Search Documents

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K J. F Logan, P W. Leaman, B A. Tucker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Nam San copper-gold deposit was discovered in 2011 and is a likely blind extension of the Permian age Phu Kham structurally deformed porphyry/skarn copper-gold deposit.The Nam San mineralisation is hosted within a dominantly sericite altered schist unit located to the north of the current Phu Kham open pit operation and is overthrust by an allochthonous barren cover sequence of limestone, granite and sandstone. Reinterpretation of the Phu Kham geology developed the concept of a possible telescoped porphyry copper-gold system at depth. Initial drilling intersected remobilised copper mineralisation in a basal conglomerate, confirming the concept. A reconnaissance vector array induced polarisation (IP) survey identified a deep chargeability anomaly from which a drilling target was developed from 3D inversion modelling of a detailed follow up dipole-pole-dipole anomaly. Drilling of the chargeability anomaly intersected the blind Nam San copper-gold mineralisation beneath the thrusted cover sequence.The key discovery parameters are the result of an integrated exploration program that included reinterpretation of the local stratigraphy, which developed the concept of a deep blind orebody, IP surveys capable of penetrating through the barren cover and a commitment to a deep directional drilling program to test these concepts and targets. The inferred resource remains open at depth, and further assessment will most likely be through underground development.CITATION:Leaman, P W, Tucker, B A and Logan, K J F, 2015. The discovery of the Nam San copper-gold deposit, Phu Kham, Laos, in Proceedings PACRIM 2015 Congress, pp 515–520 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J S-L Chan, J C. T Chu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. In its industrial days, Hong Kong’s mining industry was thriving, benefitting from the mineral occurrences that are related to the regional Mesozoic igneous and hydrothermal activities.Hong Kong was unique in the mining sector as it was so small in landmass but with such a rich variety of commodities discovered. There are records of commercial exploitation of tungsten, iron, lead, silver, beryl, graphite, quartz, feldspar and kaolin in Hong Kong before 1981. Of these, most of them are located in the New Territories.The Lin Ma Hang lead mine was operated in the 19th century by the Portuguese and was abandoned in 1958. The Needle Hill tungsten deposit was discovered in 1935 during construction of the Jubilee Reservoir. The Ma On Shan iron mine, which operated for 70 years between 1906 and 1976, was the largest mine in the history of Hong Kong. The Mui Wo lead-silver mine on Lantau Island can be traced back to the Ming Dynasty 400 years ago. West Brother Island, which extracted graphite from 1952 to 1973, was levelled in the 1990s to make way for the development of the airport at Chek Lap Kok.Nowadays, these mines are disused and abandoned, but this extended abstract reviews the legacy of the mining industry in Hong Kong to understand the impact that it had on techniques, the economy and culture.CITATION:Chu, J C T and Chan, J S-L, 2015. The history of mining in Hong Kong , in Proceedings PACRIM 2015 Congress, pp 109–114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

Adsorption Isotherm Measurement of Sodium Oleate on Haematite Using Differential Thermal Analysis

Sep 13, 2010

By S Winter, G Klenowski

During longwall mining in the Bowen Basin, open tension cracks formed by overburden subsidence occur to a height of about 175 m above the mining horizon. Within this zone, water in aquifers or inundated workings will flow into the mine.At the Oaky Creek mines Aquila seam, open cut pits containing pit water overlie German Creek seam longwall panels at a height of about 105 m. The highly saline water is classified as contaminated and cannot be discharged off-site. Because alternative water storage facilities were not available, innovative water management solutions were needed to allow longwall mining to proceed without underground flooding.Computer modelling and underground inflow measurements have been completed to accurately determine inflow rates into longwall mines from overlying water sources at increasing overburden heights. Research work has also included determining cost-effective blanket treatment of final voids and reshaping spoil piles to minimise downward seepage.Ponded water overlying the Aquila low, Grasstree south and A6 pits required remedial works prior to longwall undermining to prevent flooding. In the Aquila low pit it was necessary to partition the pit and remove water overlying longwall 32. Two in-pit bridges were constructed by dozing and track compacting low wall spoil. The final void above the longwall panel was kept dry during undermining. Maximum recorded underground inflow rate was 30.0 L/s.The Grasstree south pit final void, part of the ramp and much of the spoil piles were inundated prior to undermining of 308 panel. A bridge and blanket were required to prevent ponding above the longwall. Maximum recorded inflow during undermining was 23.2 L/s.The pit A6 south final void, which contained dumped, saturated rejects and inundated highwall mining entries was undermined by longwall 36 at the Oaky No 1 underground mine. Because mapping of highwall entries was not available, the maximum calculated inflow rate of 73.0 L/s was based on all design entries being fully inundated. The actual inflow rate during longwall mining ranged up to 20.0 L/s.Water management improvements that have been implemented include greater use of contaminated pit water to wash coal, use of evaporation fans, and installation of a 6 ML/day reverse osmosis plant for water purification.CITATION:Klenowski, G and Winter, S, 2017. Inflows into longwall mines from inundated overlying workings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Mnller, J L. Mauk

