Search Documents

At Bulong, the mineralised (>0.8 per cent nickel) ore exists within numerous lithologies, which can and do occur coincidently. It is very important to discriminate between the different host units for estimation purposes, stockpiling and scheduling. This allocation of host unit has relied upon visual interpretation by the geologist recording the information, which can be very subjective by its nature. By using quantified constraints, such as assayed magnesium oxide and iron, the subjectivity of describing the host material of nickel laterite ore is reduced. The constraints permit consistent identification of the various host units, which improves the confidence in the overall estimation and scheduling of the ore.

Jan 1, 2000

By P Radulovic, V Lawson, M Muller, J Wallace

The Mount Isa Copper Concentrator was commissioned in 1973. Since commissioning some significant upgrades have been undertaken such as: • the replacement of the rod mill/ball mill circuit with AG mills and the subsequent conversion of the AG mills to SAG Mills. • the introduction of columns as retreat cleaners in 1987, then reallocated as prefloat cleaners in 1994 and rougher cleaners in 1996.• the repurposing of some rougher capacity to preflotation roughing to remove carbonaceous pyrite and talc in 1994.• the introduction of a Jameson Cell for preflotation cleaning in 2000. • the expansion of the rougher and cleaner circuits in 2002 with the inclusion of 6 x 100 m3 Wemco cells to replace the capacity lost to preflotation and to increase residence time and improve recovery. In 2013 work commenced to replace the cleaner circuit after 40 years of operation. The new cleaner circuit, consisting of 3 x B5400/18 Jameson Cells, replaced the rougher cleaner columns, cleaners, recleaners and retreat Agitair banks and was commissioned in Sep 2015. The new cleaner circuit was configured as two cells in series producing the final concentrate and a cleaner scavenger cell to supplement the existing Wemco cleaner scavenger cells. The performance of the new circuit is discussed.CITATION:Lawson, V, Muller, M, Radulovic, P and Wallace, J, 2017. Mt Isa copper concentrator cleaner circuit redesign, in Proceedings MetPlant 2017, pp 279–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

By A Parry, C Fitzmaurice

After conducting laboratory ore sorting testwork on samples of a low grade nickel ore stockpile at Western Areas’ Flying Fox nickel mine, a mobile crushing, screening and ore sorting plant was located adjacent to the stockpile. An initial two month trial of the ore sorter program proved successful and was extended to process the entire Flying Fox low grade stockpile in a further four month campaign. A total of 167 660 t of low grade ore was processed, providing highly upgraded feed trucked 26 km to the Cosmic Boy concentrator. A more than three-fold grade increase was achieved on ore sorter accepts. The moderately upgraded fines that by-passed the mobile ore sorter were also subsequently blended into plant feed. This paper describes the mineralogy of the Flying Fox low grade ore, the mobile ore sorting campaign and provides some commentary on the economic and environmental benefits achieved in the ore sorting campaign. The ore sorting campaign demonstrated the benefits of being able to utilise mobile ore sorting equipment temporarily located adjacent to sub-economic low grade stockpiles in order to effectively treat these stockpiles and produce viable plant feed.CITATION:Parry, A and Fitzmaurice, C, 2018. The upgrading of low-grade nickel ore stockpiles at Western Areas Ltd Forrestania operations, using a mobile ore sorting plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 541–550 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Willems, J B. Crow, R Dale

