Search Documents

By D J. Black

The process of longwall coal extraction coal causes fractures in the overlying and underlying strata and these fractures become pathways for gas released from adjacent coal seams to flow into the mine workings and contaminate the ventilation air. If the rate of gas emission exceeds the diluting capacity of the ventilation air, the gas concentration will increase and exceed the statutory limit resulting in production delays.All potential gas sources within the planned mining area, including coal seams located above and below the working seam, should be identified and sufficient gas data collected and used to determine the specific gas emission from each gas source. Gas reservoir and emission modelling is recommended to determine specific gas emission and changes in gas emission from individual sources over the planned mining area. Accurate gas reservoir and emission modelling provides the information required to accurately design gas drainage programs to effectively manage gas emissions and minimise the risk of ‘gas-outs’.Given the increasing occurrence of incidents of gas concentration in ventilation air exceeding the 2.0 per cent statutory limit and changes to mine plans to avoid ‘difficult-to-drain’ areas, it is apparent that many operations are not effectively utilising gas reservoir and emission modelling to identify high gas emission areas and are not completing sufficient gas drainage in advance of planned mining.The process of gas reservoir and emission modelling to support gas drainage design to control tailgate gas concentration and fugitive emissions is presented and discussed.CITATION:Black, D J, 2017. Gas reservoir and emission modelling to evaluate gas drainage to control tailgate gas concentration and fugitive emissions, in Proceedings Australian Mine Vent Conference 2017, pp 65–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Slime Flotation Using Ethoxylated Surfactants in Solutions of the Electrolytes

Sep 13, 2010

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006

The long-term outlook Tor Australla's traditional mining products is for flat demand and continuing low prices. This has come about because of three far-reaching changes since earlier boom days: 1. Continuing declines in intensity of usage of basic mine products; 2. The failure of newer western and third world developing countries to realise growth expectations; and 3. Continued production pressure from third world countries (and first-world primary producers) in an effort to earn foreign exchange and rectify trade balances. These trends have led to a general situation of excess supply and weak demand. In this environment, the prerequisites for survival in the mining sector are first-class mines, modern and efficient production methods, low unit costs, aggressive marketing, and products with reasonable operating margins. Many of Australia's mines meet these prerequisites. Following the A$ depreciation and widespread unit cost reductions, most of these mines will be moderately profitable at current depressed commodity prices. They are well placed to benefit from price rises if these eventuate. A new generation of mines is concentrating on a more profitable product range (gold, diamonds, uranium, mineral sands). Australia's balance of trade remains firmly dependent on the primary mining and agricultural industries (Fig. 1). Despite optimistic talk of high-tech developments, tourism and a resurgence of manufacturing, these will remain a small component of Australia's export structure.

Jan 1, 1987

By P de Caritat, A Davidson, A Mann

Top outlet sediments from the National Geochemical Survey of Australia have been extracted by a partial extraction method for over 50 elements including gold. The partial extraction results from this low-density survey show discrete coherent anomalies for Au in the vicinity of many of AustraliaÆs known goldfields, and in the vicinity of some minor gold occurrences. In several instances catchment outlet anomalies for Au have been recorded from areas not known to contain significant economic gold. Several large economic goldfields are shown to not produce anomalies in catchment outlet samples. A survey of overbank samples in the Swan Avon catchment of Western Australia at double the sampling density shows that low level anomalies (>1 ppb) can be traced back to source using overbank sediments. Follow-up of one of the Au anomalies at Kent River in previously regarded non-auriferous terrain (western Albany-Fraser Belt) indicates a non-economic, but perhaps geochemically significant, Au anomaly with associated pathfinders including palladium. This may indicate that further exploration of the western part of Albany Fraser Belt for Au is warranted. The combination of catchment overbank samples and partial analysis technique has been shown to be effective at locating the source of gold anomalies from initial low-density continental and regional surveys.CITATION:Mann, A, Davidson, A and de Caritat, P, 2013. High resolution soil geochemistry for gold exploration at the continental, regional and prospect scale, in Proceedings World Gold 2013 , pp 167-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M Humphreys

Multi-episodic mineralisation is often characterised by different spatial trends exhibited by different generations of the mineralisation. The structural complexity of mineralisation together with the heterogeneous nature of the mineralised zones prevents unambiguous application of the conventional deterministic methodology for 3D constraining of the mineralised domains (ie conventional wireframing is ambiguous).A different approach, discussed in the present paper, includes a probabilistic definition of the domains encompassing one statistical population of the data. The domains are defined geostatistically using the indicator probability model. An indicator threshold is chosen for the definition of the high and low-grade domains. The spatial distribution of this indicator is then modelled by a variogram. The probability of exceeding the given grade threshold is than estimated by ordinary kriging for each modelled block. Blocks are then grouped according to their probability of exceeding the threshold and a continuous closed volume (domain) created from this likely patchy grouping using an appropriate structural model to fill the gaps). Methodology for the geostatistically assisted domaining is discussed in the paper. It is suggested that this technique represents an additional tool facilitating a structural interpretation of the mineralised zones.After the geostatistical domaining of the lode has been completed the grade within each of the domains is modelled using Uniform Conditioning method. Application of Uniform Conditioning for modeling the grade distribution has a significant advantage over linear methods (such as inverse distance or kriging) because Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density and are unable to be estimated directly.