The Oblaga Cu-Au skarn deposit and porphyry prospect is located in the south-eastern edge of the Gobi Desert in western Inner Mongolia. The deposit occurs within metamorphosed middle Paleozoic volcanic, plutonic and sedimentary rocks.   Ivanhoe geologists recognise eight main rock types in the area. Calcareous sediments include conglomerate, interlayered siltstone-sandstone, and limestone. Covering the calcareous sediments is a slab of thrusted biotite granite, and above it is rhyodacitic lithic tuff which, in places, is overlain by alluvial sediments. Various plutonic rocks and related intrusion breccias have intruded these units. Monzodiorite, quartz-monzonite and monzonite tend to form thin, high-angle intrusions and the youngest andesitic intrusions are generally wider and subhorizontal.   The Oblaga Cu-Au skarn, which occurs in the calcareous sediments, shows typical prograde and retrograde mineralogy. Petrographic studies show that prograde skarn minerals have been overprinted by retrograde skarn minerals, and original host rock minerals have been texturally obliterated and completely replaced. The mineralogy of the Oblaga skarn deposit is very similar to other Cu-Au skarn deposits worldwide.   Sericitic and minor chloritic alteration occurs throughout the study area and may relate to porphyry-style mineralisation. Generally, this alteration is not intense and most rocks have retained their original texture. Geochemical analyses suggest that K-metasomatism is not widespread at Oblaga. XRD analyses suggest an upward and outward transition from sericitic to chloritic alteration.   Comparisons between Oblaga and other porphyry Cu-Au deposits worldwide show that Oblaga has very similar characteristics to deposits that have undergone sericitic alteration. However, Oblaga is special because it also has relatively intense chloritic alteration, which is uncommon in other porphyry Cu deposits described in the literature.

Jan 1, 2005

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By E Acu±a, B Prosser, R Alvarez, K Wallace

This paper describes the ventilation analyses performed for the access tunnels at the New Level Mine project (NLMP) at CodelcoÆs El Teniente operation outside of Rancagua, Chile. This new mine is anticipated to reach a final production of between 137 and 180 kt/d. Production from the NLMP is scheduled to start in the year 2017. The main access tunnels (MAT) are approximately 9 km in length, with one for personnel and supply access and the second one for ore extraction through a conveyor system. These two tunnels are a critical component of the initial stage 1 development and will be constructed independently of the existing mine workings. The tunnels were originally designed to be constructed with two tunnel boring machines. However, later analyses changed the construction approach to a conventional drill and blast technique. Because the design included two mid-tunnel ramp-to-surface connections, conventional mining methods would allow for development of the tunnels with multiple working faces to achieve a more rapid schedule. This paper presents the initial baseline considered for the ventilation design and the optimisation methodology applied by Codelco to minimise the airflow and pressure requirements of the ventilation system. Modifications to the design resulted in the addition of strategic airways and raises that could provide a saving of approximately 1 MW, when compared to the original design.CITATION:Acu±a, E, Alvarez, R, Wallace, K and Prosser, B, 2013. Ventilation considerations for the new level mine project access tunnels, in Proceedings The Australian Mine Ventilation Conference , pp 203-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Mitra, T Singh, D O’Dea, T Honeyands

