Search Documents

By Whitworth N, Anderson P

New plant has been commissioned to treat off-gases from the Fluo-solids Reactor in the Copper Smelter. The new section of plant was built onto an operating system and commissioned with minimum disruption to production. Under construction is a 270 m tall stack for Lead Smelter gases. Additional items for the Lead Smelter will include a new gas cooler, a central baghouse to replace Sinter Plant wet gas scrubbers, a new exhaust fan on the main baghouse, and ducting of drossing gases to the main baghouse. Emphasis is given to discussing improvements the new plant has made to working conditions, the general environment and increased production capability. Total expenditure in the two smelters is in the order of $25 million.

Jan 1, 1978

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

Australis Mining N.L. operates a continuous mode carbon-in-pulp (CIP) gold plant, processing sand and slime tailings from previous gold mining operations in the Norseman area. Plant design is that of conventional countercurrent contact between pregnant pulp and activated carbon. Gold desorption is achieved by the Zadra process using near boiling tempera- tures and atmospheric pressure. Process water is drawn from nearby Lake Cowan (saline). The plant operates at, or above, design specification of 400 dry tonnes per day. This paper describes the plant design and operating processes utilised in optimising throughput and gold recovery. TNTDnPTTnmTnM Favourable world gold prices and substantial reserves of sand and slime tailings prompted Australis Mining N.L. to construct a gold extraction plant during 1981. The projected plant throughput was set so as to complete treatment of available tailings over a three year period. Metal- lurgical tests indicated that, with a regrind facility satisfactory gold recovery could be achieved using a countercurrent CIP process. Reflecting the entry of Australis Mining N.L. into its first large scale treatment operation, the plant design emphasised simplicity but effectiveness of Operation.

Jan 1, 1982

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

By Sorokin M. L, Komkov A. A

Flash smelting of nickel sulphide concentrate has been practiced at WMC's Kalgoorlie Nickel Smelter for 20 years. The mineralogy of the concentrate from the original mines was particularly suited to this process. However, taking a strategic view, potential new processing routes should be fully evaluated as possible replacements for the current technology. The Vanyukov process has been under development in Russia for the past 40 years and has been successfully applied on a large scale to the smelting of copper concentrates, at two locations - Norilsk and Balkhash. The potential for the application of the Vanyukov process to the smelting of nickel concentrates offers a number of processing advantages, including smaller reactor and decreased dependence on fuel oil. This paper reports on preliminary investigations into the application of the Vanyukov process to the smelting of nickel concentrates. At this stage the investigations are limited to semi-quantitative comparisons and modelling studies.

Jan 1, 1992

By Aitchison J, Clarke G

A reappraisal of the stratigraphy, new regional kinematic analysis and thermobarometric data allow a new interpretation of the metamorphic zoning and tectonic structure of the Upper Eocene high-pressure metamorphic core complex of northern New Caledonia allow a three steps evolution to be proposed : 1) subduction and understacking of previously thinned continental crust elements; 2) subduction blocking due to the crustal thickening; 3) crustal thinning and extensional detachment during the diapir-like uplift and unroofing of the eclogitic core. Steps 2 and 3 may be partly contemporaneous. Such a model accounts for the thermobarometric and radiochronologic data, and also for the weakness of substratum deformation during the emplacement of the ophiolitic nappe.

Jan 1, 1995

Drilling has disclosed a sequence of Cainozoic sediments immediately to the west of the Ediacara mineral field containing little or no dolomitic debris in the lower and middle sections, but with gravel beds of dolomite derived from local rocks in the upper part. It is suggested that the lower and middle sequence of Cainozoic strata was deposited over the area of the Ediacara Range, and that this range was uplifted, probably as a horst block, during Quaternary times and was first exposed to subaerial erosion during the upper Pleistocene epoch.Lower Cambrian dolomites with associated stratiform lead mineralization, which formed the target of drilling on the western downthrown block of the Ediacara Fault, were eroded before deposition of Cainozoic sediments.Intense leaching of basal Cambrian dolomites around the periphery of the Ediacara Basin took place during Mesozoic and Tertiary times. This leaching process has resulted in enrichment of copper and lead mineralization in a thick marginal zone of residual clayey material overlain by dolomitic collapse breccia. These zones of leaching and enrichment were preserved under Cainozoic sediments which have subsequently been eroded. The Ediacara Fault appears to have been a major conduit for mineralizing fluids and is the main lineament of the Torrens Hinge Zone. Contemporaneous movements on this fault have controlled rates of depositionand thickness of sediments across the fault during Adelaidean and Cainozoic times. Though latest movements of this fault have been west block down, the predominant movement has been east block down with associated thickening of sediments to the east in the Adelaide Geosync1ine.