Jan 1, 2002

Predicting Flotation Response from Liberation Information

Sep 13, 2010

By N H. S Oliver

Five major veining events have been identified within the area surrounding the Mount Whaleback microplaty hematite deposit. These veining events can be directly correlated to the established deformation history of the Hamersley Province (Brown et al, in press). Vein formation temperatures of 203 to 231¦C have been obtained from primary fluid inclusions within veins which formed around the postulated time of ore formation. Preliminary proton induced x-ray emition (PIXE) analysis of these inclusions indicates KCl is the dominant salt species with varying levels of Ca, Fe, Ti, Mn present. It is suggested that some of these veins may have formed from feeder or effluent fluids from microplaty hematite ore formation.

Jan 1, 2002

By C Lutherborrow

The Sangdong Tungsten/Molybdenum Deposit is located in the Republic of Korea and was discovered in 1916. At this time Korea was a colony of Japan. It was mined for two years after discovery closing in 1918. Full production recommenced in 1933, and from that point until 1945, it was the major source of tungsten for armour plate for the Japanese military. After World War 2 the US government ran the mine until late 1946. The mine operation then passed to Korean ownership but production ceased during the Korean War and did not recommence until late 1953. The mine ceased operation in 1992 due to low metal prices. From the late 1960s to the time of closure, Sangdong was the largest tungsten mine in the world (Kim, 2002). An understanding of changing mining methods over time has been critical in assessing the potential of redeveloping the Sangdong Deposit.

Aug 22, 2011

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Hapugoda, A Poliakov, E Donskoi, L Lu

A significant amount of metallic iron in the world is produced in blast furnaces from iron ore pellets. To control the quality of pellets and to optimise pellet production, characterisation of both green and fired pellets is required. Optical image analysis (OIA) allows identification of different minerals, binder, remaining fluxes and porosity within pellets.For proper identification of the mineralogy, porosity and texture in pellets a high magnification is required, therefore each individual image covers only a very small portion of the pellet. At the same time the characterisation of pellets requires that the whole pellet is represented as a single object, so the size of the resulting overall image at high magnification can make it difficult to handle. A solution to this problem has been implemented within the CSIRO OIA package Mineral4 by combining images at different levels. Namely, to average out local irregularities, individual frames can be stitched during imaging into larger MosaiX images. Mineral4 further combines these MosaiX images into a single panorama image of the whole pellet.The proposed procedures allow the calculation of mineral and porosity spatial distributions, local gradients and abundance graphs based on the distance from the centre of the pellet. The ‘Pellets’ module of CSIRO OIA software also allows for characterisation of large irregularly shaped particles of lump ore and sinter.CITATION:Poliakov, A, Donskoi, E, Hapugoda, S and Lu, L, 2017. Optical image analysis of iron ore pellets and lumps using CSIRO software Mineral/Recognition, in Proceedings Iron Ore 2017, pp 583–592 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Thermal method of diagnostic as a nondestructive monitoring is based on data logging of infrared radiation from heated surface or from the associated thermal field. Monitoring of gearcases and motors hidden faults, such as, bearing degradation (deep-seated wears and tears, fretting wear, spalling and jamming solids of revolution) is closely related to high variations in temperature. The use of portable thermal imaging devices provides considerable advantages due to: easy remote access to the unit under test even when it is operating; minimum time required to obtain information and an opportunity for a real-time diagnosis of the tested subject's condition.

Dec 6, 2010

Copper Recovery from Printed Circuit Board by Carbonisation

Sep 13, 2010

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A Gerson, S Miller, R Smart, J Thomas

Environmental Geochemistry International (EGi) and the Ian Wark Research Institute (IWRI) collaborated in a three-year Australian Minerals Industry Research Association (AMIRA) research project (Project Number P387A) focussed on the prediction and kinetic control of acid mine drainage. As part of this project, single addition, and sequential net acid generation (NAG) testing was carried out on sulfide mineral samples. The test samples comprised a range of synthetic waste materials prepared using a quartz bulk and controlled quantities of the commonly occurring sulfide minerals; pyrite (FeS2), pyrrhotite (Fe7S8), arsenopyrite (AsFeS), chalcopyrite (CuFeS2), chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), galena (PbS) and sphalerite (ZnS). NAG test results clearly show that there are significant differences between the acid forming potential of sulfide minerals. The NAG test results for each mineral were compared with theoretical acidity values (NAPP*). The NAPP* calculation was based on stoichiometric oxidation reactions assumed for each of the sulfide minerals. Sequential NAG values for pyrite corresponds closely to predicted NAPP* values, confirming the assumption that pyrite oxidation occurs according to the stoichiometry assumed. For the pyrite sample with 5 wt per cent S, two NAG stages were sufficient for all of the sulfur to be released to solution. Since sulfides in waste materials will generally be dominated by pyrite, results also confirm the validity of including NAG testing for ARD evaluation of most waste rock. NAG testing confirms that of the sulfide minerals examined, only pyrite, pyrrhotite, arsenopyrite and chalcopyrite are acid producing, ie able to produce leachate with a pH less than 4.5. In the case of sphalerite, galena, bornite, chalcocite and covellite the pH of the final NAG solution was greater than 4.5. The significant differences between the acid forming potential of different sulfide minerals could lead to overestimation of acid producing potentials based on NAPP values calculated from total per cent S alone, ie assuming all S is present as pyrite. The oxidation of galena during the NAG test resulted in the consumption of acid. The examination of the galena surface by X-ray photoelectron spectroscopy (XPS) after oxidation in peroxide solution indicated the presence of polysulfide. The reaction of sulfide to polysulfide is acid consuming, thus explaining the net acid consuming behaviour of galena in the NAG test. This reaction pathway may provide a possible explanation for the lower than expected acid production observed for some of the other sulfide minerals examined.

Jan 1, 2003