Permeability and air flow rate in the bed during iron ore sintering is crucial to controlling the sinter quality and productivity of a sinter plant due to its influence on the flame front speed. In the present work, the permeability of the bed during sintering was analysed by means of measured pressure drop and temperature at multiple points in the bed during sintering. Three different zones were categorised, ie humidified (green) bed, region of maximum resistance (high temperature zone) based on temperature, and sintered bed. Previous work has shown that the maximum pressure drop during sintering was due to several concurrent physico-chemical processes including dehumidification, calcination of fluxes, dehydroxylation of goethite, combustion of coke and melting of granules (>1200°C). To quantify the effect of the different process, sintering experiments were conducted in a milli-pot (diameter 53 mm, height 400 mm) with pressure and temperature measured at same location in bed. The milli-pot was fitted with four equidistant (80 mm apart) taps. Overall, five sections in the milli-pot were analysed for pressure drop at different times during sintering. It was found that in region of maximum resistance, coke combustion and flux calcination were highest contributors with ~35 per cent of the pressure drop when compared to other processes like de-humidification and goethite dehydroxylation which contributed to ~20 per cent and 25 per cent each respectively. The pressure drop contribution of the coke combustion region increased with increasing coke addition rate.

Nov 8, 2021

By P Collier

From 1972 until 1989 when operations were suspended Bougainville Copper Limited (BCL, owned 53.58 per cent by Rio Tinto Limited) operated a large open pit mine and processing facility at Panguna on Bougainville Island, Papua New Guinea producing copper concentrate containing significant quantities of gold and silver.BCL has a stated vision of recommencing operations at Panguna. In 2008, Rio Tinto, on behalf of BCL, conducted a multi-disciplinary study to assess the technical and financial viability of redeveloping the Panguna operation. One of the key outputs of the study was a Joint Ore Reserves Committee (JORC) Code compliant mineral resource statement based on the existing block model and fundamental data, archived since mine closure. Historical data (including the resource block model and drill hole data) was recovered from computer archives by a former Panguna mine employee familiar with the various obsolete data formats, thus maintaining an unbroken chain of custody of the data by Rio Tinto since operations were suspended. No additional data were collected as part of this study.The extensive data and documentation archive facilitated a sufficiently detailed evaluation of the fundamental data and model to support an updated resource statement. Table 1 of the JORC Code was used to guide the model validation process.Reconciliation of blasthole and metallurgical plant data with the reserve model, indicated that the copper and gold drill hole composite database was significantly biased towards underestimation in several key domains due to a combination of the following: mineralisation loss during core loss, core loss (minor), vertical drill holes failing to intersect sufficient subvertical mineralised fractures and veins, drill hole spacing too wide, and variable diamond drill hole core size. The resource model evaluation was based on three material types (all previously mined at Panguna), that were defined based on cut-off grade and rock type parameters: direct feed ore – material for delivery directly to the plant, preconcentration and screening ore – subeconomic material beneficiated to produce fines of economic grade, and waste. Three pit shells and designs were generated based on three separate sets of economic parameters. These economic parameters were also used to assign material types to the block model. The three resulting models were then evaluated against the corresponding pit shells.Classification of the resource was approached conservatively due to the inherent bias in the drill hole data. Consequently only Indicated and Inferred resources were tabulated.The study highlighted the importance of maintaining detailed documentation pertaining to resource estimates and operational history, particularly reconciliation, and the value that can be added by a simple, low-cost data compilation exercise.

