Search Documents

By Das S. C

A detailed study was undertaken on the effect of Fe+3 in combination with LIX64N during copper electrowinning from sulphate electrolytes. The results show that the presence of Fe+3 not only affects the current efficiency during copper electrowinning but also affects the cathode quality. The effect is enhanced by electrolysis parameters like temperature, circulation rate, current density, etc. No significant effect was found from the presence of Fe+2. The presence of Fe+3 along with LIX64N causes a synergistic effect and results in a drastic fall in current efficiency. Moreover, cathode quality is also affected. A pyramidal structure is favoured in the presence of Fe+3 but the presence of LIX64N along with Fe+3 promotes a ridge structure. Addition of thiourea not only causes modification of cathode deposits, but also a rise in current Efficiency.

Jan 1, 1992

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

By Wooller R

The 3-D regular block model used for long term mine planning at Hamersley Iron did not fulfil the requirements for short term mine planning in terms of accurate representation of geological structures, contacts and boundaries in the orebodies. A computer model, based on zone plans, is being created as a single orebody model for all phases of mine planning. The zone plan is the primary interface between the geologists and mining engineers. It is essentially a bench plan at mid-bench height showing geological structure, material type boundaries, the grade and physical characteristics of ore blocks. The method allows for the dilution of ore zones by waste material. The stratiform nature of the orebodies allows zones of varying grade to be readily delineated on the plans. The Zone Plan Model (ZPM) is the interface between geological and mine planning computer systems. It is the basis of all mine planning with applications including long and short term mine plans, reconciliations, general ore reserve estimations, pit design and general model enquiries. The system was designed to be user driven. The user has complete control at all times as all computer generated data are fed back to the user who may then elect to override the computer. Various controls were built into the system to ensure model validity and integrity. The system has proved to be invaluable as a tool for users with little or no computing experience.

Jan 1, 1986

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993

The combustion characteristics of Australian coals which contain high inertinite have been studied in a laboratory drop tube furnace and a Thermogravimetric Analyser. The pyrolysis chars and combustion residues were microscopically characterised using a modified coal petrography technique. Results indicated that the overall burnout of inertinite-rich Australian coals under pulverised fuel combustion conditions could be generally within a range of 97 - 99 per cent burnout. The studies showed that poor coal burnout cannot be generally related to high inertinite content in the Australian coals. The extent of coal burnout varies from coal to coal and vitrinite as well as inertinite may contribute to the unbumt chars in combustion residues. Combustion conditions had greater influence over char formation and coal burnout than the coal properties. However, under similar pf combustion conditions, coal rank and coal maceral composition had a strong influence over the coal combustion behaviours and final coal burnout. Simple correlations using coal properties may be used but with caution to determine coal volatile release and burnout at high temperature and rapid heating conditions.

Jan 1, 1991

By R C. Schodde

The future of any mining company depends on maintaining and growing its access to high-quality mineral resources. Often the true size of a given resource is not fully recognised until after mining has commenced. Also, the strong desire to increase production puts pressure to expand the resource base of the mine to get maximum value out of the capital employed. This, plus diminishing M&A opportunities and declining world-class greenfield discovery rates, makes brownfields exploration a high priority activity in any operating company. For the success and long-term survival of the company it is critical that this is done well. The primary aim of brownfields exploration is to find or acquire new deposits within economic transport distance of an existing mine that will add materially to shareholder value through: mine or capacity expansion, displacement of lower-margin ore from the mine plan, preserving and extending the mine life, and ensuring potential value is understood in order to maximise potential future mine development or exit. A number of strategic principles are important in any program designed to achieve these aims: understanding the life of mine (LOM) production profile and the related key drivers for exploration, understanding the dynamic nature of the brownfields search space, understanding and measuring depletion of the brownfields search space, understanding the potential of the near-mine region, investing in exploration technology to expand the search space, and investing in a basic geological understanding of the ore-environment. Examination of the LOM profile will highlight critical issues facing development plans for the mine including future grade and throughput issues, key technology requirements or innovations and scenarios for increased production. Exploration targets in the brownfields program should address these key issues. Often it is as æsimpleÆ as keeping mine development sufficiently far ahead of extraction to allow time for the various phases of exploration and resource assessment drilling. Because of the low additional capital costs required, expansion of the brownfields search space is strongly leveraged to: metal prices, development of new markets, incremental operating cost reductions, strategic changes in downstream requirements in integrated businesses, depletion of higher unit-value ores, and new technologies (both extraction and exploration). Therefore the brownfields search space is likely to incrementally expand through time and must be regularly reviewed. This is also important as any given search space will be progressively exhausted, resulting in smaller and higher cost discoveries. It is therefore important to monitor and critically review sustained trends of increasing brownfields discovery cost. The first wave of discoveries in any camp are usually empirically driven and do not need a strong geological understanding. However, an improved geological understanding is critical to making the next generation of hidden discoveries. To illustrate these points, a case study was carried out on the exploration and development history of the Kambalda nickel camp. Over a period of 40 years, more than 40 deposits were found containing over 1.7 million tonnes of nickel metal. Efficient mines need to maintain reserves for operating flexibility. Consequently, the company needs to clearly understand the global resource in order to maximise its full potential. In addition, understanding the full brownfields potential earlier in the development of a deposit rather than later, creates optionality through the flexibility that this understanding brings to future development choices. To ensure best practice in attaining this aim, the roles and responsibilities of the exploration team and the mine operation should be clearly understood. It is important for the explorers and the operators to have shared views about what needs to be done. Typically, mine operators would be accountable for identifying future resource requirements to support the life-of-mine production schedule whilst explorers would be accountable to ensure best-practice assessment of brownfields exploration opportunities. This would include an assessment of the global undiscovered endowment in the regional near-mine area. The balance between brownfield exploration drilling and resources to reserve conversion will need to be decided to ensure efficient operations are maintained. Both need to agree the optimum level of brownfields funding taking into account: urgency to replace or grow reserves, and quality of opportunities (relative to those elsewhere). The ultimate cost of ignoring the full brownfields potential of an operating asset can be significant, ranging from inefficient and poorly planned operations, lost opportunity cost and resultant value through under-utilised resources and, in the worst case, early exit from the asset at the bottom of the commodity cycle û leaving behind huge amounts of shareholder value.

