Search Documents

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987

Thermal Processing of Petroleum Fly Ash for Vanadium Recovery

Sep 13, 2010

By Leggate J

In the past many coal mining projects commenced without any consideration being given to eventual site rehabilitation. Now that site rehabilitation is assuming greater importance with changing community expectations, and standards are becoming less negotiable, it cannot be ignored in either the development of mine working plans or economic models. The "unspecified" rehabilitation measures associated with many existing projects will be the subject of debate for some time to come yet. It would be wise to plan for the future. Once an agreeed standard of rehabilitation is accepted, good management involves considering practices which will facilitate eventual rehabilitation at least cost. Without planning for rehabilitation, many mines have adopted practices which are likely to result in very expensive rehabilitation measures and impact significantly on the overall profitability of the ventures. With adequate planning, procedures can be developed which achieve the same short term goals without significantly effecting cash flow but with very significant impacts on the final rehabilitation cost. This paper looks at the disposal of tailings and overburden in the coal mining process. The industry has in the past had an obvious preference for the "perceived" cheaper procedures for waste management such as wet disposal of tailings and high dumping of overburden. There are alternatives. The paper discusses the principles which should be incorporated into tailings and overburden disposal systems and identifies viable alternatives.

Jan 1, 1991

IN the course of his employment the Broken Hill Co. the writer has had occasion to use and instruct others in the use of the Shamrock rescue apparatus. This paper deals with the various types of apparatus tested. The common object of the various types of breathing apparatus is to enable the wearer to remain and work for varying periods of time in an atmosphere which is either deficient in oxygen or is poisonous that is, contains carbon monoxide or irritating and irrespirable vapours, such as the smoke from underground fires, sulphur dioxide or ammonia fumes. For any apparatus to be efficient as required in the above paragraph it must fulfil the following conditions;1. Air-tight as regards the passage of the air from the outside to the inside. In atmosphere containing carbon dioxide a slight leak would not render the apparatus useless; but where irritating vapours, such as the smoke from burning oregon and sulphides, are met with, even the slightest leak must be avoided.2. The oxygen supply must be ample, and so supplied that it is not checked by expiration.3. Expiration and inspiration must not be retarded.

Jan 1, 1911

By Lye GN

Rock mechanics investigations have shown that some major slopes in the Panguna pit would be stable at angles in excess of 500 providing near-surface instability could be controlled. Excavation of final batters at angles between 55¦ and 60¦ is now being carried out using D10 dozers with berms at 45 to 60 m centres. A trial slope with berms at 90 m centres is planned. Shotcreting of weak zones combined with crest reinforcement, with rock anchors and dowels, is used to provide protection against erosion and toppling of the crests. Overall slopes excavated in this way are of the order of 10¦ steeper than slopes obtained by blast and shovel excavation.

Jan 1, 1986

During the development of Lorca tunnel project in the South-East of Spain, an in-site study has been done, with the purpose of obtaining the characteristics of the different lithological units through twenty-two parameters for the design of the tunnel excavation and support. In the paper both the different works developed and the different methods and criteria followed in the obtention of the parameters are described. The values of those parameters may be useful in similar cases. Also a summary-table of the parametrical characterization for the use in similar studies is given.

Jan 1, 1987

Alternatively are they a necessary evil'? Exploration geologists are a much higher profile group but then again the higher they are the bigger they Bill. At a mine site they are reluctantly being accepted as equals by mining engineers given the requirements of the `Code' in the reporting of Ore Reserves. How best can mining geologists service their customers? Are more revealing questions to be answered in who are their customers? In the past mining geologists lived isolated existences pouring over plans and sections, now with user-friendly software packages available and the use of LAN, mining geologists and mining engineers talk electronically - God forhid what the future might hying - they might even talk to accountants and metallurgists!

Jan 1, 1997

Cobar Mines Pty. Limited (CMPL) uses sodium sulphite as the principal depressant to attain selectivity in copper flotation prior to sequential recovery of lead and zinc. The usage of sodium sulphite is examined both from a theorectical viewpoint ana from the manner in which the copper circuit at (MPL has developed. The results of relatively recent investigations, both in the laboratory ana the plant, are discussed aria shown to support the present operating Techniques.

