Search Documents

Marble deposits of dolomitic variety are available in large quantities in India and for extracting these deposits diamond wire saw cutting machine is mainly used. Cutting performance of the diamond wire saw machine depends on rock parameters, machine parameters and operational parameters. Rock parameters related to physico-mechanical properties, such as, compressive strength, tensile strength, shear strength, modulus of elasticity and abrasion resistance of marble play role in determining cutting rate and beads wear rate. Thus, this study was undertaken to determine the relationship between different physico-mechanical properties and cutting performance. This work also aimed at enhancing the cutting performance of diamond wire saw in dolomitic marble deposit. Study was conducted in the field at three different zones having deposit of soft, medium hard and hard dolomitic marble. During the study, cutting rates and wearing of diamond beads were recorded in the field. Physico-mechanical properties were determined in the laboratory. The results obtained were subsequently evaluated by using statistical analysis. Study revealed that these properties of marble play a significant role in the performance of diamond wire saw machine. Predictive equations for the wearing of diamond beads and cutting rate were developed based on regression models. Results of this study will be of ample use for operators of wire saw to achieve maximum cutting performance and for manufacturers in designing the diamond beads.

Dec 6, 2010

On 15 August 1998 the first section of the PUTRA LRT system was opened to the public as a free service prior to official commencement of revenue service on 1 September 1998. It is a remarkable achievement to open a highly advanced medium capacity urban railway scheme in four years after the outline concept began. Even more remarkable is the implementation of the next stage which is the underground section planned to be operational in mid-1999. The decision to build the first underground railway in any major urban centre is a technical challenge. The PUTRA LRT System can be likened to Hong Kong when the initial MTR system began in the 1970s and Singapore MRT in the 1980s. Prior to the PUTRA railway very little bored tunnelling had been undertaken in Kuala Lumpur. A few shallow sewer tunnels had been built but the main experience of tunnelling in Malaysia had been for water, hydroelectric and road tunnels usually through granite formations. The ground conditions in Kuala Lumpur were known mainly from experience of piled foundations and occasional deep excavations. The suitability and likely difficulties to be experienced during bored tunnelling could only be theoretically predicted. In both Hong Kong and Singapore, government owned corporations were set up to implement the scheme, but in Kuala Lumpur the whole project has been undertaken by a private company PUTRA, a wholly owned subsidiary of Renong Berhad.

Jan 1, 1999

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By G Hall

BHP BillitonÆs (BHPB) Yandi ore deposit is a channel iron deposit (CID) in the Pilbara district of WA. The ore is predominantly a goethite-hematite pisolite and overlays a clay at the base of the deposit. Knowledge of the location of the contact prior to mining is critical to maximise ore extraction and minimise contamination from and mining of the underlying clays which contain high levels of alumina. The contact between the iron ore and the clay is highly irregular. Traditionally the contact has been delineated by closely spaced drilling û this can be expensive and since each drill hole only provides a point sample measurement, irregularities in the contact surface can be missed. In September 2001, three high resolution geophysical techniques were trialled to see if they could be used to improve the efficiency and accuracy of ore delineation. The three techniques were resistivity imaging, ground penetrating radar and electromagnetic conductivity imaging. The resistivity data showed a favourable correlation with the available ground truth data from drilling. Using this ground truth data as a calibration, an interpretation of the depth to the base of the channel iron deposit (CID) ore was constructed for the areas surveyed. A significant attribute of the method is that the position of the base of the ore is imaged continuously along the lines that are surveyed rather than at discrete points. No continuous well defined ground penetrating radar (GPR) reflections were observed from the base of the CID ore. There did appear to be some correlation between the range of echo times that reflections were observed and the drill data, however the precision to which the range of echo times could be estimated was of the order of several metres and therefore not adequate to replace current procedures. The electromagnetic data showed good correlations with the existence of shallow clays but did not discriminate between variations in CID ore depth. This technique is therefore not suitable for mapping the base of the CID ore but may still be useful as a rapid tool for mapping the position of clay bands.

Jan 1, 2002

By J Whittle

This paper describes what is involved in carrying out a comprehensive optimisation of a long-term operating schedule for a mining complex. It details the data that must be assembled and discusses the different approaches to optimisation and what limitations they put on the variables and constraints that can be handled.CITATION:Whittle, J, 2014. Not for the faint-hearted, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

This paper describes modern long-term mine scheduling and gives an example of its application. It then discusses the obstacles to the implementation of such schedules.

Sep 26, 2011

By M Malec, J Szczerbinski

Hazards in underground mines are concomitant with the mining of mineral deposits and have their source in a minerÆs work environment. The authors of the paper have undertaken a trial classification of these hazards into three groups, depending on the sphere of their occurrence:lithosphere, ie rock mass, atmosphere, ie air in mine workings, and technosphere, ie machines, equipment and facilities in mine workings. The lithosphere creates such hazards as bumps, rock outbursts, the atmosphere is a factor causing fires, methane explosions and climatic hazards, whereas accidents concomitant with an operation of machines and equipment occur in the technosphere. Assuming that the number of accidents in the mining industry, concomitant with hazards, reflects the degree of safety, it has been shown, that in Poland they are under control to a large extent.

