Search Documents

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By C. A. D' Odorico

The zinc pressure leaching (ZPL) plant at Teck Cominco's Trail Operations was started up in 1981 and represented the world's first commercialization of the technology. From the outset, the process was designed to operate using iron-rich Sullivan Mine zinc concentrate. When the Sullivan Mine reached the end of its life in 2002, the ZPL plant underwent a significant process change with the treatment of 100% Red Dog zinc concentrate. Through careful improvements to existing plant processes, controlled changes to plant operating parameters and a rapid adjustment to the modified process by operations personnel, the plant has been successfully converted to processing a feed of 100% Red Dog zinc concentrate. This paper discusses the challenges faced during the conversion and describes the modifications to plant operating procedures, as well as changes to plant processes.

Jan 1, 2004

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Neil R. Burns, Michael Doggett

Abstract - The Nanisivik mine offers a unique opportunity to examine the economics of a mining scenario from its original feasibility study through to closure. In the early 1970s, the Strathcona Sound project (exploration around the Nanisivik mine) had advanced to the point where a significant mineralized body had been defined and a feasibility study was initiated. The study supported development of the Nanisivik mine, with government investment in regional infrastructure, and the mine was constructed and operated for 26 years. Many elements of the feasibility study were difficult to estimate because the project was unique in its high Arctic setting. As a result, many differences were found when comparing the actual mining data to the feasibility study. The majority of these differences were the result of an actual mine life of 26 years instead of the planned 12.5 years. Most of the mining costs were higher than estimated and production occurred at a much higher extraction rate than planned. On a constant dollar basis, the metal prices were, on average, below the feasibility estimates. For the most part, these differences balanced out, with the actual mining being only slightly more profitable than anticipated in the feasibility study.

Jan 1, 2004

By J. Smit, F. Parada, R. Parra, E. Balladares, M. P. Merino

"In this study, a two-step process was developed for recovering copper, molybdenum, zinc and iron (hematite). In the first step, grinded slags (-65 mesh) were sulphated with SO3 at 350-500ºC to form iron, copper and zinc sulphates. In the next step, the formed sulphates were decomposed to hematite, copper and zinc sulphates and oxysulphates at 700-750ºC. The generated SO3 was recirculated back to the sulphation step. The generated calcine in the decomposition step is leached with 25 gpl acid at 50ºC to dissolve the copper, zinc and molybdenum for further conventional separation and recovery. The hematite residue, of intense red color, can be used as pigment, in the ceramic industry or as pellet feed. The fine crystalline silica remains in the hematite residue."

Jan 1, 2014

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By S. Khoshkhooei

In this research, the effects of rare earth elements addition on thermal fatigue behaviors of AZ91 alloy were studied. Repeated heating and cooling cycles were applied on the samples at 170°C and 210 °C to develop thermal fatigue cracks, Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy (SEM) as well as energy dispersive X-ray spectroscopy (EDS), Thermal fatigue behaviors were improved successively by addition of up to 2-wt% RE, This improvement is attributed to consummation of the aluminum of the melt by precipitation of the needle shape Al 11 RE3 phases, This process reduces the volume of Mg17Al12 phases and consequently decreases the brittle Mg/Mg17Al12 interfaces which are the main reason of weak thermal properties of the alloy at rather high temperatures, Further additions of RE, however, reduced the thermal shock resistance of samples by increasing in the mean length of the brittle needle shape phases.

Jan 1, 2005

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By Gaoming Wang

Outline 1. The Gangdese porphyry Cu-Mo belt 1.1 Regional geological background 1.2 Cu-Mo-bearing porphyries 1.3 Mineralization and alteration 2. Dating methods and results 2.1 Qulong porphyry 2.2 other porphyries 3. Geodynamic implications 4. Conclusions 5. Acknowledgements

May 1, 2004

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the present study, the dynamic response of AZ and AE cast magnesium alloys to shock loading, are compared for strain rates ranging between 900 and 1200 s-1. Texture measurements showed that after shock loading, the (00.2) basal texture component of both alloys was strengthened. However, the strengthening magnitude was higher for AE samples. Also, it was observed that the twinning fraction decreased in both alloys with increase in the amount of alloying elements. In addition, cracks are formed at the interface between matrix and second phase particles in the AZ alloys. However, crack nucleation and fracture in AE alloys occurred at the sites where twins accumulated. Furthermore, analysis of the dynamic mechanical behaviors showed that the ductility of AE grade is higher than that of AZ alloy for all strain rates used in this research. This difference was explained by differences in deformation mechanisms of these alloys.

Jan 1, 2014

By C. Bourgoin

"The limited development and application of new technologies to narrow-vein mining is currently impeding progress in the industry to a point where productivity, working conditions and operating costs have reached a critical stage in many Canadian mines.In an effort to foster the emergence and application of new technologies, Université Laval, together with other organizations, has carried out a R&D project focussed on the need of identifying new development pos5ibilities and of facilitating the transfer of technology in matters related to underground mining methods and machinery.The first phase of the study consisted of an in-depth assessment of current practices and problems in narrow-vein mining. The second phase was a state-of-the-art survey of mining methods and equipment, together with proposed modifications and innovations. The third phase of the project concerns the experimental development as well as the principal application of various proposed technologies.This paper presents an overview of the organizational, technical and strategic considerations which guided the University group and it serves as well to introduce a newly-published brochure, entitled ""Underground Mining Techniques of Vein Deposits"", which summarizes such work to date. More specifically, a perspective of technological developments applicable to narrow-vein mining is presented."

Jan 1, 1994

By A. Probst, J. A. Finch

"Solids concentration (weight % solids) profiles and the clear liquid/slurry interface level (mud-line) were determined from conductivity measurements in thickeners at Falconbridge's Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and a jarosite thickener in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 23 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by a sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles using a model due to Maxwell.The results from conductivity measurements were compared with direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line informnation could improve the operational efficiency of industrial thickeners."

Jan 1, 1994

By R. Bridge

Mining companies are progressively finding themselves having to develop operations for more complex, deeper ore bodies, which require the use of more complicated mining and mineral processing methods. This coupled with the generally increasing trend of higher capital and operational costs have led to a need in the industry for improving ore body knowledge, mining and mineral processing. Geometallurgy is a relatively new concept that can link the three aspects, and when used effectively it is a method that can produce the necessary information for designing and building operations for reliable and optimum performance. Geometallurgy not only involves the integration of geological, mining, and metallurgical fields, but it can also be expanded to include environmental and economic information to produce a block model that can be used to obtain the best outcome in terms of plant response and plant sustainability. The geometallurgical program should not end once the block model has been populated. A detailed geometallurgical approach should be applied to all stages of the operation encompassing sample selection, through to equipment sizing and production forecasting. It can also become a useful optimisation tool thereby allowing the operation to be proactive rather than reactive against changes in the ore characteristics. With the development of metallurgical performance predictors it is possible to quantify how the ore will behave in the process plant in terms of throughput, recoveries, reagent consumption, etc. Therefore, in terms of responsible mining and sustainable resource development, a geometallurgical approach to operations is the logical step for plant development. In this paper we describe the state of the technology with respect to the application of geometallurgical modeling and its utilisation in the fields of design, forecasting and optimisation of mining operations.

Aug 1, 2013

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969