Jan 1, 1983

By R Trueman

An improved ability to predict dilution for narrow vein deposits enables more accurate economic comparisons between mechanised longhole stoping and other narrow vein mining methods, as well as reducing uncertainty surrounding dilution estimates for deposits at the prefeasibility/ feasibility stage. This paper proposes narrow vein dilution prediction and minimisation strategies for both greenfield sites and operating mines, respectively. The narrow vein dilution method (NVD method) is a tool for more accurately predicting longhole narrow vein dilution. The method is based on a new concept called benchmark stoping width. Benchmark stoping width is based on probabilistic analysis of overbreak distributions from a typical longhole narrow vein mine. The premise for the NVD method is that dilution associated with longhole stoping can be predicted using the benchmark stoping width. In addition to dilution prediction, the NVD method also includes strategies for narrow vein dilution minimisation generally, including; filling, cablebolting, stress relaxation, extraction sequencing and blast overbreak.

Jan 1, 2008

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

By F De Beurs, S Davies

With the emphasis on CO2 emission legislation and the increasing price of traditional fossil fuels like coal, oil and gas, the use of alternative fuels is becoming more and more attractive for the industry, particularly for the cement industry. The variety of materials burnt in the kiln is enormous and varies from tyres, to animal meal and other waste material or by-products that would otherwise end up in an incinerator or landfill facility. This wide variety in materials demands thorough analysis to determine what elements are present in the organic matrix. The elements present may have an influence on the process or the quality of the cement. Toxic or environmental unfriendly elements may be incorporated or dissolved in the clinker phases; whereas volatile components may be present in stack emission to the atmosphere. X-ray analysis is already the key to elemental analysis in cement production, and is used here to determine the composition of these alternative fuels. The XRF spectrometer configuration used in this study is designed to overcome the difficulties associated with the analysis of strongly varying light organic matrices containing heavier elements in minor and trace-level quantities. Heavy element specific excitation conditions and three-dimensional polarised optical geometry increased the signal to background ratio and improved detection limits compared to conventional XRF spectrometers.

Jan 1, 2008

By P Campi, M Dodds

The EastLink project is a 39 km tollway to the east of Melbourne and includes twin three-lane 1.5 km driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley to help preserve the unique flora and fauna in the area. This paper describes the process of transferring the support requirements from the ædrawing boardÆ to the tunnelling face by integrating the temporary support design with the contractorÆs tunnel excavation and support procedures, including sharing of responsibility between the designer and contractor for selection of the support type and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. The methods developed during the design phase incorporated a formal system of reviews, support selection and feedback by monitoring tunnel and ground responses. During construction, the process was implemented using a set of simple documentation and regular structured communication between the contractor and the designer.  

Jan 1, 2008

Kinetics of bubble-particle interaction, surface hydrophobicity and interfacial phenomena in sulfide mineral flotation are discussed in this paper. Results of the measurements of a bubble and mineral induction time (IT) and detachment force (DF), vacuum of bubble evolution (VE) and mineral floatability are discussed for pyrite, galena, chalcocite and chalcopyrite. Natural wetting and wetting induced by xanthates with different lengths of alkyl chains are examined. Experiments show the existence of several maxima of hydrophobicity on dependences of pH and electrochemical potential. These maxima are attributed as the reflection of mineral surface heterogeneity due to xanthate adsorption and the presence of cationic and anionic centres with uncompensated positive and negative charges. These charges can be neutralised by both regulation pH and applied potential. The aim of this paper is to evaluate a thickness of the rupturing film and to estimate how long the bubble-mineral interactions are according to the experimental values of IT, in order to develop a procedure for comparing of the results of DF and atomic force measurements in the same dimensionality, and to compare the results of the experimental studies on the wettability of sulfides with those predicted by the models of physics of capillarity.

Jan 1, 2005

By Davies L, Jeffreys J

The Broken Hill Proprietary Company Limited (BHP) has been successfully using mini computers in its open cut strip and pit coal planning for the past six years. A recent development within the computerised Seam deposit User oriented Mine Planning System (SUMPS) provides the facility for the generation, evaluation, and simulation of colliery workings.Existing computer programs for collieries were studied, but none met the requirements of BHP's underground mine planners.Consequently, it was decided to develop programs, based on those existing within BHP for open cut strip and open cut pit mine planning. The new planning facility was designed to enable any number of proposed colliery developments and operating plans to be evaluated against optimistic, most likely and pessimistic geological lease area interpretations.In mine planning, sensitivity studies should be conducted to determine the likely effects on production, development costs and colliery economics of changes in mine design and budgeted equipment productivity. By automating the manual calculations involved, the computer programs provide the ability to conduct numerous and extensive sensitivity studies. Hence an optimum mine design for budgeting purposes can be derived quickly with an improved degree of confidence in the long term viability of the proposed development.

