Search Documents

Drill and blast operations account for 12 - 15 per cent of total mining costs. This paper looks at a comparison between electronic detonators and non-electric detonators, focusing on the cost benefits associated with the high precision of the timing sequences of electronic detonators. An analysis of the total mining costs was made on two main case studies; one on a quarry in South Australia (Martin, 2007) and the other on a project undertaken at Sunrise Dam (Vaughan et al, 2007). The criteria used in the analysis included; the resulting fragmentation, a vibration analysis, crusher throughput and productivity analysis such as excavator cycle times, dig rates of the excavator and bucket fill factor. The results indicate that there were consistent production improvements and hence reductions in total mining costs attributed to the use of electric detonators. An increase in the degree of fragmentation gives lower crushing costs as more material passes through as undersize. This reduces truck delay time at the crusher, which in turn gives higher truck and shovels productivity as well as higher dig rates for the excavators.

Jan 1, 2008

The high cost of sampling systems is largely due to the fact that indiv- idual mechanical type sampling units must be installed at the discharge end of ore/pulp pipelines, that is, at points where the pipeline discharges into pump sumps or the like. A considerable economic advantage may be obtained in the use of a samp- ling device that can be installed at any point in the path of the trans- porting pipe line. Initial tests on a vertical line with an injection sampler using iron ore concentrates reveal the validity of this type sample versus that taken with a mechanical sampler. A descrip- tion of the injection sampler shows its simplicity of installation, requir- ing minimum downtime on existing lines.

Jan 1, 1976

By Teague JK, Read HW

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years. Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the Illawarra Measures of the Southern Coalfield of New South Wales were carried out. The optimum range of vitrinite was found to lie between 45% and 60% (mineral matter free). Above and below this vitrinite range coke strength deteriorated. I Coke strength indices increased with rank and the optimum vitrinite content increased with an increase in rank. These changes will require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal. . T Use of- petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved. Significantly more work is required before coal reserves can be utilised to optimum advantage. This work would require extension of-the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1970

By Campain RA, Horner NJ, Limerick JM

The review covers the different concepts of automation which are appropriate to non-ferrous smelting and the degree to which the smelter, and the furnace in particular, is amenable to total automation. Due to the problems peculiar to a smelter, it is unlikely that a fully closed loop system could ever be achieved and that the smelter will continue to depend upon extended manual control supported by computer based information sorting and optimisation.Generally, loop control is performed using Taylor's Mod III process control system. For distinct plant systems involving a combination of process loops, sequencing, and data acquisition, the company has developed its own microprocessor based systems. Process optimisation using computer based analysis of operating data is well established. Utilising this data, computer modelling provides manual set point supervision for the furnace process control system.The impact of automation on the workforce and on operating costs is also examined. Predictions on future developments in the field of automation, optimisation and sequencing are propounded and related to the non-ferrous industry at large.

Jan 1, 1985

The impact of moves to introduce Abori- ginal land rights was felt in the Northern Territory as early as 1972 when the Federal Government froze the processing of all appli- cations for mining interests over vacant Crown land. The Aboriginal Land Rights (Northern Territory) Act was finally proclaimed on Aust- ralia Day 1977 and since that date the mining industry and the Territory legislature have struggled to make the Act work. Despite these efforts long delays have been experienced by those required to negotiate mining and explor- ation agreements under the Act. In fact explor- ation on Aboriginal land has been effectively stiffled since the introduction of the Abori- ginal Land Rights Act. The Northern Territory government and the mining industry have both sought amendment to the Act to remedy some of its more onerous problems. These efforts have generally been fruitless. Some of the recommendations put forward by Mr Justice Toohey following his recent review of the Act would provide relief in some important areas. However, any such improvements are more than offset by a number of Mr Justice Toohey's recommendations which would severely disadvantage the vast majority of Territorians. A recent survey of mining companies seeking exploration licences over Aboriginal land indicates that many of the existing diffi- culties could be overcome without significant amendment to the Act but rather by the adoption of a positive administrative approach by the Land Councils. It is now up to the Commonwealth and the Land Councils to demonstrate that their Act can work without crippling the Northern Territory economy and its mining industry.

Jan 1, 1984

The mineral resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However, the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the resource, and add measurable value to the company. The concept of mineral resource management (MRM) has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of mineral resource management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of economic value added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2006

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

By Lawless JV

Recent exploration for gold on the Pacific Rim has utilised similarities between active hydrothermal systems and epithermal gold deposits. The major control over formation of such deposits is the hydrology of the ore-depositing hydrothermal system, which varies depending upon its geologic setting.

Jan 1, 1987

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By M Freeman

Significant improvements in the metallurgical performance at Pasminco Rosebery Mine have occurred over the last two years. Lead and silver recoveries have increased by more than ten per cent, lead concentrate grades are four per cent higher, zinc recoveries are up 1.5 per cent, and zinc concentrate grades have increased by two per cent. These impressive results have not occurred through the application of some new wonder reagent, but through the application of some fundamental metallurgical principals. The basic premise applied during this study was that to make an effective separation you must first achieve liberation. Therefore, the laboratory and plant studies examined the liberation characteristics within the lead circuit, and the impact of regrinding. The work demonstrated clearly that galena/sphalerite liberation was poor, and significantly impaired plant performance. Further, it was suggested that the application of lead regrinding of the lead scavenger concentrate and the lead first cleaner tailing would not only benefit lead metallurgy, but also improve sphalerite flotation. A similar approach was then applied to the zinc circuit. From these studies, solutions applying simple circuit changes utilising existing equipment were proposed and implemented. Further to the improvements in galena/sphalerite liberation, significant improvements in concentrate quality were achieved by reducing variation within the process. The implementation of changes in work practices negotiated in the Enterprise Agreement, employee contributions and specialist training also made a significant contribution to the unprecedented improvement in the lead and zinc flotation circuit performance. The results of these plant changes are discussed, along with the suggested scope for further improvement.