Open pit mining commenced at Lihir Island in 1997 and is undertaken using a conventional drill, blast, load, haul methodology. Unique challenges at the operation include an active geothermal system, a well-developed advanced argillic blanket in the upper portions of the orebody and high rainfall. Grade control is effective utilising routine blast cone sampling. While this provides ‘just in time’ grade information for mill blending, there are opportunities to improve scheduling of mill feed, based on material classification of clay types and sulfur grades. The nature of the clay can impact on the handling properties while the sulfur grade is an important guide for autoclave blending, required for refractory gold. Drilling below the pit floor introduces hazards from the identified geothermal field. A trial Reverse Circulation (RC) program was implemented with the aim of defining four benches below the active mining bench. A comprehensive risk analysis, including the geothermal environment, was undertaken to design a drill collaring procedure with pressure diversion equipment. Operator exposure was minimised through ‘nil on foot’ principles with the driller located in an onboard cab, utilising remote rod handling. Sampling personnel operate in an elevated platform with access to protective covering. Samples from blastholes and the RC holes are processed at two site laboratories. One provides conventional Au fire assays with additional Infrared Combustion (Leco style) S analysis. The second laboratory collects material classification details from portable XRF (pXRF), near infra-red spectrometry (ASD) and Hardness Indicator Testing (HIT). An existing workflow was updated by the site to deal with the additional samples and ensure production ‘turn around times’ were retained for short-term planning. This required some changes to drying temperatures, compositing and screen sizing for the material classification. All results from the two laboratories are loaded into a centralised acQuire database for estimation into a single block model that informs the 13 week medium term planning (MTP) schedule. This paper describes some of the logistical issues faced when drilling in a geothermal area. It also discusses the selection and commissioning Quality Assurance of the sampling equipment and drill rig. Integration of the resulting assay data with existing resource models is also explained.

Mar 22, 2022

The emerging coal seam gas (CSG) industry has the potential to provide a large-scale energy province for Queensland. Aquifer impacts and management of associated by-product water, both in terms of quantity and quality, are pivotal considerations for the development of a sustainable CSG industry.Legislative changes have been introduced to ensure that the CSG industry manages potential groundwater impacts and beneficial reuse of the by-product water to a level acceptable to both government and the community.The relevant new pieces of legislation covering petroleum and coal seam gas activities include the Petroleum and Gas (Production and Safety) Act 2004 (P&G Act), Petroleum and Other Legislation Amendment Act 2004 (POLA Act), the Petroleum and Gas (Production and Safety) Regulation 2004 and the Petroleum Regulation 2004. Other relevant legislation includes the Petroleum Act 1923 (Petroleum Act) and Part 7AA of the Mineral Resources Act 1989 (Coal Seam Gas Regime). The P&G Act introduces a full regime for managing water rights. This includes provisions for monitoring and reporting on the effects that the taking of underground water under petroleum tenure has on other bores in the area. The P&G Act also imposes a æmake good obligationÆ on petroleum tenure holders, which requires the restoration of bores affected by the taking of water or the payment of compensation. These provisions represent a significant departure from the Petroleum Act, which says very little about water rights and does not specify restrictions on the taking of water under petroleum tenure. This paper attempts to outline the requirements and obligations of the P&G Act for the CSG industry in terms of underground water rights, development impact assessments, aquifer trigger thresholds, monitoring and reporting requirements, as well as the make good obligations.

Jan 1, 2006

I congratulate The Australasian Institute of Mining and Metallurgy on its decision to hold its Annual Conference here in Western Australia. Western Australia, with its abundant mineral and energy resources, plays a key role in the Australian mining industry... and Western Australia will continue to figure prominently in this vital industry for many years to come. The success of our gold, iron ore, bauxite, mineral sands and other primary industries has enabled Western Australia to contribute significantly to Australia's export revenue and, therefore, to the nation's economic strength. The State's mineral wealth has also provided the impetus for a recent surge in mining related activity, including a dramatic increase in downstream processing of our raw materials. Billions of dollars worth of new project investment is either committed or awaiting final approval - and most of this new investment is a direct result of a healthy and vibrant mining industry. The North West Shelf Project - which has been providing natural gas for homes and industry in Western Australia since 1984 - has also played a key role in stimulating industrial development. The availability of abundant, competitively-priced gas from the North West Shelf has - along with the availability of other raw materials - made Western Australia a more attractive proposition for industrial investment. The company I represent, Woodside Offshore Petroleum, is operator of the North West Shelf Project on behalf of the Project's six Joint Venture Participants - Woodside Petroleum Ltd, BHP Petroleum (North West Shelf) Pty Ltd, BP Developments Australia Ltd, Chevron Asiatic Limited, Japan Australia LNG (MIMI) Pty Ltd and Shell Development (Australia) Proprietary Limited. The theme for this Annual Conference: "Excellence - the key to the continued success of the Australasian mining industry" is appropriate to the North West Shelf Project. The pursuit of excellence has been a hallmark of the Project. The Joint Venture Participants have been conscious of the need for stringent quality control at all stages of development. Procurement and purchasing policies, for instance, have demanded strict adherence by contractors and suppliers to the highest standards and specifications.

