Search Documents

By E O. Foster

When roasting started at Giant Yellowknife Mines in 1949, it became apparent that, to prevent air and water pollution in the surrounding district, it would be necessary to collect the arsenic that was contained in the exit gases of the roaster. The arsenic collection problem was finally solved by the installation of both electrostatic and baghouse collectors. It was realized that a considerable quantity of gold-bearing dust was leaving the roaster with the exit gases. When the collection problem was solved, it was possible to measure this loss. The loss proved to be considerable and it became evident that a substantial quantity of gold could be recovered. Research programs on dust treatment began in 1958, and by May, 1960, the treatment process which is currently being followed was started in the plant. At present, the two electrostatic preci11itators, Operated at temperatures above 600°F, collect the gold-bearing dust.

Jan 1, 1963

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By N. Razavinia

Most mining and metallurgical industries produce relatively large quantities of low grade waste heat which they vent, for the most part, to the environment. To date, little is being done to recover some of this heat and transform it from low grade to a high grade energy form such as electricity. A few decades back this was also true of paper, plastics and metals. Recycling was not a prominent activity. Today, we all know that it is and that recycling is a must for sustainable development. To this end, we feel that we are now at that point in time when the recycling of waste heat to electricity must be given serious consideration. By recycling waste heat one can achieve at least one if not two of the following benefits: 1) reduction in the carbon footprint ? by improving the overall energy efficiency of a process, and 2) production of electricity at an economically viable cost. We have developed a process that captures, concentrates and converts (3 C?s) waste heat to electricity. The process comprises 3 distinct interacting units. The first unit captures and concentrates waste heat using heat pipe technology. The second unit converts some of the concentrated heat to mechanical work which can then be readily converted to electricity. This unit is based on the classical piston/cylinder engine arrangement that is widely used by consumers to power systems with compressed air, for example. The third unit of the process dissipates the heat that the engine cannot convert to high grade energy. It also uses heat pipe technology to achieve this. The combination of the 3 units forms a unique system for recycling waste heat. This paper describes the system and it presents some results that show how the system can be made to be economically viable.

Aug 1, 2013

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

This paper presents the results of research aimed at proposing new solutions in the area of belt conveyor elements. Many factors, such as energy consumption costs, and operating costs of belt conveyor elements, including belts, idlers and drives have an impact on the operational costs of conveyors. The paper presents special tests of new materials for the bottom cover of an energy-saving belt conveyor, which decrease rolling resistance. It also presents large-scale in-situ tests of a high-output belt conveyor for the purpose of simultaneous measurements of various types of conveyor belts (standard vs several energysaving types) under typical operating conditions of a lignite surface mine. Improvements in materials used for the bottom belt covers, supported by specially developed comprehensive tests of the new types of belts have provided valuable results of various proposed solutions. Since the tests of belts were done at exactly the same time and in the same operating conditions, direct comparison of the results is valid and should lead to a substantial decrease in the conveyors? drives? energy consumption, which will improve the effectiveness of belt transport and minimize its negative influence on the environment.

Aug 1, 2013

By The Staff

"A general description of the equipment, personnel and work sequence •being used in the sinking of a circular, concrete lined, 14 foot diameter shaft which at present is at a depth of 2,484 feet. Equipping, lining and sinking of the shaft is being carried out concurrently and waste is re-moved using a mechanical mucker.INTRODUCTIONTHE BUCHANS UNIT of the American Smelting and Refining Company operates a group of mines at Buchans, Newfoundland. Buchans is in the centre of the Province (Lat. 48°47'N.; Long. 56°50'W.), five miles north of Red Indian lake at an elevation of 900 feet and is accessible by 37 miles <Jf private railway which connects with the Canadian National railway at Millertown Junction, and by 47 miles of gravel highway, which connects with the Trans-'Canada Highway at Badger."

Jan 1, 1959

"The Hardy Cross algorithm offers a reliable method of solving network systems of fluid flow and has become widely used for solving water and ventilation flow networks. A limitation is that computational iterations and time to solve a network rises rapidly with the size of the model and modern detailed ventilation networks have typically grown to thousands of airways. Non-linear matrix solving methods can offer improved performance, however these are more complex and may be unstable if initial estimates are poor. This paper presents improvements that can be applied to the traditional Hardy Cross algorithm to greatly reduce iterations and solving time for large ventilation models. INTRODUCTION The Hardy Cross algorithm (Cross, 1936), was originally developed to solve water flow in city and urban pipe networks. Using principles of Kirchhoff’s electricity current laws, Hardy Cross developed an iterative algorithm for solving non-linear equations associated with network water flow. Traditional network analysis research refers to the various members of system networks as branches, nodes and meshes. This terminology has been changed in this paper to airways, junctions and loops respectively which are terms more familiar to engineers in mine ventilation. When Kirchhoff’s laws are applied to fluid networks, the following assumptions can be made: •The sum of fluid flows into a junction must equal the sum of fluid flows out of the junction.•The sum of pressure losses around any loop through a network system must be equal to zero.An iterative solution can therefore be achieved by initially guessing flow in a network, calculatingthe pressure losses around the network loops (Figure 1), and applying flow corrections using Newton’s method for each loop if the sum of the pressure losses does not equal zero. To solve the system, a loop must be defined for every segment or series of segments between a junction of 3 or more airways.The Hardy Cross algorithm has been used extensively for ventilation network analysis since the introduction of the first electronic computers (Tien, 1997), however numerous other variations and methods have since been developed through the use of matrices to solve the required system of nonlinear equations. Commonly used algorithms such as the Newton Raphson method (Brown, 1969), the Gradient method (Todini & Pilati, 1988), the Linear Theory method (Gupta & Prasad, 2000), and Coupled Network Solver (G. Danko, 2008) have found general use in fluid flow network solvers (Rossman, 2000). Despite poor and sometimes unpredictable convergence performance however, the Hardy Cross algorithm still has unique properties that make it attractive for ventilation models. Some benefits are:"

