Search Documents

By Sidney G. Parker, Jack E. Pinnell

Cubic ZnSe crystals have been grown with HCl, HBr, and I, as chemical transport reagents. The growth of large, well faceted crystals is in the order HCl < HBr < I, with some produced by I, transport being 1 cm on an edge. ZnSe:I crystals showed no strain in cross polarized light and were homogeneous as determined by electron microprobe. These ZnSe:I crystals had a mobility at 25°C of about 300 sq cm per v-sec and contained 103 dislocations per sq cm; further, these crystals were pure cubic and showed both photolumi-nescence and photo conductance. Doping was attempted during crystal growth. ZnS and Zn (S,Se) crystals were also grown by I, transport. ZnSe crystals have been grown by most of the common techniques.1"6 Of these, chemical vapor transport as developed by Kaldis2 showed promise of producing high perfection, cubic ZnSe. With chemical transport, crystals can be grown far below the transition temperature for conversion of cubic to hexagonal structure. A small temperature gradient between source and growth region tends to allow near equilibrium growth, which should lead to good crystalline perfection. Because it is necessary to form volatile compounds, halogens or their compounds are extensively used as transport agents. HCl, HBr, and I, were compared as transport agents for growth of ZnSe crystals. Doping during crystal growth was attempted. ZnS and ZnSxSe1-x crystals were also grown by chemical transport. Electrical and optical properties of the crystals were examined. EXPERIMENTAL Fig. 1 is a sketch of the growth apparatus, which was a modification of Kaldis&apos;. A quartz rod which butted against the seed crystal served as a heat sink to promote growth only on the seed. Initially, crystal growth was attempted with ZnSe prepared by wet chemical methods. Because such a material contained oxides and selenates, HC1 reacted with these oxygen compounds to form H2O and no ZnSe transport occurred. Further, this ZnSe contained about 10 ppm Cu plus other impurities. High purity ZnSe, containing small amounts or no oxygen compounds, was prepared by reaction of H2Se with zinc vapors at 600° to 800°C in an atmosphere of palladium diffused H2.7 The ZnSe thus produced was usually copper free and contained only 1 ppm by weight of magnesium as determined by emission spectrographic analysis. G.E.&apos;s electronic grade ZnS, which had about 10 ppm metallic impurities, was used without further treatment. ZnS-ZnSe charges were prepared by mixing the two compounds together, then sintering 24 hr at 1100°C in an H2S ambient. The gases, HBr and HC1, were commercial grade, of 99.9 pct purity, while the I2 was 99.999 pct pure. The single crystal seeds with (111) faces for growth were mechanically held in place by sealing the outer quartz tube to the growth tube. After the charge was introduced, the system was outgassed at l0-5 torr while heated to 500°C. The desired quantities of transport reagents were then sealed off in the system, which had been cooled to 25°C. The growth tubes were inserted into a furnace with the desired temperature and thermal gradient. The system was allowed to cool for 1 to 12 hr from growth temperatures of about 850" to 25°C. The tubes remained stationary during crystal growth. HCl CHEMICAL TRANSPORT GROWTH Preliminary runs with HC1 had a temperature gradient of 100° to 200°C and no seed or heat sink. Only small crystals were obtained in these experiments as

Jan 1, 1970

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By David B. Scott

The Mogollon mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent. of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. Location and Topography The town of Mogollon is 75 mi. (121 km.) by a poorly located highway ,. from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western slope of the Mogollon Range. The main canyons i run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the mines are generally dry. The mountain ridges between the canyons have altitudes varying from 7000 to 10,000 ft. (2130 to 3050 m.) and drop sharply, on their western face, to the floor of the San Francisco Valley at an elevation of 5000 ft. (1525 m.). Erosion has been rapid, and the

Jan 1, 1920

By L. G. Sprague

The fact that this latest and most modern of the Universal Atlas Cement Company&apos;s plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product Liner. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company&apos;s property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1948