Jan 1, 1989

By J Rutter, S Dunham

Technological advances in sensor and material handling technology has enabled a step change in mine operations performance. Sensors capable of monitoring the grade of broken rock mass can be mounted on shovels, truck loading units or conveyors allowing highly precise ore/waste decisions to be made on small parcels of rock, increasing selectivity. This increased selectivity has the potential to remove sub-economic material from the product stream prior to incurring ore treatment costs. Bulk ore sorting is capable of intervening at <10t “pods” on Run Of Mine conveyors, or alternatively at per bucket loading (5-100t) or truck scale (30-350t) parcels of ore. This Grade Engineering technique being developed by CRCORE (Rutter, 2017) can improve mill feed grade, remove deleterious materials and ensure that the high capital intensity ore treatment facility is presented with the best ore feed strategy. While this technology can improve mine economics, estimating the performance of a bulk ore sorting system is challenging. Traditional resource estimation practices such as Ordinary Kriging and Inverse distance weighting (IDW) are based on weighted averages, a process that smooths the grade profile, reducing modelled variance and dispersion. Its purpose is to generate a globally unbiased result but is less suited to generating a model of adequate granularity to enable confidence in local grade heterogeneity. This is an essential component for bulk ore sorting success. Estimating ore sorting performance requires knowledge of the grade-tonnage curve at the scale of the sensor diversion unit (SDU). Evaluation based on an estimator that smooths the SDU distribution will not correctly predict ore/waste separation or economic performance. Alternatives to traditional linear geostatistics have been tested on a variety of mineralisation styles. Additionally, a number of heterogeneity metrics have been developed to assist with evaluation and assessment. The difference between estimation for grade (metal) and modelling for traditional mining block models, versus methods used for predicting heterogeneity and variability are explored.

Nov 10, 2020

By G A Brown

Environmental legislation is changing rapidly throughout Australia at the present time, and with that change comes additional responsibilities for the mining and petroleum industries. Among the many changes that are being made are increased penalties for both criminal and accidental environmental impairment. The defences for criminal offences are limited and for other offences the laws may impose strict liability - in effect the offender is guilty until proven innocent. Mines may be included under contaminated land legislation, creating additional liabilities for clean-up, rehabilitation and long-term management. It is not unknown in Australia for the value of a mortgaged property to be less than the amount of the environmental liability acquired by a mortgagor in possession due to contamination of the site. An essential part of the management program for resource projects is now the regular conduct of an environmental audit, the results of which assist in the management of the legal and financial liabilities facing company directors and managers. The audit can also assist with negotiations with government agencies, staff, unions, insurers, Aboriginal and other community groups. An environmental audit may also help to ensure that companies are claiming the maximum allowable deductions for environmental works under the tax laws, and provide evidence in support of such claims. Environmental legislation affecting resource industries Environmental legislation in Australia is changing rapidly and can impose massive constraints, substantial administrative costs, and considerable liability on directors, managers and the corporation. Pollution control legislation Every State and Territory of Australia has a range of pollution control legislation contained in either individual acts relating to air, water, noise and land, or embodied in a single environment protection act. Pollution control legislation provides a critical management baseline for resource industries throughout Australia, often requiring the full-time attention of an environmental manager or an environmental department. In general, it is an offence to discharge effluents into water, or emit gases into the atmosphere above prescribed limits, cause noise above a regulated level, or contaminate land without a licence. A licence determines how much of a substance can be discharged, the location, the receiving environment, the quality, and the time at which discharges can be made or noise can be caused. Planning legislation Planning legislation controls where a project is located, how it will be constructed and operated, how large it is allowed to be, and what will happen once the project is completed. Development consents or approvals will generally contain a range of conditions controlling the preparation of the site, the construction of the facility and the way it is operated throughout its expected life time. Resource projects may be regarded under legislation as scheduled or designated developments requiring special treatment during the decision-making process. Under planning legislation, it is usual for resource projects to be subject to an environmental impact assessment process. Resource legislation Resource legislation specifically covering mining and petroleum in Australia, also contains requirements regarding protection of the environment during exploration for and extraction of minerals and oil. A mining or petroleum production lease usually contains numerous conditions regarding protection of the environment and rehabilitation of the site during and after the life of the extractive process.