Aug 22, 2011

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B Rusk, L Corriveau, P Emsbo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Porphyry-Cu (Mo-Au) deposits and iron oxide-copper-gold (IOCG) deposits are both characterised by the presence of abundant halite-saturated fluid inclusions that reflect the circulation of hyper-saline hydrothermal brines. While it is widely accepted that brines involved in the formation of porphyry copper deposits derive from unmixing of moderate-salinity, intermediate-density fluids that exsolve from crystallising magmas, the source of brines that form IOCG deposits remains enigmatic and intensely debated. In this extended abstract, we summarise the fluid inclusion characteristics of both deposit types and present trace element compositional data for halite-saturated fluid inclusions from both porphyry copper deposits and IOCG deposits from around the world.While both deposit types typically contain halite-saturated fluid inclusions, vapour-rich fluid inclusions in IOCG deposits are less common than in porphyry deposits and evidence for fluid immiscibility is rare. IOCG deposits also typically lack intermediate-density fluid inclusions that characterise the deeper quartz-rich veins in many porphyry deposits. Many IOCG deposits contain CO2-only fluid inclusions, a type of fluid not observed in porphyry Cu deposits.Our fluid inclusion compositional data show that most porphyry Cu (Mo-Au)-related brines are dominated by Na, K and Fe and contain elevated concentrations of Ca, Cu, Pb, Zn and Mn up to around the one per cent level. On the other hand, IOCG brines are Na-Ca-Fe-dominated and typically contain far less Cu, Mn and Zn than porphyry brines. In addition to Ca, these fluids are also strongly enriched in Ba and Sr relative to porphyry-related brines. Such compositions are consistent with extensive fluid-rock interaction and/or an evolved sea water contribution to IOCG brines.A sea water or basinal brine source for IOCG brines is further supported by bromine concentrations that are much higher than is characteristic for porphyry-related brines. Porphyry brines have Cl/Br molar ratios of between 800 and 3000, which is characteristic of primary magmatic brines, whereas the Cl/Br composition of IOCG brines is more variable. For example, Na/Cl/Br ratios of most IOCG deposits in the world-class Carajás district fall on or near the sea water evaporation curve (most Cl/Br molar ratios are between 200 and 1000) and are diagnostic of sedimentary bittern brines. A few of the deposits in this district also show evidence of the input of subordinate amounts of magmatic brine. At Ernest Henry, in the Cloncurry district of Australia, most Cl/Br ratios plot close to the sea water evaporation curve, but Cl/Br ratios of up to ~5000 in several samples suggest the input of lesser amounts of magmatic fluids, and possibly evaporite-dissolution-derived fluids. Taken together with geologic constraints, these data strongly suggest that porphyry-type deposits form from the circulation of dominantly magmatic fluids, while IOCG deposits form from large-scale circulation of high-salinity fluids sourced dominantly from sedimentary basins with variable input of magmatic volatiles.CITATION:Rusk, B, Emsbo, P, Xavier, R P, Corriveau, L, Oliver, N and Zhang, D, 2015. A comparison of fluid origins and compositions in iron oxide-copper-gold and porphyry-Cu (Mo-Au) deposits , in Proceedings PACRIM 2015 Congress, pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E Villaescusa, C Drover

Fully resin encapsulated threaded bar and cement grouted cable bolts are common forms of reinforcement for underground mining excavations constructed at great depth. These elements are frequently installed to dissipate the dynamic loads caused by violent rock mass failure mechanisms. Failure of the ground support scheme without rupture of the reinforcement elements implies that the maximum energy dissipation capacity of the scheme was not utilised. The ground support damage mechanisms are useful to identify in this context as they reveal vulnerabilities which limit the scheme performance. This paper presents a number of field observations of reinforcement performance following a range of dynamic loading conditions. It was observed that fully resin encapsulated threaded bars exhibit variable behaviour. In particular, inconsistent resin encapsulation was frequently observed in combination with surface support failure, indicating that the retention function of these elements may allow preferential loading of the surface support system. Observations of cement grouted, twin-strand plain cable bolts reveal a common mode of damage involving differential displacement across the steel-grout interface and slip of the cable within the borehole. This is common where strands are not mutually tensioned with barrel and wedge assemblies. Surface fixtures that exceed the strength capacity of the cable strand are required in order to minimise the occurrence of this response. Improved load transfer from the rock mass and surface support to the cable can thus be achieved, particularly where small block size failure occurs.CITATION:Drover, C and Villaescusa, E, 2016. Field performance of fully encapsulated reinforcement during violent failure events, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 659–668 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By P Holtham, K Duffy, W Valery, A Jankovic

