Search Documents

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By Ma F, Yang Q, Ujihira M

The effect of stresses and acoustic emissions on the gas permeability of coal was investigated in the field and the laboratory in order to find an estimative method of the practicability of gas drainage. In the field, acoustic emissions and gas emissions during gas drainage drilling were monitored tentatively at some coal mines in Japan and China.In the laboratory, acoustic emissions from coal specimens in addition to gas permeability were measured during the triaxial compression loading in order to interpret the results monitored in the field. Besides, the opening of gas permeation channels in coal was considered on the basis of the experimental results.

Jan 1, 1991

By E du Plessis, M Rowley, M Fallon, F Golenya, R Swanson, I Robertson

"Check sampling programs were undertaken at Barrick Australia Pacific LimitedÆs Lawlers and Plutonic mine sites in Western Australia. The programs identified that the sampling, sample preparation and assaying protocols required modification to ensure acceptable precision (reproducibility) for each gold mineralisation type. These case studies describe the processes used to identify the: inconsistent precision different types of test work programs that were conducted to quantify the appropriateness for each mineralisation type steps used to modify the protocols.The type of test work conducted included: a duplicate series heterogeneity test for particulate gold mineralisation in the Lawlers gold deposit screen fire assay test work on duplicate subsamples for arsenopyrite associated mineralisation at the Plutonic gold deposit.Each test work program required a detailed scope specifying the sample selection criteria, sample preparation and assaying steps. The aim of the test work flow chart design was to ensure the assay precision between the different particle sizes or duplicate sample pairs could be measured and calculated. In the screen fire test work the true grade of the primary sample was calculated and compared against each subsample.A high quality assay laboratory was utilised for the test work. All samples were fire assayed and the gold grade determined using a gravimetric finish. The assay results were validated and the data was analysed using tables and graphs in spreadsheets. Following data analysis a modified sample preparation and assaying protocol for each mineralisation type was designed for use by the principal assay laboratories. Following implementation of the new protocols, routine check samples were collected during the sample preparation and assaying stages to monitor the performance of the new protocol.CITATION:Fallon, M, Rowley, M, Du Plessis, E, Golenya, F, Robertson, I and Swanson, R, 2012. Confirming the sampling, sample preparation and assaying protocols used at two Yilgarn gold deposits, in Proceedings Sampling 2012, pp 47-62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

In the southern part of China, car-bonate rocks outcrop in large areas. Ka-rst develops owing to hot, humid climate and heavy rainfall. In deposits of coal, iron, bauxite, tungsten, tin and base metals exist karst formations within or near the mineralization zones. Three pro-blems should be solved in the mine cons-truction in karst region. The first is the drainage and safety control of karst groundwater. Different methods are used to cope with local hydrogeological con-ditions, e.g. drainage from surface by submersible pumps in wells penetrating groundwater seams; drainage from under-ground drifts which intercept groundwa-ter flow with clusters of holes drilled into karst aquifer or with vertical ho-les drilled from surface to the drift underground; cement grouting to block off channels or to seal a part of aqui-fer; groundwater pollution control; etc. With those measures many Chinese mines of tremendous waterflow were success-fully developed and valuable experiences were gained. The second problem is the stability of buildings deteriorated by surface subsidence due to drainage. The occurence and distribution of surface cavings by drainage were studied.

Jan 1, 1990

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

By La Brooy S R, Fenton K

A low grade copper flotation tailing from Telfer containing 1.2% Cu as chalcocite and cuprite and 5 gt-t Au was leached with ammonia, cyanide and ammonia-cyanide mixtures to extract copper and/or gold. Direct cyanidation extracted both copper and gold but consumed about 30 kgt 1 NaCN. Pre-leaching the tailing with an aerated ammonia solution containing 28 kgt 1NH3 and 17 kgtl(NHa)2S0a at pH 10 readily extracted up to 95% Cu in about 6 hours under optimum conditions. However pH and total ammonia concentration were critical factors. Subsequent cyanidation ex- tracted 80% Au using 6 kgt NNaCN. Ammonia-cyanide mixtures werefound to selectively leach gold over copper depending on the concentration and relative proportion of NH3 and CN. The best composition for leaching up to 80% Au from Teller tailing was 1.6 kgt t NaCN and 1.1 kgf 1 NH3 in the presence of 0.3 kgt t Cue+. Such a mixture left only 50 mgL-1Cu in the final solution after precipitation of some of the initially dissolved copper.