Jan 1, 1994

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of &apos;overburden modification&apos; due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and &apos;overburden modification&apos; has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

ZINC concentrate, produced at Zeehan by flotation from Read Rosebery ore, is also dried and roasted at the same place for the production of a calcine suitable for use in the electrolytic zinc process at Risdon, Tasmania.DRYINGThe concentrate, dewatered to 12% moisture by an American filter, is fed into a dryer, the type of construction of which is similar to that of a duplex Edwards furnace. The dryer is 45 ft. long and 14 ft. wide, and has two rows of nine rabbles each, the two pairs nearest the firebox being watercooled.The longitudinal distance between rabble-centres is 4 ft. The rabbles are rotated at a speed of 3 r.p.m. by a I5-h.p. motor. Zinc concentrate is introduced by a screw feeder, consisting of two parallel-blade conveyors, revolving in opposite directions at aspeed of 31 r.p.m.Draft is supplied by a Sirocco fan, 15 in. intake, operated at 1340 r.p.m. by a 10-h.p. motor. The dust carried by the exit gases is removed in a wooden scrubbing tower, 3 ft. 6 in. x 4 ft. 6 in. x 27 ft. high, to which the fan delivers, and down which water issprayed.Wood (eucalyptus timber) is used as fuel, the consumption per ton of water evaporated being 0.55 :ton. Zinc concentrate from the dryer passed either to trucks for shipment or to Herreshoff furnaces. The portion for shipment is withdrawn at a point half-way down the furnace, being loaded on to a belt conveyor for transfer to railway trucks. The moisture at this point is 7% to 8%.

Jan 1, 1927

IN concentrating mills, where several millerals are recovered for realisation in more than one product, various systems are used to express the relative economic value of the work done, and, in the hope that it may prove of use to other operators, the writer will describe a system which, in his opinion, is more complete than any other that he has seen published.The controlling factor in all mill work must be based on the economic result represented by the greatest margin possible between the realizable value of the products and the cost of obtaining same.From a mill-man&apos;s point of view these are affected by the following factors:1. Metal contents of ore.2. Grade of products.3. Recoveries.4. Working costs.The grade of ore milled is usually outside the mill-man&apos;s control, but this may exercise a considerable influence on the grade of his products, metal recoveries, and revenue per ton of ore. Higher grades or recoveries may be obtained by using a more expensive process, or by additional grinding or reagents, and the economic comparison can only be arrived at by obtaining an analysis showing the monetary value of each variation within the possible limits.In the system to be described, the value of unit variations of metal contents of the ore, grade of products and recoveries are calculated in terms of a monetary unit per ton of ore with the returning charges ruling, and any suitable metal prices. To do this it is necessary to assume what, for convenience, is termed a &quot;standard&quot; set of results from the mill, preferably representing about average conditions, and having calculated the effect of unit...