As high grade ore deposits are depleted, remaining deposits are generally lower grade and require the mining and processing of larger volumes of material per tonne of product. These low grade deposits often contain a large proportion of barren gangue. Pre-concentration aims to remove this barren material at as coarse a particle size and as early in the process as possible. This has the potential to reduce processing costs, energy and water consumption, increase production and improve resource utilisation.There are several technologies that may be applicable for pre-concentration. This paper looks specifically at bulk ore sorting and how it can be integrated into existing or new mining operations to improve profitability and reduce environmental impact. Bulk ore sorting is the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor measurement. It may be used to increase the production rate through fixed plant capacity, or increase production and/or reduce the size of downstream processing equipment in Greenfield operations. Marginal ore sub-economic reserves may be upgraded, making them economic to treat and improving the resource utilization. Bulk ore sorting could also be used to reduce dilution and ore loss in mining operations by improving grade control, or to separate ore types to treat via different process routes. Various applications of bulk ore sorting are discussed in this paper, and three cases are investigated considering the impact on the overall operation and the associated benefits.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Integrating bulk ore sorting into a mining operation to maximise profitability, in Proceedings MetPlant 2015, pp 273–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997

By K Peters, C McKenzie

New Zealand has an established history of gold production beginning with the gold rushes of the 19th century in the Coromandel, Nelson/Marlborough, West Coast and Otago regions. Despite this, the number of significant modern hard rock gold operations has been limited in recent years due to a lack of sustained exploration capital and not limited geological prospectivity.The New Zealand Government is actively encouraging explorers to invest in New Zealand through a series of targeted promotional visits, more importantly through the acquisition of precompetitive regional geophysical data. Data collection has been completed over the prospective Northland epithermal district and a large portion of the South IslandÆs west coast that is prospective for both orogenic gold and intrusive related gold.Analysis of new data has been an important component in aiding the generation of exploration targets from prospectivity modelling. Determining the prospectivity of an area involves reviewing all the available data and analysing it with respect to the most up-to-date mineral system model for the mineralisation style of interest. Using the weights of evidence modelling approach, the most prospective areas for epithermal gold-silver, orogenic gold and intrusion-related gold have been identified. The key exploration parameters relevant to each mineral system are first represented spatially and then statistically combined into a single prospectivity map. New potentially economic deposits could be found by focusing exploration on targets identified from these models. The prospectivity modelling approach can greatly reduce the risk involved in mineral exploration.CITATION:Peters, K and McKenzie, C, 2013. New Zealand gold potential - using mineral prospectivity modelling to evaluate gold-bearing mineral systems in an underexplored country, in Proceedings World Gold 2013 , pp 479-486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D Craw, C Smith, C Martin

The Wangaloa coal mine closed in 1989, and an attempt to grow Pinus radiata on quartz-rich overburden dumps was not successful. The site is currently being rehabilitated with re-profiling and native plant establishment. Plants are being established in a range of substrates that consist of variably disaggregated Tertiary coal measure sediments derived from the mine sequence. This material has low organic matter content (typically <10 %), originating from coal fines or carbonaceous sediment. Substrate samples were collected during December 2003 from a range of sites varying in age, slope, and parent material. Nutrient analysis includes nitrate, ammonia, total N, total P, available P and readily exchangeable base cations. Total nitrogen and phosphorus are low on areas of recently disturbed, quartz-rich overburden, with total N =1200 mg/kg, and total P =200 mg/kg. Background forested areas have total N ranging between 2800 - 3300 mg/kg and total P of 420 - 500 mg/kg. Quartz-rich overburden sites contain available nitrogen levels of less than 6 mg/kg, while background forested areas are generally >20 mg/kg. The soils and water runoff are generally acid, with pH down to three. Water samples have been collected from both ground and surface resources on a monthly basis since December 2003. The main lake on the site had pH of 4.6 in 1999, and this remained relatively unchanged when 850 tonnes of lime were added in 2002. However, the lake pH changed to 6.4 within a one month period in 2004, and has fluctuated since that time.

Jan 1, 2004

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011