Jan 1, 1972

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

Projections of metal requirements for Japan and the United States indicate growing competit- ion for Australia's mineral output and a critical need for continuing discovery of new reserves. These projections may be modified by economic, social and political controls - the most import- ant factor probably being a shortage and the high cost of risk and development capital. Changing ownership patterns toward joint ventures and increased state participation are anticipated. New developments in global tectonics and metallogeny delineate favourable zones for ex- ploration and permit establishment of priority search areas even in regions of poorly known geology. Declining ore grades and special character- istics to meet technological requirements may modify identification and evaluation criteria. A broad approach considering all environments of concentration within the geochemical cycle is re- quired within any metallogenic province. The exploration geologist must be able to integrate geological theory, mining technology and financial analysis to establish well defined exploration objectives, in terms of economic and geologic models, in concept-oriented programmes.

Jan 1, 1973

By Fitter JF

Drilling and blasting practices at Groote Eylandt are undergoing a period of rapid change. Practices over the last ten years are reviewed and some specific blasting problems currently being faced are described. A move from percussion to rotary drilling is outlined, together with the reasoning behind a proposed return to ANFO from watergel explosives. A brief outline of the various firing patterns used is given, together with a description of the drilling and blasting recording procedures currently in use. Current and planned developments in drilling and blasting at Groote Eylandt are also outlined, emphasizing the success of wide patterns, fired in line with long inter-row delays.

Jan 1, 1982

IT is generally accepted that for transport of coal underground from different collecting stations, the system of endless rope haulage with remote control is not only one of the safest and most economIcal, but is also one of the most'efficlent in dealing with output.When the coal measures lie in regular planes, the work of laying down such a haulage presents no difficulties. When, however, the dip of the measures is Irregular, or dislocated by faulting, the management is faced with the problem of constructing vertical curves of such a radius that the sag of the rope will correspond with the road bed, and thus obviate the danger of the rope rising and throwing the skips off the track.The direction of the main roads for haulage purposes being ascertained from the plan of the royalty to be worked, the faults or dislocations in the seam are determined for these roads with the greatest possible accuracy by means of bore holes from the surface.From the data thus obtained the haulage road can generally be so graded that the rope will keep on the floor during haulage operations, although the grades may in places be synclinal.The writer confesses that he knows of no accurate formula for calculating the sag of the rope under varying tensions and so determining the safe radius of the curve, and he had to depend upon past experiences under somewhat sImilar conditions.The accompanying sections illustrate a case where the writer has recently installed an endless rope underground approximately 5000 ft. in length, from the foot of a tunnel in which an endless rope delivers the output to the screening plant, and having to negotiate, first a 400-ft. downthrow fault, and later a 32 ft. upthrow.

Jan 1, 1927

King Island is situated at the western approach of Bass Strait and approximately mid way between Victoria and Tasmania. The scheelite orebodies lie within the south east of the island. Ore bearing horizons from 10 m to 40 m thick occur in south and east dipping stratiform deposits. The orebodies occur in skarn formed by contact metasomatic replacement of carbonate rocks by granite intrusives. The scheelite is deposited as fine disseminated grains in and along the margins of andradite garnets in the skarn. King Island Scheelite operates two under- ground mines from which 350 000 tonnes per year are obtained. The Dolphin mine produces almost two-thirds of the total. See Figure 1. The Dolphin orebody lies beneath the sea and an area of reclamation. The orebody is inter- sected by zones of major dislocation. A chequerboard post pillar cut and fill stoping system has been chosen to provide the necessary support to the hanging wall. Because the stability of the pillars is critical to the economic welfare of the mine, considerable attention is given to the reduction of overbreak.

Jan 1, 1977

The Racecourse Orebodies at Mount Isa consist of a series of parallel steeply dipping lead/zinc/silver orebodies with a strike length of up to 1000 metres. Production from these orebodies between 13 Level to 9 Level has been by a series of cut and fill stopes in two level stages, leaving a crown pillar at 11 level. Development of the 15 level to 13 level extraction stage has recently been completed. The layout consists of a series of parallel stopes over a strike length of 1200 metres. Access to the stopes is by two declines connecting the stopes with a series of crosscuts This paper describes the basic layout with development and production methods employed.