Jan 1, 1999

The An Shan iron ore deposit is the biggest low-grade oxidised iron deposit in China. Over the past ten years, about 120 SLon verticalring-pulsating high gradient magnetic separators units have been installed in An Shan to process oxidised iron ore. This paper describes how several plants have upgraded their old technologies to new technologies with SLon magnetic separators as the key equipment for controlling tails grades, including using reverse flotation as the key technology for iron concentrate cleaning, These plants have been modernised with beneficial results at low cost.

Jan 1, 2009

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By A T. Bernardes

Using the cellular automata computational technique it was possible to simulate the generation and discharge of an iron ore pellet pile inside a direct iron reduction oven, as well as to calculate the reduction degree of the pellets as they leave the oven. It allows simulation of the variation of operational parameters and verify the results of those variations in the pellet reduction degree. The simulated data was validated in two instances: for the dynamics of the pellet flow inside the oven it was used in an acrylic bi-dimensional silo; and data from direct reduction iron literature was used for validation of the pellet reduction. The simulated results were considered acceptable to describe the movement of the iron pellet inside the direct reduction iron oven and to describe the iron pellet reduction direct in the oven.

Sep 26, 2011

By D Whitworth

The Golden Pig mine has embarked on a diamond drill program design philosophy that increases flexibility of the program by greatly increased drill pattern densities. The use of standard broad pattern diamond drilling at the Golden Pig mine has previously lead to operational inefficiencies and impacted significantly on the costs of the mine. The diamond drill program philosophy and its interaction with mine planning is explained. The case study of the E lode mining as used to internally justify the increased drill densities is detailed.

Jan 1, 2002

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By J Lyons, S Baker, D MacHunter, D Pepper

Mineral processing plants require a storage buffer to bridge differences in production rates between mining and processing. Where coarse ores are processed, such as coal or hard rock, this buffer may be an ore stockpile or silo. For wet-mining processes, eg dredging or hydraulic mining, or where fine ores are slurried close to the mining face, a surge-bin is used to contain the plant feed and smooth out the variations in mining rates. These bins have gradually evolved from simple storage vessels to units that are now frequently part of the mineral separation process itself, such as providing a desliming function to remove deleterious ultrafine gangue. This feed conditioning is often essential to achieve the levels of plant performance required in times of declining ore grades and or where inherent ore characteristics make separations harder to achieve. To achieve these dual roles requires careful consideration of bin design factors such as geometry and lining selection and increased use of instrumentation and advanced, or remotely supervised, control systems. All this ensures they provide capacity to smooth out variations in mining rates and guarantees that when conditioning ores or adjusting slurry densities ahead of the plant it is achieved without loss of valuable minerals. This paper examines the evolution of the modern surge-bin from a simple, so called, constant density tank with its inherent mass-flow compromises, limited feed preparation and beneficiation abilities, and footprint penalty, to a current state-of-the-art surge-bin, the LFCU, with a control system which provides demonstrable steady outputs, while conditioning and in some cases beneficiating the ROM material and all from a highly compact unit. It further discusses their use in other applications around the world, for example providing the necessary security for long distant high-density pumping systems; constant high density, low water usage, tailings disposal pipelines and high capacity ultrafine iron ore beneficiation.

Aug 24, 2022

By C Nyoni, T Nguyen, C R. W Seymour, G D. Dempers

Unplanned dilution directly adds cost to production from mining, milling, tailings disposal and administration. Additionally, unplanned dilution decreases the productivity, profitability and may affect the planned life of mine. Identifying and quantifying the potential for unplanned dilution allows optimisation of the mining plan and mining practices to minimise the adverse impact on productivity and the cost of production. The Dilution Rating System (DRS) has been developed to more accurately predict dilution thickness and the variable potential for dilution, from individual stopes to life of mine planning. The DRS utilises the methodology developed for the Mining Rock Mass Model (Seymour et al 2007, Jenkins et al 2009) to generate a three-dimensional dilution rating model, which is then calibrated against stoping performance. Dilution can be predicted more accurately and the parameters affecting dilution can be determined and minimised through improved mining techniques, for example blasting and ground support design. Potential high dilution areas can be identified in the planning stages of the mine and systems put in place to mitigate the risk of excessive dilution. This paper presents the methodology used to develop the DRS and then successfully predict dilution for both the hangingwall and footwall of stopes at the Gara Gold Mine. This has enabled the expected dilution to be more accurately predicted and mitigated where possible thus reducing unplanned dilution.

Mar 15, 2021