Search Documents

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, W.A. plant is briefly described. The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1979

Boring of a 7.5Km long tunnel under the city of Stockholm commenced in January, 1987. The 3.5m diameter tunnel will pass under the buildings and as no ground settlement is allowed, the regulation for water leakage into the tunnel is very strict. Probe drilling will be carried out continuously ahead of the boring and when water is encountered the rock has to be grouted before passing with the TBM. The tunnelling system enables probe drilling to be carried out during boring with the TBM. This has earlier been a capacity reducing factor as the whole operation has been stopped during probe drilling. The project is using a new generation TBM especially developed for hard rock formations which require higher thrust per cutter to get a high penetration rate.

Jan 1, 1987

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By B Murphy, J van Zyl, G Domingo

In a narrow vein mining scenario, employing preconcentration technology underground not only results in reduced transport and handling costs but may allow alternative mining methods to be implemented, improving overall productivity. Using processing technology underground is not a new concept with underground crushing and screening operations being quite widely utilised. With advances in processing technology over recent years, there are now a number of robust processing methodologies in existence that are capable of performing separation of ore and waste at a relatively coarse size. Many of these technologies are readily adaptable to the underground environment and if employed could result in a number of cost and productivity benefits.Assessment of the oreÆs suitability for preconcentration technology is the first step in harnessing these potential savings. This paper discusses how coarse ore sorting and gravity separation could be employed underground in a narrow-vein scenario and details the test work that is required at the front-end of a project to see if this potential exists.CITATION:Murphy, B, van Zyl, J and Domingo, G, 2012. Underground preconcentration by ore sorting and coarse gravity separation, in Proceedings Narrow Vein Mining 2012 , pp 237-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

The process of resource estimation of large precious metal deposits is illustrated by reference to major deposits now being mined or developed by Placer.The estimation procedure commences with building an appropriate model of the mineralization and proceeds through steps of data validation and geostatistical studies. It is important that the geologists most familiar with a deposit be involved with all stages of the estimate, and also prepare a manual estimate used to validate the kriged resource.Resource estimates are major exercises taking many man-months of work. The most time consuming part of this is usually construction of an appropriate three dimensional geological model. The data base for the resource calculations must be complete and checked for accuracy. The most appropriate estimation method must be selected.

Jan 1, 1990

Deep hydrothermal fluids adjacent to the Alpine Fault move through the brittle-ductile transition to mix with convecting fluids from near surface environments. These tectonically driven fluids evolve mainly from prograde metamorphism at mid crustal depth (ten kilometres) within the ductile regime which has been elevated due to advection and drag on the fault plane. Through the onset of brittle failure and cataclasis within Alpine Fault mylonites, fluid overpressuring results in hydrofracturing and localized implosion. Along the length of the Alpine Fault, hydrothermal alteration varies on most levels (Table 1). There is an observable increase in Fe-Mg carbonate between the Waitaha and Taramakau Rivers (between Ross and Aurthur's Pass, respectively). Field studies concentrate to the north east of the Arahura River, noted for historical mineral wealth. Late meteoric fluids move through cataclasite, brecciated mylonite, and other open fractures. Chloritisation is the major retrogressive phase. Dolomitic hydrofracture veins (Figure 1) within coherent mylonites contain iron and copper sulphides. Notably, the enrichment in Fe-Mg carbonate towards the Alpine-Hope Fault intersection seems to represent a region of enhanced permeability possibly related to shallow seismicity, increased regional faulting, footwall variation, strike-slip dip-slip distribution, and/or topographical anomalies (ie saddles). Isotope studies identifying an 'Inboard Fault Gouge Calcite Zone' correlate to values from the Main Divide region at the headwaters of the Arahura River (Browning Pass-Wilberforce Valley) (Becker et aI, 2000). These correlations are supported by rare arsenic anomalies (avg l06 ppm n = 5, Figure 2) found in both regions which suggest that fluids may be interconnected at depth.