Jan 1, 2006

Ulan Coal Mines Limited operates an underground and open cut mine near Mudgee in the Central West of NSW. The mines are part of a Joint Venture managed by Exxon Coal and Minerals Australia Limited (ECMAL). Currently all the mines output of over five million tonnes per annum is sold into the export market predominantly as a steaming product.

Jan 1, 1993

By Shklyar FP, Babushkin NM, Bokovikov BA, Fedotov PB

A mathematical model for gas flow dynamics and heat and mass transfer processes occuring in the tuyere raceways and in the zone of the final for- mation and heating of pig iron and slag has been developed and simulated on a digital computer. It takes into account the formation and size of the raceway zones, combustion of coke and its substit- utes, oxidation of the metal, radiation from the gases to the raceway boundaries, physical heat losses and the direct reduction of the pig iron elements below the raceway zones. To evaluate the distribution of heat produced by the oxidation of metal between gases and prod- ucts of smelting, the problem of heating the mat- erials in the raceways with the sources of heat in the materials under conditions of intensive gas circulation in the raceways is solved. To determine the amount of heat transferred by radiation from the gas to the boundaries of the raceways, the problem of radiant heat transfer be- tween two grey bodies forming a closed system is solved. Using the structural parameters of the furn- ace, the inlet parameters of the combination blast and exit parameters of the melt, the model permits the calculation of the temperatures of materials entering and leaving the raceways and also the res- idual temperature of the gases, which qualitatively differs from the theoretical combustion temperature. Analysis of the operation of several different blast furnaces has shown that the overall picture of the interaction between gas flow dynamics, mass and heat transfer processes occuring in the race- ways and in the zone of final product formation, obtained with the aid of the model, now permits us to approach from a different position the deter- mination of the limiting factors in furnace operat- ion. It also allows us to explain certain phenom- ena observed in blast furnace practice and to dis- cover new relationships which may be used in analy- sis and control of the smelting process.

Jan 1, 1981

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

The narrow quartz vein deposits at Konongo and Ghana Main Reef gold mines in Ghana were emplaced during the plastic flow cross folding of pre-existing sub-isoclinally folded volcanic and perivolcanic deposits of Proterozoic age. The older fold structures tightened differentially according to their position in relation to the axes of the cross fold pattern giving complex outlines to the reefs in both plan and cross section.Some 4500 measurements of bedding plane linears were used in the resolution of the Boabedroo footwall structure at Konongo. The methodology developed at the Boabedroo mine was then successfully applied to other complex bodies at the Konongo and Ghana Main Reef mines.All mine development, especially stope preparation, of the folded quartz reefs at Konongo and Ghana Main Reef was controlled by the geologist to ensure that the veins were removed with as few geologically enduced hiccoughs as possible.

