Search Documents

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

Traditional techniques for extracting pillars in thick underground coal seams in India are reviewed. Problems encountered are principally control of roof strata and low recovery. Recently developed mechanized methods and projected newer techniques are discussed.

Jan 1, 1986

At the Highway gold deposit, 37 kilometres south of Charters Towers, gold mineralisation occurs in several stratiform layers and is enriched near the surface by lateritic weathering. The host rocks of the mineralisation are ferruginous and baritic, intensely sericitised, kaolinised and silicified rhyolitic tuffs and pyroclastics of the Cambrian-Ordovician Mount Windsor Volcanics. The geology of the deposit is illustrated in Figures 1 and 2.Forty-six reverse circulation percussion drill holes were completed by North-Queensland Resources N.L. for a total of 2,093 metres of drilling to further outline and test the open pit resource. The drilling indicated a resource of 171,000 tonnes averaging 4.4 grams per tonne gold and 5.0 grams per tonne silver.A shallow initial pit, approximately 30 metres deep, has been designed to mine the high grade upper portion of the western stratiform layer and part of the eastern layer. This initial pit is designed to mine 45,400 tonnes of western mineralisation at an average grade of 7.84 grams per tonne gold and 22,200 tonnes of eastern mineralisation at an average grade of 1.42 grams per tonne gold. Waste is estimated at 110,900 tonnes.

Jan 1, 1986

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By Gray N. B, Grimsey E. J

A steady state heat and mass balance simulation of the Western Mining Kalgoorlie Nickel Smelter (KNS) flowsheet was developed within the framework of the commercial software METSIM. The KNS simulation can achieve all plant setpoints through the adjustment of controlled process inputs, and provides a useful tool for the evaluation of the current flowsheet and potential flowsheet developments The simulation model and a number of applications are discussed in this paper.

Jan 1, 1991

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By Dunbavan M, Mallett C. W

The sequence of development and back analysis of the failure of a spoil pile in the 1B pit of the Moura Mine are given. The mode of failure was a two-wedge mechanism with a basal slip plane passing through a clay band about 2 m below the pit floor. Remedial actions for improving spoil pile stability are discussed.

Jan 1, 1981

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By C F. Nichol, L Smith, R D. Beckie

A better understanding of the hydrogeology within mine waste rock and cover systems is essential for the quantification, prediction and prevention of metals loading to the environment surrounding waste rock piles. The effect of surface condition on the internal flow mechanisms within an intermediate-scale constructed waste rock pile is being investigated at the Cluff Lake Mine, Saskatchewan. Changes in the water balance, the outflow distribution and water residence time have been observed in the waste rock pile following successive modifications of the surface condition. The three year old, run of mine, free-dumped surface was ripped to a depth of 30 cm to 40 cm, and levelled in October of 2001. In August 2002, a 10 cm to 15 cm cover of compacted waste rock was placed on the pile. Outflow, precipitation and run-off data collected during natural and artificial rainfall events have been used to quantify the maximum infiltration rate, and the spatial pattern of discharge and cumulative volume of water that infiltrated into the waste rock under each surface condition. Infiltration data together with the outflow data provide a basis to address the residence time of water within waste rock and the dominant flow mechanisms for different surface conditions. With a free dump surface spatially distinct wetting fronts are observed at the base of the pile that vary in flow rate by an order of magnitude (measured at a 2 m by 2 m scale) and in time by up to a week. Following ripping and levelling, similar cumulative outflows were observed, but the magnitude and arrival time of wetting fronts changed across the pile. A decrease in outflow volume, a decrease in infiltration volume, a two-fold increase in the response time of wetting fronts and a more spatially uniform distribution was observed following placement of the compacted surface layer. Based on preliminary data, the internal structure appears to be the dominant factor controlling outflow variability.

