Search Documents

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By C. J. Rockingham

"A comparative study of sulphide textures has been carried out on samples from four Archean copper-zinc massive base metal sulphide deposits: Kidd Creek, Ontario; Lake Dufault -Norbec, Quebec; Hood River-41, N. W. T.; and Geco, Ontario. These deposits have undergone metamorphic recrystallization under a range of conditions, and results of this study indicate that certain sulphide textures may be used as qualitative indicators of metamorphic grade, whereas other cannot.The sulphide textures of most value in this regard are sulphide grain sizes, which increase with increasing metamorphic grade, and the presence or absence of sedimentary/diagenetic textures, which are destroyed at the lower amphibolite facies of metamorphism. Chalcopyrite and pyrrhotite intergrowths in sphalerite increase in size, in degree of coalescence and in the ratio of unmixed pyrrhotite to chalcopyrite inclusions with increasing metamorphic rank. With increased metamorphic grade, the pyrrhotite intergrowths change from rounded inclusions on grain boundaries to rod-like shapes along sphalerite twin planes. There is also a general increase in the relative proportion of pyrrhotite in the deposits. Textures that appear to have little value as indicators of metamorphic grade are sulphide deformation textures, and triple junction point angles and their standard deviations, which show little variation from the lower greenschist to the upper amphibolite facies of metamorphism. The presence or absence of myrmekite-like magnetite also has little value in determining the relative metamorphic history of these deposits, as it is a product of local contact metamorphism."

Jan 1, 1980

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By V. Casaletto, L. Widdifield

"Equipment capable of higher production requires more sophisticated maintenance programs. Reduction in fleet size through use of modern technology requires higher utilization and greater availability.Caterpillar's maintenance control system program will display the capabilities of computer technology in a maintenance environment. Utilizing such resources will provide increased availability, lower inventory requirements, fewer last minute disasters, and lower cost per ton for maintenance. High production from premium quality equipment can only be realized by good planning and care, executed by maintenance and operating personnel acting cooperatively.IntroductionAccurate information is the key to accurate decision making. In today' s competitive industry, mines' teeter on the brink between profit and loss. Their survival will be predicated on their ability to retrieve, analyze, and formulate accurate information regarding the operating costs of mobile equipment. This paper deals with the impact of managing equipment operating costs and introduces a computerized control system designed for monitoring and controlling these costs.Caterpillar has produced several computerized modelling programs designed at taking the guesswork out of equipment selection and management. The most basic of these is Equipment Investment Analysis (E.LA.). This model compares two or more alternatives over the projected life of the machine. It deals with comparisons in the owning and operating costs of equipment, as well as, their productivity over a specified period of time.In order for a computer model to be credible as a decision making tool, it must be simple to use and the results measurable and accountable . Caterpillar has introduced several computer models to assist the industry in selecting and managing an equipment fleet. These programs allow the user to predict and monitor the operating costs and production capability of mobile equipment. They are often used in the machine selection process to select equipment which best suits a mine's long-term cost per tonne objectives. After the optimum selection is made, Caterpillar's Maintenance Control System provides an efficient management tool to monitor and verify the data used in the selection model."

Jan 1, 1992

By J. Carr

This paper discusses: (1) the need for Western Canadian coal in eastern Ontario Hydro plants; (2) design parameters-unit trains, year- 'round receiving from trains, and shipping (Great Lakes season); (3) equipment chosen-dumper-indexer, outhaul conveyor, yard belt, stacker, reclaimer, surge-bin feeders, shiploader, docking system and dust control; (4) foundation and soil conditions-dumper house, yard belt, surge bin and dock-piling-runway; (5) winter conditions- thaw shed, feeder, lump breaker, beltings (oil), and dust control and disposal; and (6) operations to date.

Jan 1, 1979

By M. Beech-Jones

The increased emphasis on the efficient utilization of capital and mineral resources has led to several new advances in the science of mineral separation. One example of a recent development is the application of high-capacity high-intensity wet magnetic separators to fine hematit e recovery by a leading Canadian iron ore producer. The iron ore recovery feasibilit , flow-sheet development, circuit operation and metallurgical performance are reviewed.

Jan 1, 1979

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By Roger D. Plouffe

In today's mining industry, it is possible to retrieve, from small-diameter holes, geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eUJOS values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today's technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or "in-situ assaying", and the use of multiple logs for better lithological and physical rock property determinations.