Jan 1, 1982

BHP Billiton Mitsubishi Alliance, or BMA, is AustraliaÆs largest coal miner and exporter, and is currently responsible for around a quarter of AustraliaÆs total annual coal exports. BMA and its predecessors have been part of the Queensland mining scene for around 40 years, developing world-class mines, a port, overseas markets, and an international reputation for quality and reliability. From its production base in QueenslandÆs Bowen Basin, BMA produces a broad suite of coals which are supplied to 73 customers in 24 countries. BMA was formed in June 2001 as a partnership between BHP Billiton and Mitsubishi Development Pty Ltd, under which the two companies share equal ownership and management of eight Central Queensland coal mines û Goonyella Riverside, Broadmeadow, Peak Downs, Saraji, Norwich Park, Gregory, Crinum and Blackwater û and the Hay Point coal export terminal near Mackay. This case study focuses on Peak Downs Mine, which was the second largest open cut mining operation to be developed in the northern Bowen Basin for the original CQCA Joint Venture. The first coal was mined in April 1972 and today, Peak Downs has a production capacity of over nine million tonnes of coking coal per annum. The mine is located 30 km south of Moranbah and 195 km south west of the Hay Point port facilities. Coal is mined by open cut mining methods using six draglines and two truck/shovel stripping fleets for overburden removal. Coal seams are mined using excavators and front-end loaders and 210 tonne capacity coal haulers.

Jan 1, 2007

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

By R P. Langford, T A. Moore

Over the last 15 years Indonesia has experienced a surge in coalexploration, which has led to the development of a major export industry. This coal exploration has improved the understanding of the geology of the Indonesian coal deposits. The main economic coal deposits are of Eocene and Miocene to Pliocene age, which mainly occur in Kalimantan and Sumatra and were formed from peat deposits in an equatorial paleoclimate similar to that prevailing today. Some of these peats were domed peats, which grew above the normal water tables, under a climate of year-round rainfall; these peats grew above the level at which waterborne mineral matter can enter the system, resulting in low ash and sulphur, and locally very thick coal. It is believed that such peats have formed the unusually thick, low ash, and low sulphur Miocene coals of Indonesia. Coal deposits of Eocene age are typically characterised by thinner seams, with relatively higher contents of ash and sulphur. The Miocene coals and Eocene coals both appear to have formed in lacustrine, coastal plain or deltaic depositional environments, similar to the modern peat-forming environments of eastern Sumatra and parts of Kalimantan. The Eocene coals formed mainly in extensional tectonic settings. Miocene - Pliocene coal deposits formed in a range of tectonic settings.

Jan 1, 1999

In this paper, a subtle, but important, difference has been drawn between responsibility and mandate. Responsibility has a connotation of financial involvement assigned to an organ- isation as a result of some action it takes, the ramifications of which can be ascribed directly to the organisation. In contrast mandate relates to the power and authority to act. The paper outlines the role of poli- ticians as community decision-makers and the need for Government policy to be flexible in an advanced industrial society so that decision- making options are kept open for as long as necessary. Further, broad community objectives need to be understood and defined so that plans and policies can be consistent. Co-ordination through communication at all levels, especially at the public administration interfaces and with the private sector,is essential for effective resource allocation and efficient implementation. The paper discusses several aspects of the infrastructure responsibility question and some considerations which might be viewed as important by the community decision-makers in considering what responsibility the "community" should accept in providing infrastructure.

Jan 1, 1974

By Barnett J. C

The arid and semi-arid region of Western Australia occupies about two-thirds of the State equivalent to an area of about 1.8 million sqkm. Groundwater demand in this area has historically been linked to the pastoral andmining industries commencing with the gold discoveries in the Eastern Goldfields some 100 years ago. Substantial increases in demand have occurred in the past two decades initially as a result of nickel discoveriesin the early 1970's and more recently the rapid resurgence of the gold mining industry. Mineral exploration and development in the Great Sandy Desert at Telfer (gold) and Kintyre (uranium) and in the Great Victoria Desert at MulgaRocks (uranium) has also been accompanied by detailed groundwater investigations.

Jan 1, 1988

By A D. Ferreira, A E. C, A D. Padovezi

The increasing market requirements regarding the quality of products, the enhanced predictability from detailed mine planning, the need for process consolidation and upgrading require continuous investigation on the characteristics of different ore types to be concentrated. This paper addresses the mineralogical and technological characterisation of several itabirite iron ore types and the influence of the composition and mineralogical associations on desliming and flotation. Pellet feed quality and the influence on the major performance indicators, such as weight recovery of slimes, selectivity index, metallurgical recovery, flotation kinetics of iron minerals and gangue is also emphasised. The investigation resulted in a classification of iron ores according to their mineralogical composition, morphology of the crystals, and/or texture and microstructure of mineral particles with respect to desliming and flotation performances.

Jan 1, 2005