Jan 1, 2003

By A Cooper

The current financial climate has given rise to fears that falling mineral prices and tight credit will force mining companies to cut back on production and new project development in a bid to cut costs and conserve cash. However, a prolonged squeeze on global supply can have only one result: a massive and potentially explosive demand for metals in the not-too-distant future. A resurgent global economy will also generate dramatic new demand for oil and energy, with a return to higher oil prices likely. How then should the mining industry plan for the future? In-pit crushing and conveying (IPCC) could lead the way as a partial or complete substitute for trucks. In 13 of 15 studies undertaken by Sandvik and Snowden, comparing IPCC with truck-optimised pit designs, IPCC generated operating savings ranging from US$0.18 to US$0.82 per tonne moved, compared to trucks. Trucks have higher operating, maintenance and energy costs than conveyors. New emission standards on diesel engines may make them more emission friendly but less efficient in terms of energy usage. With far more efficient energy use and cheaper operating costs per tonne moved than trucks, conveying offers an attractive alternative for the bad times ahead and into the apparent energy depleted future. When evaluating alternatives, a reasonable first step would be to conduct a scoping level study which analyses the differences in capital and operating costs between a truck and shovel operation and an IPCC solution. The study can also determine what type of IPCC is best suited to the particular mining application. The results can then be used to decide whether a more detailed study is justifiable. IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations. Sandvik (as an OEM with a full suite of IPCC equipment) can undertake these studies in ten working days in conjunction with Snowden or any other independent mine planner who knows how to schedule for IPCC. Because most mining industry personnel have been æborn and bredÆ on trucks and shovels û this paper focuses on some of the practical considerations necessary to make IPCC systems work that the Sandvik Technical Services Group has encountered during these studies.

Jan 1, 2009

The uptake of nickel into the lattice of pyrrhotite,Fel_oS has been studied experimentally in the temperaturerange 200 DC to 760 DC. Nickel from both aqueous solutionsand salt melts diffuses rapidly into the sulphide latticewith ,an accompanying rel~ase of iron into the solution ormelt. The rate of uptake of nickel and its diffusion intothe sulphide lattice have been followed ,by opticalmicroscopy and by analysis with an electron probe microanalyser.Some geological consequences of this phenomenonaffecting the distribution of nickel in rocks associatedwith nickel-iron sulphide ores are discussed.

Jan 1, 1980

By Saghafi A

Spoil piles are produced routinely in open cut coal mines. Spoil piles may contain waste coal and other carbonaceous horizons. Coal and carbonaceous materials react with oxygen in the atmosphere, producing heat. If the rate at which heat is generated is greater than the rate at which heat can be dissipated, the temperature of the spoil pile rises. If the heating remains unchecked, spontaneous combustion can occur. Spontaneous combustion poses significant safety, environmental and economic problems if it should become established in spoil piles. Using the basic features of self heating in spoil, the use of model is directed toward developing quantitative prediction of spontaneous combustion in open cut coal mine spoil Piles.

Jan 1, 1998

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By Large RR

Precious metals in the Rosebery north-end orebody occur predominantly in sphalerite- galena-pyrite ore and to a lesser extent in massive barite mineralisation. Gold may also occur in the upper parts of pyrite-chalcopyrite ore (although this ore type is usually gold poor), in pyritic mineralisation lateral to base metal sulphide lenses and in the footwall (very patchy). Although present, remobilised precious metals do not occur in economically significant quantities. Mineralogically, silver occurs dominantly in tetrahedrite and, to a lesser extent, argen- tiferous galena. Gold occurs as electrum associated dominantly with pyrite and, to a lesser extent, tetrahedrite. Geochemical modelling suggests that silver was probably transported as a chlorocomplex, while gold was transported dominantly as a thiocomplex, although at high temperature gold was transported as a chlorocomplex.

Jan 1, 1987

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005

Underground mine ventilation is now com monly simulated on a digital computer. Such a programme, incorporating natural ventilation has been modified by others to account for methane emission and elevated local tempera- tures. At Wollongong University, the pro- gramme was further developed and extensive interactive graphics incorporated such that any view of the three dimensional mine could be viewed, and superimposed upon that view are areas where a nominated parameter has exceeded a particular value - generally at a nominated time after a particular event and usually a fire/explosion of one type or another. A further programme was developed such that up to 20 'times' could be examined at a particu- lar location after say, a fuel rich fire at some other place in the mine. The output from this programme includes a plot of methane 1, smoke 1, temperature, pressure and air flow versus time - a most useful graphic to observe the limits of safe attendance in a particular Airway.

Jan 1, 1983