Search Documents

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

Leadership "Organizing a group of people to achieve a common goal" Paradigms ? Rush to produce or cut costs. ? The most important thing after safety is production. ? We?ll take care of ??this?? once in production. ? I know what to do, 30 years of experience in mining. ? I want a 100% reliable operation.

Aug 1, 2013

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By K. K. Murray, D. G. Gelderland

"The pressure oxidation autoclave at the Goldcorp’s Red Lake Gold Mines (RLGM) was commissioned in 1991. Since commissioning, the circuit has been well maintained and its capacity increased to mechanical and gaseous oxygen limitations. With advances in available technology, opportunities to produce more sulphide concentrate and a changing business environment, an optimization project has been initiated at RLGM. A multi-phase approach has been developed to optimize both the operations and economics of the circuit. This paper describes the history and future of the autoclave circuit at RLGM.AcknowledmentsWe would like to thank the operations and maintenance staff at Red Lake Gold Mines for their support and openness of mind to enact changes to enhance the operation. We would also like to acknowledge the members of the integrated team from Red Lake maintence, metallurgy, operations and corporate technical services that did the hard work to push past the status quo in order to advance productivity.OpportunityThe Red Lake Gold Mines (RLGM) pressure oxidation (POx) circuit has been in operation for over 25 years processing the high sulphide content gold bearing minerals. Increased sulphide concentrate production from improved flotation recovery and increasing gold sulphide association at depth has led to the POx circuit becoming a throughput bottleneck. The opportunity exists to process increased tonnages of sulphide concentrates and increase gold production. In order to realize this value, it will be necessary to increase the throughput capacity of the POx circuit.BackgroundThe POx autoclave at the RLGM, commissioned in 1991, was Canada’s first gold autoclave. It was installed to replace the two-stage fluid bed roaster that was built when the Campbell mine and mill were constructed in the late Forties. The circuit was originally designed to process 12.5 t/d sulphide sulphur in about 50 t/d of Campbell flotation concentrate. Following the merger of the Campbell and Red Lake Mines in 2006, the POx circuit started processing flotation concentrate from both Campbell and Red Lake Mills. In recent years, the circuit has been processing about 18 t/d sulphide sulphur in 75-85 t/d flotation concentrate."

Jan 1, 2017

By Barrick Pierina, John Frostiak, Igor Gonzales, Kenneth G. Thomas, Ken Manning

"1.0 SummaryThe Pierina deposit was acquired in August 1996 when Barrick Gold Corporation purchased Arequipa Resources, a junior mining company with extensive land positions in Peru. At the time of acquisition, Arequipa had developed two exploration tunnels and drilled 9 exploration holes on the property. Metallurgical tests, conducted on samples taken from the tunnels and the exploration holes indicated that the ore was amenable to heap leaching. Barrick’s exploration team recognised from the outset, the potential of the mineralisation and convinced Barrick’s senior management that this was indeed a world class deposit that should be pursued. On November 25, 1998, the first dore was poured at Pierina, 27 months from the time of acquisition. During that period Barrick completed its exploration programme, prepared a development plan including capital and operating costs, production profiles and cash flow forecasts, and a schedule to develop a mine and construct a leach pad and gold recovery plant, including all supporting infrastructure. All permits and environmental approvals were obtained and all necessary land was acquired. The project was completed on schedule and under budget. This was the first greenfield mine development for Barrick outside of North America.This paper details, mainly, the research and development, engineering, construction and commissioning of the metallurgical process facilities.2.0 The Develonment ProgrammeImmediately after the acquisition, Barrick began the process of gathering information required to prepare a project development plan. Kilborn Engineering was retained to assemble all of the information collected and collated into a development plan document. This document was completed by June 16,1997. The objective was to bring the mine into production as quickly as possible with critical activities identified as follows:"

Jan 1, 2000

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By D. C. McDonald

"IntroductionTHE GIANT YELLOWKNIFE property is on the west side of Yellowknife bay, Great Slave lake, N.W.T., some 600 air miles north of Edmonton. This paper deals with the underground development and mining of the complex system of orebodies which have produced, in the first fifty-six months of operation (May, 1948, to December, 1952), 652,464 tons of ore with an average grade of 0.80 ounces of •gold per ton (1).The mine has been developed from three vertical shafts designated A, B, and C. Figure l shows the positions of these openings with respect to the known ore-bearing zones and the surface plant.A shaft was sunk to a depth of 522 feet in 1945-46, primarily as a prospect shaft for investigation and development of the East Zone orebody. Drifting was carried out on the 200-and 325-foot levels. Before this development had been completed it was clear that the funds immediately available made it imperative to get revenue from production as soon as possible. By the beginning of 1946, the remarkably high-grade character of the ore in the present B Shaft area had been established by surface drilling, and the decision was made to obtain initial production from this source. Since known orebodies at shallow horizons were to be developed quickly, the choice of a suitable rock outcrop for the shaft was something of a problem."