Jan 1, 1981

By Akira Fujisaki

"The oil crisis accelerated the change of non-ferrous metals' demand structure. Maturing societies in developed countries and preference for lighter, thinner and smaller products are eroding the non-ferrous metal industries' growth potential. Inventory-control, stockpiling and developing new demand are measures Japanese smelters have taken to cope with the changing demand.The most effective means for risk management of product demand lies in the cooperation between ore producing countries and metal consuming developed countries to assist developing countries in their efforts to ""take-off"", which in turn will bring about a surge of demand for metals.SummaryThe non-ferrous metal industry in the world is suffering its most serious slump since the war. With some of the markets of the advanced industrialized countries approaching saturation point and economized usage of natural resources and substitution growing, the possibility of a quick recovery of the demand for base metals is dim.To cope with the changing product demand Japanese producers have had recourse to such measures as strict inventory control and stockpiling for the purpose of stabilized imports. They have also tried hard for securing raw materials and promoting new field s of demand but the very core of ""risk management"" has been the diversification of line s of business to bolster and stabilize the foundation of management of the non-ferrous metal industry in Japan.To see the demand for nori-ferrous metals recover from the slump and be put on a path of solid development, we have to wait for the economies of the developing countries to ""take off"" and for its realization the economies of the developed countries must be reactivated with new growth industries playing a leading role, and the transfer of technology and money recycling must be carried out smoothly under an orderly international trade system."

Jan 1, 1983

By Pierre Giasson

"Les avantages de l'électricitéLe thème de la réunion 1982 de l'ICM District No. 2: "" Le défi des années 80 pour l'industrie minière de la Côte-Nord"" exprime trè s bien la réalité . En effet, la récession économique qui touche présentement tout le monde industrialisé, frappe de façon particulièrement sévère le marché du fer et de l'acier. Il est donc primordial pour les industries minières de la CôteNord de minimiser leurs coûts de production. Comme on sait, une bonne part des coûts de production est directement reliée à la consommation d'énergie.Si on retourne en arrière de quelques années, les prix des produits pétroliers étaient beaucoup moins élevé s que maintenant . Par exemple: A Philadelphie, en janvier 1930, le prix de l'huile no. 6 (bunker C) était de 1.22$ le baril. En 1940, le prix mondial du pétrole brut se situait aux environs de 1.80$ le baril et augmentait très lentement jusqu'en 1973. A la mi-octobre 1973, l'organisation des pays exportateurs de pétrole (O.P.E.P.) surprend le reste du monde en annonçant que le prix du brut grimpe à S.12$ le baril. .. on connaît la suite.On sait qu'au point de vue énergétique, le nord du Québec est l'une des régions les plus avantagées au monde. Malgré le fait que notre climat soit plutôt défavorable, nous sommes assurés d'une alimentation électrique à toute fin pratique éternelle, contrairement aux autres régions du globe. En effet, l' hydro-électricité ne représente que 2.S070 de toute l'électricité produite dans le monde.Une bonne partie de l'énergie consommée dans les industries minières de la Côte-Nord est utilisée pour produire la vapeur. Or, il y a plusieurs avantages à produire de la vapeur à partir de l'électricité:1. Le prix d'achat d'une chaudière électrique peut être moins de la moitié de celui d'une chaudière à carburant fo ssile.2. Le prix de l'électricité est plus bas que celu i des autres sources d'énergie disponibles dans notre région.3. Hydro-Québec offre un programme spéci al de subventions et un prix garanti de l'électricité, inférieur de 10070 à celui de tout autre combustible (1982).4. Souvent il est possible d'utiliser l'énergie hors pointe à un coût minime.S. L'espace requis pour un chaudière électrique est beaucoup moindre. Par exemple: une chaudière d'une capacité de 120000 Ibs/hre ne demande que SO pi? de plancher, c'est-à-dire un cercle de 8 pieds de diamètre comparativement à environ 600 à 700 pi2 pour une chaudière au ma zout.6. Aucun espace n'est requis pour l'entreposage du carburant.7. Aucun espace n'est requis pour la cheminée.8. Il n' y a que très peu de pièce s mécaniques, donc ces chaudières demandent très peu d 'entretien .9. Les chaudières électriques ne génèrent aucune pollution, donc on n'a pas besoin d'équipement coûteux de contrôle de la pollution.10. Ces chaudières sont extrêmement rapides. En effet, on peut passer de zéro à la production maximum en moins d'une heure si la chaudière est froide et en quelques secondes seulement si la chaudière est à sa température d'opération.11. L'efficacité de ces appareils est au moins de 9S% par rapport à 80-8S% pour les chaudières au ma zout. De plus, cette efficacité demeure la même quel que soit le niveau de production de la chaudière. Il faut faire attention ici: les manufacturiers proposent des rendements de 99% et plus, mais ceci ne tient compte que des pertes de chaleur à travers l'enveloppe, et de l'énergie nécessaire au fonctionnement de la pompe de circulation. Il faut ajouter à cela l'énergie perdue à cause de la vidange qui varie selon le type de chaudière et selon la qualité de l'eau d'alimentation.12. Ajoutons simplement que ces appareils sont très facile à opérer du fait qu'il n'y a aucun système complexe à manipuler.Cependant, il y a un inconvénient non négligeable à utiliser l'électricité comme source d'énergie: comme on ne peut pas emmagasiner l'énergie électrique, nous sommes à la merci du fournisseur."