Jan 1, 1931

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By B Dold

Western Europe is a dynamic region, with an emerging co-operation between the individual nations both politically, economically, technically and scientifically. The European Union, today with 15 member States and with a range of central European States applying for membership, is a catalyst for this Cupertino, using a combination of EU funds, for financing research initiatives, and legislation to enhance development of technology and environmental performance. Europe is a major net importer of metals but with a large potential for own production, in particular in the accession countries. The metals and mining sector is furthermore identified as having a large potential to generate wealth both in todayÆs EU and in the future, widened Union. This paper provides a chart of examples on the many research initiatives presently underway in Europe, addressing environmental issues related to mining. The list of programmes and projects does not claim to be complete; it is rather an illustration on the wideness of the approach, describing various ways for transboundary Cupertino. The approach taken by many of the programmes goes beyond the strict ARD scientific area and therefore only a limited number of the many programmes can be identified as ARD research programmes. Also national programmes, without EU funding, are operating, eg in Sweden, Germany, and UK. The picture is continuously changing with new programmes being commissioned and old ones being completed.

Jan 1, 2003

By P J. Jacobs

FORACO is the third-largest global drilling services company, and recently celebrated its 50th anniversary. The company’s historical roots are in French-speaking West Africa, delivering hydrogeological drilling services to resource companies, villages and regional centres. Today, FORACO operates over 300 drill rigs in more than 20 countries.The Asia Pacific region of FORACO runs a fleet of 37 late model drilling rigs servicing the diamond drilling, reverse circulation, coal, coal seam gas and hydro drilling sectors.FORACO Australia has extensive experience delivering large diameter coring (LDC) samples to the resource community. In the past three years, the company has been involved in six 8? coring projects in a variety of geographies and geologies, including iron ore, coal and uranium. FORACO has developed proprietary equipment and techniques to deliver cost-effective LDC samples with outstanding core recovery.The FORACO LDC sampling system is hands free, with mechanised rod and corebarrel handing to minimise the risk of manual handling injuries. Sample volumes are six times PQ (the common industry standard for large core samples), with core recoveries consistently above 96 per cent in extremely difficult formations.Eight inch coring is a conventional coring system suited to hole depths up to 150 m. For deeper applications, FORACO has recently invested over $4 M in a 6? wireline coring system capable of achieving depths of 300 m.CITATION:Jacobs, P J, 2014. Large diameter core sampling, in Proceedings Sampling 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The Chamber of Minerals and Energy of Western Australia Inc (CME) is the peak resources sector representative body in Western Australia. The paper gives a summary of the role and objectives of the CME, including its history, structure and key program areas. Particular attention is given to the role of the CME in the Eastern Goldfields of Western Australia. The paper details the types of CME membership that are currently in existence. The paper argues that a strong and vibrant CME is vital to secure the resources sectorÆs growth and development in future years.

Jan 1, 2006

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80&#160;000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100&#160;m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By V Ser, I Smit, C Robertson

Anglo American has been researching the potential benefits of inter-particle comminution techniques for several years. Inter-particle comminution has additional benefits in terms of milling circuit performance such as energy consumption and stability. This paper focuses on the flotation benefits. Inter-particle comminution leads to selective breakage, mineralogical analysis has shown that this leads to improved liberation of the valuable minerals. In addition to selective breakage, the relatively short residence time experienced in typical inter-particle comminution machines allows more efficient classification which contributes to a æsharperÆ product size distribution. The effect of particle size in flotation has been well documented in literature. In general, it is has been shown that there is an optimal particle size range for flotation, and that both above and below this range, flotation recovery is adversely affected. Results show that the narrow size distribution which results from inter-particle comminution improves flotation recovery. Furthermore, the absence of excessive fine gangue material which typically results from conventional fine (-75 ¦m) milling of talcaceous ores, can lead to 100 per cent savings in depressant consumption when such ores are subjected to inter-particle comminution. To-date, this technology has been evaluated on more than ten ores. This paper will focus on one set of results which demonstrates a number of common differences that exist between material that has been milled conventionally and using inter-particle comminution technologies, with emphasis on what the impact of these differences is on flotation performance. A pilot scale (200 kg/h) vertical roller mill (VRM) was used to produce the material, and the results shown will describe conventional laboratory batch, locked cycle and pilot plant flotation testwork.

Jan 1, 2005

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998