road traffic driving through the work zones. This has the potential of reducing the total number of road worker fatalities with over 30 %. In addition, it would decrease the number of road traffic accidents in work zones. Automation of construction machinery and dump-trucks also has the potential to increase the safety.

Aug 1, 2013

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017