Jan 1, 1985

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness'> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By G. J. Simandl, H. -L. Jacob, S. Paradis, G. Valiquette

"Nos travaux de terrain dans le Grenville, effectués dans le cadre d'un projet d'inventaire des gîtes de wollastonite, ont démontré qu'il existe un secteur exceptionnellement favorable à l’exploration pour la wollastonite. Ce secteur s'étend de la municipalité de Grenville jusqu'au pare du Mont-Tremblant (nord de St-Jovite). D'autres secteurs favorables a 'exploration pour la wollastonite ont été délimités dans les regions du Lac-Saint-Jean, de Shawinigan et de la Gatineau. Neuf categories litho-structurales de gites de wollastonite furent identifiées. L'importance d'un système ou vert pour la formation des gîtes de hautes teneurs fut établie. Un guide de prospection pour la wollastonite propre à la province tectonique de Grenville fut développé. Plusieurs des indices sont prometteurs et mériteraient des travaux de raise en valeur afin de determiner s'ils représentent une source de wollastonite exploitable à profit. Lac-Saint-Jean, Shawinigan and Gatineau areas. Deposits may be classified into nine categories depending on their relationship to intrusive rocks, discordant or concordant contacts with the host rocks, morphology, and major structural controls. Deposits consist mainly of wollastonite, calcite and clinopyroxene. They may contain one or several of the following minerals: feldspar, scapolite, quartz, titanite sulphides, zoisite, clinozoisite, garnet, idocrase and prehnite. Wollastonite content may reach over 70%. Some deposits are associated with graphite veins. Better understanding of the geology, combined with the proposed classification provides new exploration guide for wollastonite. Several deposits have grades of economic interest. Further work is needed to determine if any of these deposits can be exploited for profit."

Jan 1, 1990

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By D. E. Macdonald

"Approximately 2.0 million tonnes of phosphate rock is imported from the U.S. to Alberta annually and is used in the production of agricultural fertilizers. No phosphate rock is presently mined in Canada, although sources of igneous phosphate have been mined in the past. Sedimentary phosphate rock is found in nine geological units within the Cordilleran Foothills and Front Ranges region of Alberta. The Devonian-Mississippian Exshaw Formation, Permo-Pennsylvanian Rocky Mountain Supergroup, and the Jurassic Fernie Formation have the best potential f or future development. Most of the phosphate rock in Alberta is of low grade and lies within restricted land use areas. The best over-all resource potential lies in the Fernie basin area of southeastern British Columbia, in the Fernie Formation. The possibility of deep phosphate rock deposits in the plains region should be examined.Phosphate rock is mined in Idaho, Utah, Montana and Florida, and is shipped to Canadian fertilizer plants for processing. Raw phosphate rock is acidified, usually with sulphuric acid, by a wet process. Varying amounts of ammonia are added, and the fertilizer is pelletized. Future research, in western Canada, is needed in the beneficiating of low-grade ores and in the area of in situ mining. At the present time, phosphate rock sells for around US$50Itonne, and Alberta fertilizer companies probably pay in the range of C$7D-$85Itonne for U.S. phosphate rock delivered to the plant. Environmental concerns about phosphate rock processing are centred around gypsum tailing ponds, and radioactive wastes.U.S. supplies of phosphate rock are secure until the year 2000; however, by this time, the richer deposits in the U.S. may be exhausted. Alternate deposits, such as the ones in Alberta and British Columbia, might then be considered. Phosphate byproducts, such as uranium, vanadium, fluorine and rare earth elements, may help in making the processing of low-grade Canadian phosphates economically feasible."

Jan 1, 1988

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984