Jan 1, 2001

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000

By Wu H. W, Just G. D

Australia's mineral resources boom in the two decades up to 1980 saw the establishment of about 25 new mining towns across the continent Quality housing and a high standard of community services were incorporated to attract a labour force for the major mine or mines i eing serviced. Town construction costs were high and were principally born by the private enterprise mine developer. There has been a change in the pattern in recent years and over 20 new mine developers have adopted a fly-in fly-out arrangement rather than construct new towns. Employees are drawn from a home base which is typically a large city, coastal community or established mining town and flown to the mine site for intensive work periods of about two weeks. The change has occurred for many reasons. Mining companies have been unwilling to support the high construction costs of towns, short life and smallermining operations do not justify a town, fast jet aircraft are available and there is a better perceived family lifestyle in established (coastal) communities. On the other hand reduced permanent development at new mine sites does not assist Australia's perceived need for decentralization. There have been questions as to the social problems which may develop from the artificial separation of the "breadwinner" from his family. The paper reviews a recent survey of the attitude of Australian mining companies employees, governments and unions to fly-in fly-out arrange- ments. The support for this approach is analysed and conclusions drawn that the concept is likely to be with the Australian mining industry for some time in the future.

Jan 1, 1991

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

The Fosterville goldfield, situated 25 km east of Bendigo, Victoria was at its peak between 1894-1910 with some 47 600 ounces produced (Figure 1). Since that time intermittent mining and tailings retreatment was undertaken until Bendigo Gold Associates delineated a viable resource and commenced an open cut heap leaching operation in early 1991. Unfortunately they encountered financial difficulties and Perseverance Exploration purchased the mine in April 1992. Perseverance operated a successful heap leach operation nearby Nagambie, 100 km east of Fosterville. Based on its acquired heap leaching experience, Perseverance Exploration was able to instigate operational changes to create a successful small gold heap leach operation. The major change was the using of the original multi-use leach pad as a single-use leach pad. The available data allows for a comparison of the two operating systems.

Jan 1, 1994

By Isaac AK

The combination of shot-firing and stage loader, and a prop and bar support system is an accepted drivage method. The support configuration is based on the final prop density, and assumes relitively uniform load sharing between the props. During the development of a longwall faceline at a medium depth (approximately 600m) British coal mine using such a drivage method, a fall occured overnight, effectively closing approximately 40m of the drivage. The severity and speed of the fall prompted an investigation into the performance of the temporary support system installed prior to chock installation. This paper deals with the investigation which disclosed some major contributory factors towards loss of strata control.

Jan 1, 1986

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939

By C Rogers

"The Coal Seam Gas (CSG) industry has seen a rapid increase in activity over a 30-year periodfrom the early 1990s within Australia. Despite public concerns over environmental issues, theCSG industry has increased in Queensland to the point where more than 90 per cent of naturalgas consumed in Queensland is CSG. The New South Wales (NSW) CSG industry has been slowerto respond for many reasons. Ninety-five per cent of natural gas consumed in NSW comes frominterstate. However, CSG activity in New South Wales is increasing notwithstanding publicconcerns. The CSG potential of three Petroleum Exploration Licenses (PELs) are being assessedwithin the Southern Sydney Basin that provides a unique opportunity to develop resourcesstrategically around many abandoned coal mines. The question has been asked - what do theseabandoned coal mines mean to the project? Are they good or bad? Are they friend or foe? Thispaper att empts to answer these questions and in doing so describes the coal mine ventilation andgas management philosophies and practices used to assess gas production potential. The coalmining philosophies not only have the potential to assist in the construction of a highly successfulCSG project, but they also potentially add signifi cant pre production value by re defi ning how theresources and reserves are assessed and therefore valued. The behaviour of abandoned coal minesand the goaves within the PELs are not well understood by the petroleum industry. However, in the Illawarra region there is an abundance of coal mining knowledge and expertise that if properly focused can greatly increase the chances of project success."

Jun 1, 2012

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982