Jan 1, 1977

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By Brown K, Francis D

The Yallourn Open Cut Mine has recently commenced mining operations in the new East Field which will supply the 1450MW Yallourn W Power Station for the rest of its 30 year design life. The authors describe the design and implementation process followed during the rehabilitation of the areas disturbed by works associated with mining in the East Field. One area of the East Field, the old external overburden dump, has been of particular interest and is discussed in detail. A discussion on the fire protection considerations is included as these are critical and often misunderstood as being contrary to good rehabilitation design practice. Finally, the development of a master plan for the rehabilitation of the Yallourn Open Cut in general, incorporating the East Field work, is discussed.

Jan 1, 1992

The advancements achieved in rapid tunnelling in the 60's and 70's have been notable. It is unfortunate that shaft sinking has not enjoyed equivalent advances and there are many good reasons why this is so. Technical and commercial considerations have held back development and continue to do so despite the increasing urgency in the search for minerals and energy. By the careful selection of an appropri- ate project and the application of specialist engineering the Bdard took advantage of a unique opportunity to apply a mechanised shaft borer in field conditions.

Jan 1, 1981

The production of 100,000 tonnes per year of synthetic rutile from the processing of ilmenite, coal and copperas (iron sulphate) produces 200 cubic metres per hour of effluent water. A 2.0 hectare biological filter, comprising natural and man- made wetlands, has been built into the last stage of the effluent water treatment system. It is an area of shallow water (

Jan 1, 1988

The magnesite deposits near Young, N.S.W., occur in decomposed serpentine rock below a soil. and alluvial cover. They show considerable variation in both quality and depth which greatly hampers mining operations. Seismic refraction techniques afford methods of conducting detailed and reconnaissance surveys which yield a depth and velocity analysis of the serpentine/magnesite refractor. The measured seismic velocities may be used as an index of the presence and quality of the deposits. The Seismic Timer which was used in the test surveys is a simplified seismograph which makes use of seismic reciprocity by replacing the conventional seismic shotpoints with geophone stations and the conventional geophone stations with impact points of a sledge hammer. Thi,s enables the use of detailed seismic refraction techniques which yield the depth and velocity analysis of the refractor.INTRODUCTIONThe magnesite deposits near Young, N.S.W., were produced by a process of leaching and enrichment of magnesium in serpentine rock. The magnesite occurs in nodular form emplaced in decomposed rock at shallow depths below soil and alluvium. The depth ranges from close to the surface down to some tens of feet. The deposits are patchy and show considerable variation in both quality and depth, giving riseto considerable difficulties in mining operations.Due to the thorough leaching of the surface material, geochemical tests carried out so far have not proved satisfactory for locating the pockets of magnesite enrichment.It was decided to test the application of detailed shallow seismic refraction methods to the investigation of both the depth and quality of the deposits. The tests were carried out...

Jan 1, 1962

The recent trend of installing flotation cells with volumes as large as 200 m3 in concentrators is driven mainly by economic considerations such as lower capital, operating and maintenance costs. Despite the economic advantages, the metallurgical benefits from these large cells have not yet been fully realised by the industry. This is mainly due to the lack of understanding of cell operation, viz cell mixing and hydrodynamics, gas dispersion and froth transportation behaviour in large cells. There is still no rational basis for selecting optimum cell operating conditions and down-the-bank operating profiles. The relationship between cell operating conditions and metallurgy is not well established. This has resulted in poor utilisation of cell capacity in many operations. The present trend of installation of fewer cells in a bank requires each cell to be operated very efficiently. Optimisation of cell operation provides an opportunity for significant metallurgical improvements in a flotation circuit with minimal capital expenditure. Extensive work on optimising of cell performance has been carried out at various Teck Cominco operations in Canada, Peru and USA. Three different levels were involved in this work. The first level was aimed at identification of cell operating conditions for optimum mixing and hydrodynamics, gas dispersion, entrainment and froth flow behaviour in individual cells. The objective of the second level was to identify the optimum bank operating profile for cells down the bank in a circuit. The third level then focused on controlling these cell operating conditions and bank operating profiles for tighter control of concentrate grade and recovery for optimum bank metallurgy. This paper presents some of the major findings at all three levels and demonstrates the importance of each level in optimising the performance of flotation banks installed with large cells.

Jan 1, 2005

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995