By B. L. Landrum, P. B. Crawford

Theoretical and potentiometric model studies have been made of the effect of non-uniform lateral permeabilities on pattern sweep efficiency and production capacity in waterflood and gas-cycling programs. It is shown that a diflerence in directional permeability by a factor of three may result in a sweep efficiency of only 43 per cent for a five-spot pattern or a sweep of either 79 or 38 per cent for a direct line-drive square pattern, depending on the direction of the line-drive flood. Changes in the pattern conductivity varied from about 0.8 to 1.34 over this same permeability variation, depending on the pattern used. It is suggested that measurements be made to determine the possible magnitude and extent of the directional permeability phenomenon early in the field developinent and certainly prior to the initiation of any fluid-injection progmm. INTRODUCTION Irregularities in reservoir sand properties long have been a major difficulty to anyone attempting to explicitly describe the field characteristics of oil production. In particular, it is well known that vertical and lateral permeabilities often differ appreciably; however, the existence of large regions with lateral permeabflity variation is not widely recognized. A number of years ago, extensive studies were conducted by the Secondary Recovery Research Labcratory of the Pennsylvania Grade Crude Oil Association, primarily on the Bradford field. Johnson and Hughes&apos; reported a permeability trend in the northeast-southwest direction. They indicated that flow in the preferred direction may be 25 to 30 per cent greater in that direction than in the northwest-southeast direction. They also reported that similar effects may be found in other nearby fields. The origin of the permeability variation has been discussed by Griffith Hutchinson&apos; described the results of labora- tory tests on limestone cores, pointing out that per-ferential directional permeabilities were significant in one-half of 10 formations studied and that the average permeability ratio was 16:1. Barfield, Jordan and Moore analyzed the fluid-injection displacement performance in the Spraberry and reported that the effective ratio of permeability parallel to the major axis to the permeability perpendicular to this axis was 144:l and that it inclined along an angle of about 30". To prevent the reduction of sweep efficiency which would normally result from flooding or cycling in such reservoirs, well spacing could be varied from the customary square to a diamond-shaped pattern. Johnson and Hughes&apos; presented a method for determining the desired shape. Another method will be discussed in detail in the next section. It is the purpose of this paper to investigate quantitatively the effect of directional permeability upon the sweep efficiency and production capacity of the five-spot and line-drive well patterns. Information currently in the literature will be applied to this particular problem and augmented by a potentiometric model study. It is stressed that the effects herein discussed may or may not be of great importance because field data on this phenomenon are far too scant to form such an opinion. It is suggested that, if conditions similar to those found by Johnson and Hughes frequently exist (as may well be the case), more consideration cdrtainly should be given to this problem.

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric&apos;s Compax® and Stratapax® and Megadiamond&apos;s Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot&apos;s reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By C. O. Lee, R. H. Feierabend, Z. W. Bartlett

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.&apos;.&apos; Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.&apos; Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By W. F. Kieschnick, C. C. Miller, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor&apos; have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By H. L. Stone, A. O. Garder

A numerical method of solving the partial differential equations which describe the one-dimensional displacement of oil by gas has been presented. Possible extension of the method to treat multidimensional flow is discussed, and the limitations of this extension are indicated. Using this method, it is possible to allow for the existence of a gas cap, the presence of any number of gas-injection or oil-production wells and the evolution of dissolved gas from the oil. It is also possible to allow for variation in the cross-sectional area, elevation, porosity and permeability of the reservoir. The influence of relative permeability and the force of gravity in the direction of flow upon the displacement is considered. The influence of capillary pressure upon the flow and the effect of gravity in the direction perpendicular to flow are neglected. The physical properties 01 the fluids are considered to be Junctions of pressure only, and equilibrium between contiguous phases is assumed. The numerical calculations can be readily carried out by the use of a digital computer. Several example analyses have been performed using the IBM 704 computer, and about one-third of an hour of computing time was required per case. Reservoir behavior predicted by use of this numerical method was compared to data obtained by other methods for three cases — complete pressure maintenance, dissolved-gas drive and gas-cap drive. The independent solutions to these problems were obtained by analytical solution, laboratory experiment and field data, respectively. Agreement of the numerical solution with data from these sources was good; this agreement establishes the convergence and accuracy of the numerical method. INTRODUCTION Most petroleum reservoirs can be produced by any one of several alternative programs. When a reservoir is produced by primary methods, production economics can be influenced by controlling the number and location of wells and the flow rate of each well. An even greater influence may be achieved by augmenting the recovery of oil obtainable by primary methods. This can be accomplished by injection of fluids such as water, natural or enriched gas or a bank of light liquid hydrocarbons. Selection of the most desirable operation requires a means of predicting the reservoir behavior which will result from each of the several alternative programs. The purpose of this paper is to present a mathematical method for predicting the behavior of reservoirs produced by gas-cap drive, dissolved-gas drive or pressure maintenance by gas injection. The method described herein takes cognizance of phase changes caused by a decline or an increase (due to gas injection) in reservoir pressure, of the presence of a gas cap and of the effect of gravity on the flow of gas and oil. Relative permeability relationships are used to define the flow properties of the rock. Allowance is made for variation in cross-sectional area, elevation, permeability and porosity of the reservoir. Both the influence of capillary pressure upon the flow and pressure gradients in the gas cap are neglected. Whenever a liquid phase and a gas phase are in contact, they are assumed to be in equilibrium. The physical properties of the fluids are considered to be functions of pressure only. Therefore, if the method is to be used to predict the effects of a gas-injection program, mixtures of the injected gas and formation crude should-have the same physical properties as mixtures of formation gas and crude. The equations to be presented in this paper apply only to a one-dimensional case; therefore, they neglect the influence of gravity in the direction transverse to the flow. As is well known, this gravitational influence may lead to overriding of oil by gas. Consequently, this procedure as presented is most applicable to long, thin reservoirs for which gravity overriding is not important. On the other hand, the equations presented can be generalized to treat multidimensional flow and, hence, to consider gravity overriding, if desired. A word of caution on two points is advisable here, however. First, the authors have not demonstrated the accuracy of the numerical technique for multidimensional flow. Second, and more important, capillary pressure will often be of importance in multidimensional problems. Obviously, in such cases a generalization of the

