Search Documents

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By Andreas Oberrauner

Content ? What is? an introduction ? Crushing technology ? Conveying in pits ? Pit-exiting strategies ? Mine Planning in IPCC ? Summary/Conclusions EHS slide ? Sandvik?s objective is zero harm to our people, the environment we work in, our customers and our suppliers ? Current EHS-figures will be added in August! Who is this? Andreas Oberrauner ? Born in Austria ? Living in Cologne (Ger) ? Mining Engineer ? Montanuniversitaet Leoben (Austria) 2000-2005 ? PhD on Mineral Processing 2008-2012 ? Sandvik Mine Planning Department ? Main task: Provide practical and efficient solutions for mining-challenges

Aug 1, 2013

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By Oliver Hall

This paper sketches the mining at Noranda as it would be sketched to a visiting engineer. It does not follow quite the usual form, but is presented somewhat along the lines of a conversation. TO give the mining at Noranda its proper perspective, it is necessary to sketch the whole picture and outline: 1. History 2. Metallurgical Problems 3. Exploration 4. Mining Methods 5. Mining Details 6. Filling 7. Pillar Extraction 8. Costs HISTORY Noranda is a relatively young enterprise, with much of the personal character of its founders woven into it. The name Noranda is an abbreviation of Northern Canada and the name has been a happy one for an enterprise based on northern resources, tenacity and courage. The discovery credit goes to Ed. H. Horne. This intrepid prospector returned again and again to his sulphide discoveries on the shores of Osisko lake and, in 1922, after ten years of prospecting, succeeded in interesting S. C. Thomson and H. W. Chadbourne in his discoveries. The early exploration by L. K. Fletcher, from 1922 to 1925, for Thomson and Chadbourne, indicated promising, but somewhat perplexing, ore conditions. Mr. E. Hibbert and Mr. H. L. Roscoe rook on the task of preparing the mine for production and building a smelter in 1926, and this difficult task in this isolated area made steady progress and the smelter was blown-in in December, 1927.

Jan 1, 1937

By Serge Ouellet

Résumé Six modèles métriques de remblai cimenté en pâte (RCP) ont été suivis durant 120 jours par l?utilisation de deux méthodes géophysiques non-destructives : la résistivité et la micro-sismique. Les RCP étaient constitués de trois résidus miniers et de deux proportions de ciment (3% et 6% en poids). En parallèle, des cylindres de RCP étaient utilisés pour évaluer périodiquement l?UCS. La résistivité augmentait quasi-linéairement de 28 à 120 jours pour tous les RCP investigués. Des variations de résistivité selon le type de résidu et le pourcentage de ciment ont été observées. Une équation empirique a été dégagée entre l?UCS, la résistivité, le temps, la densité relative et le rapport eau/ciment (E/C). La mesure de la vitesse des ondes de cisaillement a permis de dégager une équation mathématique de type exponentielle qui relie la résistance mécanique sans correction préalable par les paramètres de la recette de RCP. La réalisation de ce projet avait pour but de dégager la meilleure approche non-destructive afin d?estimer la résistance mécanique des remblais en chantier minier. Sur la base des résultats obtenus, les deux méthodes utilisées ont donné des résultats probants afin d?estimer la résistance mécanique et les deux méthodes sont donc à même d?être utilisées en chantier souterrain. Abstract Six scale models of cemented paste backfill (CPB) were followed during a 120 days period using two nondestructive geophysical methods: resistivity and micro-seismic. CPB were made up of three mine tailings and two cement proportion (3% and 6% by weight). In parallel, CPB cylinders were used to periodically evaluate uniaxial compressive strength (UCS). Resistivity was increasing nearly in straight line from day 28 to day 120 for all CPB models. According to the tailing type and cement percentage, resistivity variations were observed. An empirical equation emerged from UCS, resistivity, time, specific gravity of tailings and, water/cement ratio. The use of shearwave velocity allowed to identify a mathematical exponential equation related to mechanical strength without prior correction of the CPB?s formula parameters. The purpose of this project was to identify the best non-destructive approach in order to evaluate the mechanical strength of backfill in a mine site. On the basis of those results, both methods gave conclusive results in order to estimate mechanical strength and both methods can be used in underground operations.

Feb 1, 2008

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Tom Olsen, Tom Ohrling, Peter Taggart, Chris Martin

"North American Palladium commissioned the new concentrator at the Lac des Iles mine in the summer of 2001. The 15,000 tonnes per day mill replaced the existing 2,400 tonnes per day facility, as part of a major mine expansion.At Lac des Iles, the grain size distribution of the platinum group minerals (PGM) is bi-modal. Roughly two-thirds of the PGM are relatively coarse-grained, and often associated with fast floating copper and nickel sulphides. The remainder is ultra-fine, and locked in silicates, which poses a special challenge to the metallurgist. The previous mill typically recovered just the fast-floating mineralisation, but to achieve target recoveries, the new mill has to recover a substantial amount of the ultra-fine PGM. The metallurgical challenges associated with the recovery of fine-grained PGM in the talcous Lac des Iles ores, are described.The paper describes the approach used in circuit optimisation, and how metallurgical and operational optimisation raised palladium recoveries by more than 6% in six months, by tuning the circuit to recover some of the ultra-fine PGM mineralisation.BACKGROUNDThe Lac des Iles mine, owned and operated by North American Palladium Limited, is located about 115 kilometres north of Thunder Bay, Ontario. The mine originally opened in December 1993, and prior to 2001 included a mill capable of handling 2,400 tonnes per day of ore delivered from the nearby Roby pit.Following an intensive exploration programme conducted in 1999, and a detailed feasibility study, conducted in 2000, North American Palladium initiated a mine expansion project, the objective being to expand milling throughput from 2,400 tonnes per day to 15,000 tonnes per day. This required construction of an entirely new mill, which was commissioned in May 2001."

Jan 1, 2003

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By Louise H. Michaud

Albian Sands Energy is scheduled to begin production at its oilsands operations in the fall of 2002. Start-up includes the selection and implementation of over 75 IT systems or computer applications. These include engineering applications, systems required to control mining activities, maintenance, the processing plant and utilities, and also systems required to run the company, such as human resources, finances and inventory/warehousing. This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in Albian?s approach to identifying system requirements is the development of a Business Activity Model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been lead by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that don?t meet the company?s expectations. To ensure a more positive outcome, Albian believes that it is imperative that the company?s technical and business people are closely involved in the selection process. Integration of the IT systems is also key, including linking all applications through a Data Warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company.

May 1, 2002

By David H. Searle

This paper will discuss the common trends existing in various Canadian jurisdictions for the closure and reclamation of mines. Included will be a discussion of the requirement to post security as well as its form and how security is calculated and refunded. Reclamation can no longer be left to the end of mine life. Progressive reclamation must occur throughout mine life and must be part of the mine plan from the beginning.

May 1, 2006

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002