Jan 1, 2000

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

By Kennedy JT

This is a question that will be asked many times and by many individuals during the various evaluation stages of any new project. However, the question itself will often have different connotations to the different groups invariably involved in such an exercise. As examples, consider just three of the several different groups involved in the development of a new mining project - Financiers, Consulting Engineers and the Sponsors of the project (potential borrowers). To the Financiers, a 'bankable project' will be one against which they will be prepared to lend funds (but not necessarily all of the funds requested by the Sponsors). This usually means that in the first instance the technical information presented to the bank has satisfactorily covered all of the requisite areas to the levels of accuracy required. More importantly, the financial evaluation of the projected economic performance of the mine, as a whole, is considered sound and a set of arrangements under which the bank is prepared to advance loan funds have been structured which fully satisfy the bank's credit criteria. To Consulting Engineers preparing a feasibility study (or a part thereof), on behalf of the project Sponsors, the term 'bankable' invariably only refers to the technical completeness and the level of detail contained in the report which they are preparing. Their scope of work will not necessarily have been broad enough to fully satisfy a bank's requirements. It is unusual to see any specific references to overall project viability or profitability in Consulting Engineers' feasibility reports, other than those which are automatically associated with the use of the term 'ore'.

Jan 1, 1990

Urban railway systems need high invest- ments, especially if their routes and stations have to be placed in the subsurface. In the FRG the construction and equipment cost of urban underground railway systems are in the range of 60 to 100 Mill DM per km tunnel. For this reason, track sections on the surface and on elevated structures are used as far as that is possible. Considering whole systems, the costs are in a range from to 45 Mill DM per km length for a metro system with about 80 % of its tracks and stations in tunnels and from 20 to 25 Mill DM per km for a light railway system with about 25 % subsurface infra= structure. The amount of route lengths in tunnels depends on the size of a city, the situation regarding above ground structure and free space on the surface, the level of service quality which has to be achieved with the railway system etc. Despite of the urgent needs to improve the transport conditions there very often arise doubts if an urban railway system is really necessary and can be justified in an economic sense. The experience from many cities around the world shows, that there arise a lot of benefits from urban railway systems, especially with larger sections placed under- ground. They are to be found in the interests of the operator (f.e. operating costs), the user (travel time, quality of service etc.) and regarding social aspects (environmental protection, accidents, consumption of energy Etc.).

Jan 1, 1987

By Ya Vladimirov D, Yu Khudin M, Kiebanov A. F

Problems of the creation of an automated cartographic system for environmental condition estimation and forecasting in mining region are discussed in this paper. The Geographic Information System (GIS) ARC/INFO is offered as the platform for such a system. A breadboard model of the system was tested on the example of Kemerovo province (Kuznetsk coal basin), the most ecologically impacted mining region of Russia. As a result parameters of territorial distribution of integrated adverse environmental impact of the industrial enterprises are reviewed. Administrative regions of Kemerovo province were rated according to a degree of environmental pollution. Further, specific weight of various industries in pollution of region is determined.

Jan 1, 1995

In the traditional analysis of airblast and ground vibration, it is often assumed that only that single blasthole possessing the maximum charge weight (or a small group of blastholes initiating in an 8 ms time window) will determine the peak level of airblast or vibration. This assumption is examined in light of waveform superposition, and is found to be unsound. More rational alternatives are given in which all blastholes (or a selected number of blastholes) are assumed to contribute, in varying degrees, to the peak vibration or airblast. However, it is also shown that there is generally no precise solution for determining the number of blastholes that contribute to the peak level. The technique of waveform superposition does not rely on evaluating which group of holes produced the peak, and so is the preferred method for prediction. Some numerical and analytical models of wave superposition for airblast and vibration are also reviewed and recent approaches discussed. The directionality of airblast, in particular, is analysed in detail using a new superposition model that is constructed of two submodels, onenumerical, the other analytical. This model shows that the airblast from even a single blasthole can be highly directional. The detail of this model is commercially sensitive and will not be discussed. Only results and a broad discussion will be given.

Jan 1, 2004

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

Silica-Kaolin Sand Wet Sizing The Bulgarian deposits of silica-kaolin sand are localised in the eastern part of the Danube plain. After wet separation the raw material yields two products - washed kaolin (different grades) and silica sand (different grades). The water washing technology includes: disintegration; spiral classification; hydrocyclone classification and dewatering of kaolin grades; hydroclassification; sizing using drum screens and dewatering of silica sand grades. Research and development program has started to improve the silica-kaolin sand separation in processing plants. Based on the raw material and tails characterisation data and the preliminary experiments using Derrick Stacksizer screening machines a silica-kaolin sand wet sizing technology was developed. The full-scale pilot flowsheet includes the following units: Derrick Stacksizer equipped with 0.43 mm opening Derrick Urethane Panel; 500 mm Flat bottom Hydrocyclone; Derrick Stacksizer equipped with 0.150 mm opening Derrick Urethane Panel; 100 mm Hydrocyclone and Derrick Dual Motor Linear Motion Machine equipped with 0.064 mm opening Derrick Pyramid Panel. The pilot-test data clearly demonstrate that the new silica-kaolin sand wet sizing technology is suitable for Bulgarian silica-kaolin raw material. There are possibilities to increase the silica sand recovery increasing the production of silica sand grade PK 0.16 and starting the production a new grade PK 0.10.

Sep 13, 2010