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.&apos; Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts&apos; Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg&apos;s method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By A. E. Bibb, J. R. Fascia

Single-crystal wafers of zirconium have been exposed to 680°F neutral water. The single crystals were of known orientation and weight-gain data as a function of crystal orientation were obtained. These data show that all the crystal faces studied obeyed a cubic rate law out to the time of transition whereupon the crystals corroded at an approximately linear rate. The time to transition varied from 114 days for (1074) crystals to about 325 days for the (2130) faces. The epitaxial relationship be-tween metal and monoclinic oxide was found to be (0001) H (111) and [1120] 11 [101]. A black tight adherent oxide layer was formed on the crystals in the pretransition range. This black oxide was found to be monocrystalline. The white corrosion product produced after transition was found to be polycrys-talline but highly oriented. X-ray line-broadening studies found that the black oxide was a highly strained structure whereas the white oxide was relatively strain-free. These results indicate a strain-induced re crystallization or fragmentation accompanies the change from protective black oxide to nonprotective white oxide. ZIRCONIUM alloys have been used quite extensively in high-temperature aqueous environments. Alloy additions can be made to commercial sponge zirconium which enhance the corrosion resistance of the zirconium in both water and steam media, which raise the tolerance limit for certain impurities detrimental to corrosion resistance, and which reduce the amount of free hydrogen pickup during corrosion. The development of the corrosion-resistant zirconium alloys has been a long and tedious job involving trial and error methods. This technique has been necessary because of a lack of fundamental data and hence understanding of the corrosion mechanisms. The objective of the work described herein was to provide some fundamental data with respect to the aqueous corrosion of zirconium crystals as a function of the orientation of the exposed surfaces. Hg. The zirconium chunk was then cooled to below the transformation temperature (862°C) and reheated to 1200°C for 8 hr. The ultimate size of the zirconium grains increased with the number of cycles. Rapid or even furnace cooling through the transformation temperature produces a considerable amount of substructure which was intolerable in corrosion experiments as it would be in the study of any crystallographically dependent property. It was found that a high-temperature a-phase anneal for approximately 4 days reduced the substructure below the limits detectable by visual or X-ray means. Crystals so produced were carefully cut from the massive zirconium chunk and oriented by standard back-reflection Laue techniques. The crystals were then mounted in a goniometer head and, by using the three degrees of freedom available, slices on the order of 0.015 to 0.020 in. were cut parallel to any desired crystal plane. These slices were then carefully polished on both sides to produce smooth flat faces, pickled to remove about 0.002 in. per face, annealed for 1/2 hr at &apos;750°C in a vacuum of approximately 10"5 mm Hg, flash pickled, and checked for orientation. The pickling solution was 45-45-10 vol pct HN0,-H20-HF and continuous agitation was provided to eliminate pitting of the slices. Any slice that was not within 2 deg of the desired orientation was discarded, and any evidence of substructure as indicated by the Laue spots was also grounds for discarding the sample. Thin slices were used for the corrosion tests because weight gain per area data could be obtained with only a minimum area exposed to the corrosive media that was not of the desired orientation. The thin single-crystal slices were of irregular shape and as a result the areas were determined by placing a crystal inside an inscribed square of known area, enlarging a picture of this assembly about X5, and tracing both the enlarged square and crystal with a planimeter. The zirconium used to produce these single crystals was crystal-bar grade, a typical analysis of which is given in Table I. An oxygen analysis on prepared crystals gave a concentration of 205 ppm. The hydrogen concentrations are believed to be less than 15 ppm due to the dynamic vacuum anneal given each crystal. Typical nitrogen values for zirconium treated in this manner are about 10 to 20 ppm. RESULTS AND DISCUSSION Single-crystal wafers have been exposed to de-oxygenated, deionized water in static autoclaves.