Jan 1, 1953

By Will Callupe Arzapalo

The success of the minimization of blast induced-damage at Barrick?s Pierina Mine in Peru is the result of an effective working relationship between Mine Operations and the Geotechnical Services Department. A detailed design criteria manual is used to match the blast plan to the site?s varying rock types and slope designs. The Geotechnical Services Department has further developed a comprehensive pre- and post-blast checklist that is critical to the drilling and blasting process as it pertains to wall stability. Wall control blasts are evaluated with quality assurance field checks, vibration monitoring and frequency control, video assisted performance quantification and post excavation face profiling. These detailed observations are compiled and summarized in a blast performance evaluation that is considered to be an ?Industry Best Practice?. The information and detail provided by each performance summary allows accurate blast analysis and effective design refinement.

May 1, 2006

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By Rodolfo Espinosa Gómez

"Industrias Peñoles, S.A. de C.V. – Mining Division, has initiated in the last ten years, six Mining Operations (Bismark, Tizapa, Ciénega, La Herradura, Rey de Plata, and Francisco I. Madero) and it has expanded several of their existing Operations (Sabinas, Fresnillo, Tizapa, Ciénega) one or more times.This work aims to share the experiences learned on this growing process. Some of these lessons are: 1) Project leaders must have a leadership that fosters good communication and team work; and this leadership style must come from top management. 2) A good communication must exist between the personnel from Engineering, Construction, and Operation. Also, this good communication must come from top management. 3) Starting the project with a solid Engineering Study. 4) Do not misunderstand cost with cost/benefit; always look at the cost/benefit. 5) Selecting good Contractors and good Suppliers. 6) Good training before the project commissioning is essential to reduce the learning curve period, this is even more important in areas where local people do not have any background in mining activities. 7) Recognizing that any project has a learning curve and it must be reflected on the production budget. 8) Avoid an over optimistic Mine preparation time schedule.BACKGROUNDIndustrias Peñoles S.A. de C.V.The mission of Industrias Peñoles, S.A. de C.V. (Peñoles) is to add value to non-renewable natural resources in a sustainable manner. Peñoles seeks to build long-term shareholder value; provide their customers with the highest quality products and services; maintain productive longterm relationship with their suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which it operates, and preserve the environment.Peñoles was established on 1887. It is a Mining Group with integrated Mining, Smelting and Refining operations of non-ferrous metals, and also produces inorganic chemistry materials. Peñoles is the main World producer of refined silver, metal bismuth, and sodium sulphate; Latin American leader in the production of refined gold, lead, and zinc.The Mining Group is made-up of nine mining operations producing concentrates with high gold, silver, lead, zinc, and copper contents. It produced in 2002, 365,900 ounces of gold; 52.7 million ounces of silver; 86,820 tonnes of lead; 266,000 tonnes of zinc, 11,840 tonnes of copper; with a total values of 3,780.6 million of Mexican pesos (~ $ 378.0 million U.S. Dollars)."

Jan 1, 2004

"Each and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Several factors including ore heterogeneity and harsh production environment affect the reproducibility of the reported data. Best practices of metal accounting thus prescribe that production reports be accompanied by measurement quality reports quantifying the reproducibility (a data quality metric often expressed as a relative standard deviation) of each data reported. Ignoring the irreproducibility of measurements may lead to the perception that random errors have been totally eliminated through statistical data reconciliation, which is wrong. This paper aims at explaining the full lifecycle management of reproducibility estimation from the outset at the measurement process to its reporting after having been through the statistical data reconciliation process. Indeed, the reproducibility of reported data can be obtained by performing a sensitivity analysis. Necessary conditions for obtaining a truly representative assessment of measurement reproducibility are stated. Typical levels of measurement reproducibility found in operating flotation plants are also reported. These numbers can be used as benchmarks for reproducibility levels that can be realistically expected.IntroductionEach and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Such production reports are the most expected output from a metal accounting system (MAS). The duly recurrence of this task combined with an insufficient level of automation has somehow contributed to the misleading perception that it is mainly a clerical work. However, as shown in Figure 1, a MAS encompasses way more than just a reporting system. Acknowledging that the content of production reports indubitably origin from raw measurements has important implications for how both the reports and MAS should be monitored."

Jan 1, 2016

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By Josée Dartois

En 1988, à l?instar de plusieurs états du monde industrialisé, le Québec décidait d?accélérer la cadence de l?assainissement des rejets industriels et lançait un programme intégré de réduction de la pollution industrielle visant, à la fois, les rejets dans le milieu aquatique, les émissions atmosphériques et les matières résiduelles. Ce programme fut intitulé le Programme de réduction des rejets industriels.

Nov 1, 2002

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002