Jan 1, 2019

By Manqiu Xu, Andrew Lee, Frederick D. Ford, Cara Wercholaz

"Platinum-group minerals (PGM) typically occur in such low concentrations that quantitative mineralogical evaluation is difficult or impossible. The FEI MLA system used by Vale Base Metals Technology Development has been successfully employed to produce large PGM data sets that are statistically robust. The MLA Sparse Phase Liberation mapping routine produces false colored images that accurately document mineral textures, including intergrowths between various platinum group minerals and between PGMs and other tellurides and sulfides. MLA PGM search results can be used in conjunction with mineral chemistry to calculate platinumgroup element distribution to minerals and the MLA PGM images can be used to produce model grade-recovery curves.INTRODUCTIONThe platinum-group minerals (PGM) found in Sudbury area deposits have been extensively catalogued and reviewed by many authors including, but not limited to: Farrow and Lightfoot (2002), Cabri and Laflamme (1984; 1976) and Cabri (1981). The PGM list currently used has 12 minerals summarized in Table 1. As noted by Farrow and Lightfoot (2002), platinum-group minerals in Sudbury are dominated by tellurides, bismuth-tellurides and arsenides, with an absence of platinum-group element (PGE) sulphides or ferro-platinum alloys such as tetraferroplatinum - PtFe."

Jan 1, 2011

By N. R. Thote, J. L. Porathur, C. P. Verma

Highwall mining is a highly mechanized coal mining method associated with several advantages, such as a very high production rate (approximately 3,000 t/d) and low production costs. There is no requirement for underground support, ventilation, or blasting. Production leads to added recovery, which is otherwise lost in the ultimate pit. The use of highwall mining can bridge the gap that exists between supply and demand in the energy sector. This paper presents a brief review of highwall mining technology, including current status, analysis tools, and design techniques. In addition, it identifies important parameters from the analysis of failure case studies.

Jan 1, 2014

By M-d-N. Gagnon, P. Okono, Y. Bergeron

In the mining industry, decisions regarding the type and number of comminution tests to be completed typically rely on geologists? observations and conclusions when studying drill cores. Given that these decisions are based on visual observations, they are essentially approximate and often inaccurate from a comminution viewpoint, causing a sizeable margin of error in estimating characterization test needs. Consequently, companies are often forced to perform more tests than necessary, requiring a significant quantity of material, and accruing significant costs. Recently, a new device, called the Hardness Index Tester (or HIT), was developed, offering users a low cost in-house mechanism for estimating the comminution parameter A*b and the Bond Ball Mill Work Index at any mine site, with potential applications on fragments up to 25 mm from drill core. In late 2016, Agnico Eagle Mines Limited initiated a trial to investigate if having an HIT device installed in a core repository would make it possible to identify the different rock properties more accurately and determine the number and type of comminution tests required. The application of the HIT was not to replace the standard comminution tests, but rather to generate a high number of comminution and geomechanical parameters for the rock mass. Ultimately, the objective would be to determine the uniformity of the rock mass and, therefore, easily distinguish any potentially problematic zones. With this method, the appropriate number of standard tests could be determined, making the HIT not only an excellent complement to the standard laboratory tests, but also an indispensable device for a geometallurgical characterization. This paper presents the results from the HIT trial using samples from the Odyssey Project, which is a Mine Canadian Malartic property.

Jan 1, 2017

During the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits. However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses haw not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently am poorly doc-umented, the use of these terms is reviewed. Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco&apos;s Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delin¬eation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study. The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit by 39.27% and 45.41%, respectively, and that of the 6 m wide deposit by 12.84% and 11.55%. As the impacts of ore loss and those of dilution on the net present value am almost identical in these simulations, we could, in practice, assume a 50/50 split between dilution and ore losses in such a case. These results do no take into account the effects of local optimization measures taken at the mine production level (blasthole sampling near stope limits, etc.) The potential impacts of geological and sampling uncertainties in terms of lower NPV justify and require more systematic efforts to ensure that deposit appraisal work and feasibility studies are adequate to optimize company revenue and competitive returns to investors from mine production activities.

Jan 1, 2005

By Steven Hart

In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit. This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes

Jan 1, 2012

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986