Jan 1, 1964

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800&apos; to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.&apos; The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.&apos; There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.&apos; The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By J. W. Halley

RIMMING steels derive their name from their action during solidifica-tion in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop ill the molds, are deter-mined by the Composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accu-rately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring condi-tions and furnace practice on the distribution, though there is still much to be done in this direction.

Jan 1, 1938

By O. G. Kiel, G. W. Swift

The concept of "a continuous succession of steady-states", which has been applied successfully by Aromfsky and Jenkins to obtain a solution for the nonlinear partial differential equation describing the transient Darcy flow of gas through porous media, is demonstrated to be equally valid for transient non-Darcy flow. A mathematical model, which numerically solves the partial differential equation, is used to check the validity of the succession of steady-states solution. Comparison of sand-face pressure histories compelted by the two methods shows excellent agreement. The utility of the succession of steady-states solution in predicting performance of gas wells rests in the fact that no special computation equipment is required. The development of the succession of steady-states solution leads also to a practical method for determining and analyzing field test data. A method for taking gas-well test data under constant-rate conditions is presented. Experimental data obtained in the field by employing the constant-rate method are presented and analyzed in accordance with the succession of steady-states solution. Analysis of data in this fashion is demonstrated to give direct "in situ" information for reservoir permeability, porosity and turbulence or non-Darcy coefficient. INTRODUCTION The economics of gas production are dependent upon the transient behavior of flow within the reservoir. For production from a finite reservoir, the transient flow behavior can be subdivided into two parts. At first, the transient caused by the movement of the pressure "wave" into the reservoir is of importance. Later in the production history, the pressure-wave movement ceases and the second transient stage of material depletion becomes controlling. For reservoirs of relatively high permeability, it can be shown that the pressure wave moves into the reservoir and stabilizes quite rapidly. In the case of relatively impermeable reservoirs, quite the opposite is true. Although it is theoretically possible to compute the production capability of a well from the properties of the reservoir as determined by static tests and core analyses, more reliable information is obtained by conducting flow tests on the well and thereby obtaining some measure of "in situ" formation properties. For gas wells, there are two basic types of tests in existence: the flow-after-flow method,&apos; and the isochronal method.&apos; Both of these techniques are tailored to obtain data that can be analyzed in accordance with the empirical performance equation: In addition, the isochronal method makes provision for the sluggish nature of pressure-wave movement in "tight" formations by requiring pressure build-up between flows and by stipulating that data obtained on successive flows be analyzed at equal elapsed flow times. It can be demonstrated that either test is valid for reservoirs of high permeability. Further, since it has been pointed out that the pressure wave stabilizes rapidly for reservoirs of this type, tests of relatively short duration will give stabilized information on the performance of a well. Further decline of sand-face pressure and/or production rate may be determined by employing material-balance techniques. Cullender&apos; points out that for relatively impermeable reservoirs the flow-after-flow method gives invalid results. (See Appendix C.) If the isochronal method of testing is used, there are two alternatives: (1) the tests must be conducted for a sufficient length of time to obtain stabilized information (which may require months to accomplish); or (2) some method for extrapolating the results of short-term isochronal tests must be employed. The first alternative is impracticable because of manpower, conservation and economic considerations. Recourse to the second alternative requires some assurance regarding the reliability of the extrapolation technique. Poettmann and SchilsonJ present an empirical method for predicting stabilized performance. The present investigation was originally initiated to determine the reliability of this technique. To do this, a mathematical model was developed to simulate the Darcy and non-Darcy flow of gas through porous media. The model consisted of a finite-difference approximation of the nonlinear partial differential equation which was solved on an IBM 7090 computer. Long-term production histories were simulated by the model and compared against predictions obtained from the Poettmann-Schilson method. As the work progressed, it became apparent that a straightforward predictive equation could be developed by utilizing the concept of a succession of steady-states. As a result, the emphasis of the work was redirected to exploit the advantages of the new method.