Jan 1, 1993

Tectonic subsidence plots have been calculated for well, extrapolated-well and significant off-well (seismically-based) locations in the Vulcan Sub-basin and adjacent highs (western Timor Sea). The subsidence curves have been normalized to a common datum, the distinctive "near top Permian" marker, and corrected for sediment compaction, palaeobathymetry, eustatic sea-level change and loading effects.Four principal phases of post-Permian basin development are recognised and quantitatively described by integrating the results of the sub-sidence analysis into the regional (e.g. recent Ocean Drilling Program-derived) framework of the tectonic evolution of the North West Shelf. They are1. the Triassic-mid Jurassic Westralian Superbasin intracratonic phase,2. the late Jurassic-early Cretaceous North West Shelf rift phase,3. the mid Cretaceous-Palaeogene North West Shelf subsidence phase, and4. the Neogene-present Timor collision phase. Rapid Triassic tectonic subsidence occurred in an intracratonic setting, possibly subsequent to aborted late Palaeozoic rifting. Intracratonic sub-sidence mechanisms such as deep crustal metamorphism and/or intrustion and regional tectonic compression are invoked in addition to any post-rift thermal subsidence which may have occurred.

Jan 1, 1990

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

By Vernon PN

The Eossing Uranium Mine is a high tonnage low grade open pit operation using acid leaching for uranium extraction and ion exchange and solvent extraction for solution purification. Advanced technology, much of it computer based, has led to major economies that have contained operating unit costs over the last four years in the face of double figure inflation. An improved ore reserve block model and mine planning system have achieved a considerable reduction in the stripping ratio. Drilling and blasting costs have decreased some 25%, mainly by the introduction of heavy ANFO explosive. A centralised computer control centre for the metallurgical plant has increased labour productivity resulting in improved process control. The all-staff workforce is united with management in the objectives of creating a safe, healthy, working and living environment and a prosperous company, capable of contributing to the wellbeing of the nation and the shareholders. This situation has been brought into being by an equal opportunity policy coupled with a management system emphasising open two-way communication through all levels in the organisation. The success of this policy is highly apparent in the morale and productivity of the workforce.

Jan 1, 1986

By Wall J, Platell R, Knight P

The Argyle diamond mine is located in the East Kimberley area of Western Australia, some 100 km south of the town of Kununurra. The diamondiferous Argyle olivine-lamproite diatreme was discovered in August 1979. Production began in December 1985 at a planned throughput of 3 Mtpa to recover 25 million carats of diamonds. Presently, Argyle is the world's largest producer of natural diamonds and produced over 40 million carats in 1993 from seven million tonnes of lamproite ore treated. Two phases of evaluation have been carried out. The first in 1981-82 was designed to prove around 60 million tonnes of ore to justify the establishment of a mine with a minimum life of 20 years. The second phase, in 1989-90 involved drilling the orebody to greater depths to provide data on which to plan the final pit design. The final pit contained 120 million tonnes of ore at 5.3 carats per tonne (ct/t) grade. Mining of the planned pit will extend the mine life to around the year 2004, following which it is possible that a further cut-back could be mined. There is also the potential for future underground mining. A substantial amount of geotechnical work has been undertaken due to the fact that the pit will be nearly 500 m deep and is located in a mobile zone causing abnormally high residual stresses to occur in the pit walls. The occurrence of low strength rocks at depth in the pit walls further complicated the situation. Hydrogeological investigations were done to determine pit dewatering requirements and to assess the effect of dewatering on pit wall stability.

Jan 1, 1994

By P Benjamin, H Bohannan, C Farr

Geoffrey Blainey's historical account of the mining activity on the west coast of Tasmania, æThe Peaks of LyellÆ documents the changes over 130 years of activity in the region. Commissioned by the Mount Lyell Mining and Railway Company, emphasis is placed upon the development of the Mount Lyell Mine in Queenstown. Chapter 19 æWidening HorizonsÆ details the review the Mount Lyell Company undertook in 1904/05 to ensure the future of the operation, following the pessimistic outlook regarding diminishing reserves and poor grade ore. The analogies documented between the Mount Lyell Company at that time, and Gold Mines of Australia 90 years on are remarkable, with both companies demonstrating a commitment to the Mount Lyell area through active exploration, the proactive search for alternative technology and the recognition of the valuable human resource. As Blainey writes (Blainey, 1993), æwith its expanding chemical works, its huge Tasmanian mines, its railways and smelter, its coke works and its mine crusade, Mount Lyell was probably one of the nation's five great industrial companies in 1906 or 1907. This brief phase of industrial and mining expansion had its seed in the threat of extinction . . .Æ After a number of reprieves, the Mount Lyell mine did stop production in 1994, but that only provided an impetus for a review and rebirth.

Jan 1, 1998