Jan 1, 1991

By M Lund

Due to operational and regulatory practicalities, pit lakes will continue to be legacies of many open cut mining lease relinquishments. Unplanned or inappropriate management of these significant geographical features may lead to a short-term liability to all stakeholders during mining operations, or to ongoing liability to the local community and environment following lease relinquishment. However, the potential for pit lakes to provide benefit to companies, communities and the environment is frequently unrecognised and yet may be a vital contribution to the sustainability of the open cut mining industry. Improved remediation technologies are offering more avenues for pit lake end use than ever before, at the same time mining companies, local communities and regulatory authorities are also becoming more aware of the benefit these water resources have to offer. Sustainable pit lake management aims to better minimise short- and long-term pit lake liabilities, and yet also to maximise short- and long-term pit lake opportunities as well.

Jan 1, 2006

Ore sorting is a high capacity, low cost method of preconcentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal sub systems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry.

Jan 1, 1980

By R Hindstr÷m

The demand for iron ore has increased dramatically in the last years and is forecast to remain on a stable high production level for years to come. ItÆs expected that the world economy is facing a stable continuous growth of iron ore to two billion tonnes and more over the next decades (Beddows, 2007). Furthermore it is expected that the existing and known high-grade ore resources will decline, and the iron ore industry will be forced to implement more and more advanced beneficiation plants. As a consequence of the more complex beneficiation requirements, there will be a need for modern solutions for iron ore dewatering that are reliable mechanically as well as cost effective and with high capacity per unit at the same time. Conventional vacuum filtration methods have been the most prevalent in fine iron ore dewatering. Product quality needs, lower ore grades, complex mineralogy and energy costs have resulted in iron ore producers seeking better solutions for dewatering, in particular pelletising feed. New advanced filtration methods have been introduced to the market. This paper describes how these modern methods are answering the needs of the industry. Performance of advanced dewatering technologies (pressure filtration and ceramic capillary action filtration) for iron ore applications has been studied, and the findings are based on both industrial and pilot scale experiences on different materials. For example, the results show that the cake moisture content of iron ore pelletising feed can be optimised more effectively by using modern filtration technologies. By selecting the most suitable and adjustable equipment, the effects of variations of feed material on downstream processes can be minimised and the possibilities of processing more difficult raw materials to high-quality pellets are better. The Larox Corporation develops, designs and manufactures industrial filters and is a leading technology company in its field. Larox is a full service solution provider in filtration for separating solids from liquids. As such, this paper compares the new developments in this market area with the prevailing known vacuum filtration technology, but focuses on a comparison between capillary action filters and rotary vacuum disc filters (RVDF). The trade name CeramecG is used to differentiate the Larox filter from the generic term.

Jan 1, 2007

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

This paper addresses the role of mine geology in mining geotechnics. The role is assessed and discussed in terms of five main elements; geotechnical complexity, geological complexity, mine scale, percentage sampling and geological uncertainty. Lastly, the overall objectives and mine geology requirements are listed in terms of the various mine development stages; exploration, feasibility-design and operating.

Jan 1, 1993

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

The Mammoth Copper Deposit consists of three distinct orebodies adjacent to the Mammoth Fault. This fault is arcuate, changing from a normal tension fault to a shear strike fault just to the north of the mine. Movement on the fault was probably contemporaneous with deposit- ion of the adjacent sediments. In the upper levels the No. 1 orebody occurs within a brecciated zone in the footwall of the fault, but at depth the No. 2 and 3 orebodies are stratabound by two brecciated lithologic horiz- ons. The host rocks are impure sandstones, arkoces and quartzites, which in the mine area are near the top of the Lower Proterozoic Myally Beds. Overlying these beds is a conglom- erate siltstone sequence which has been assumed to be the base of the Gunpowder Creek Formation. North and south of the mine the conglomerate rests on an erosional unconformity representing a major time break, but in the mine the uncon- formity and conditions of deposition of the conglomerate are obscure. Some mineralization is contained within the conglomerates. The sulphides present are chalcocite, bornite, chalcopyrite and pyrite. Chalcocite is dominant in the upper levels but could be en- riched by supergene processes. At depth, bornite becomes the dominant copper sulphide with lesser amounts of chalcopyrite, pyrite and primary chalcocite. Throughout the orebody minor digenite and covellite occur and arsenic is a minor constituent bound up with the pyrite. The bulk of the sulphides occur in stringers, fractures and breccia interstices but finer grained primary bedded sulphides can be observed. The genesis is probably a complex process in- volving active tectonic movements extending from deposition to post lithification giving numerous phases of brecciation and redistribut- Ion.

Jan 1, 1974

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976