Search Documents

By Oscar M. Wicken

The mineral magnesite (MgCO3) if pure would consist of 47.7 pct MgO and 52.3 pct CO2. It is one of the calcite group of rhombohedral carbonates which includes calcite (CaCO3), siderite (FeCO3), rhodocrosite (MnCO3), and smithsonite (ZnCO3) among others. The members of this group enter into a wide range of substitutional solid solutions, whose range is still imperfectly known.* MgCO3 and FeCO3 appear to form a complete series of which breunnerite (ferroan magnesite) is a well known variety. Because of the considerable difference in size of the Ca and Mg ions, there is only a limited range in substitution in the MgCO3-CaCO3 series. (Dolomite, not strictly a member of the calcite group, may be regarded as an ordered structure developed when Ca: Mg is approximately 1:1.) The practical consequence of these relationships is that the lime carbonates (calcite and dolomite) are commonly present in magnesite deposits chiefly as mechanical mixtures. Magnesite may be either crystalline or "amorphous" (cryptocrystalline). The crystalline form has a hardness of 3.5 to 4.0. The color may range from white to black through shades of yellow, blue, red or gray. It is rarely found pure but generally contains variable amounts of iron, lime, and silicate minerals. Color cannot be used as an index of purity except under specific local conditions in a single quarry. In a given quarry an experienced man may be able roughly to grade magnesite by intuitively assessing such features as crystallinity and color. Crystalline magnesite occurs in larger deposits, but the cryptocrystalline variety is more common. The latter is fine-grained and compact and shows no cleavage; often it is descriptively called "bone magnesite." The fracture is usually conchoidal, and hardness is 3.5 to 5.0. It is normally white, but sometimes it is light yellow to orange or buff because of included impurities. In addition to lime and iron, which may be present in small amounts, silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. In general, commercial deposits of "amorphous" magnesite have lesser amounts of accessory minerals than does crystalline magnesite. The specific gravity of "amorphous" magnesite is 2.90 to 3.0. Pure, crystalline magnesite has a specific gravity of 3.02, but iron carbonate, commonly present, raises the specific gravity to somewhat higher values. Magnesite dissociates, when sufficiently heated, into magnesia (MgO) and carbon dioxide. Either simultaneously or upon further heating the magnesia develops a crystalline structure identical with that of the natural mineral, periclase, which occurs sparingly in nature but not normally in workable deposits. Brucite is another magnesium mineral capable of being directly reduced to magnesia by heat alone. Brucite (Mg(OH)2) has been mined for the production of various grades of magnesia. It theoretically contains 69.1 pct MgO and 30.9 pct H2O. It may be white, but is generally blue or green with a gray cast. It has a translucent appearance. The mineral is soft (hardness, 2.5), and has a specific gravity of about 2.4. Nomenclature of Products The word "magnesite" literally refers to the natural mineral, but common usage has applied it plus a prefatory word to two other

Jan 1, 1960

By G. W. Geil, D. H. Woodard, W. D. Jenkins

In a series of papers, the authors and their associates have shown the influence of four important factors on the technical cohesion limit.3-l6 By "technical cohesion limitv is meant the technically determin-able resistance to fracture. The four importarlt factors are the stress system, plastic deformation, temperature, and the strain rate, The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. The previously mentioned series of papers contains ample evidence that plastic extension increases the fracture stress of any polycrystalline metal, In a recent paper of the series,l5 moreover, it has been shown that the effect of plastic deformation on the fracture stress cannot be attributed to reorientation of internal flaws but is a work-strengthening effect, similar to the effect on the flow stress, $ Plastic deformation of steels, however, may not only cause work hardening, but may result in additional hardness because of strain aging. Some evidence that strain aging affects not only the flow stress but also the fracture stress, has been presented in a recent paper.14 In that paper, a study is made of the influence Of Plastic deformstion at room temperature on the fracture stress of ferritic steels at -188°C. The study is based on the results Of two-stage tests. In the first stage each specimen was extended a predetermined amount at room temperature; in the second stage the specimen was tested to fracture in liquid air. In most Of these tests the specimen remained in the testing machine during the interval of about one hour between the first and second stages, it was kept under a tensile load of about 500 lb and maintained at liquid air temperature. The effects of various amounts of .plastic deformation on the fracture stress were thus determined and curves were obtained to represent the influence of plastic deformation at room temperature on the stress at brittle fracture in liquid air.14 Two specimens Of ingot iron, however, were removed from the testing machine at the end of the first stage and several days elapsed before the specimens were tested to fracture in liquid air, As shown in Fig 8 of that paper," the points representing fracture of these specimens are far above the curve representing the results of two-stage tests without a rest interval between the stages. The evidence thus indicated that the fracture stresses of these two specimens were increased not

Jan 1, 1949

By Y. H. Liu, G. W. Powell

Thin foils made from the gold-rich region of- short (0.15 mm)Au-Ag diffusion couples annealed at 880°C for 1 hr were examined in ax electron microscope and the structures were compared with that of pure gold subjected to identical heat treatments. The couples underwent Plastic deformation (bending) during the diffusional anneal. The foils prepared from the diffusion zone have a higher dislocation density and incidence of subboundaries than pure gold. The plastic bending of the couple can be interpreted in terms of the climb of edge dislocations, which are pavallel to the bend axis, along the direction of diffusion. THE interaction of lattice defects during interdiffu-sion between two metals has been considered by several investigators. In particular, da Silva and Mehl,1 Barnes,' and Bardeen and Herring3 have proposed models based on interactions between point and line defects to account for the Kirkendall effect (marker movement). Each of these models is based on dislocation climb, which can either add or remove lattice planes, induced by an under- or supersaturation of vacancies. A theoretical treatment of the nucleation and growth of voids by the condensation of vacancies has been presented by Seitz.4 Stresses can arise in a binary diffusion couple as a result of the vacancy flux and the gradient in the lattice parameter. rinkmman' has investigated the effects of diffusion-induced stresses on void formation; the results of his analysis suggest that voids can form and grow under the influence of these stresses in the absence of an excess vacancy concentration. The relationships between vacancy supersaturation and diffusion-induced stresses and void formation have been elucidated also by Balluffi and seigle6 who concluded that the stress generated by a vacancy supersaturation aids the growth of voids. Experimental evidence which indirectly shows that stresses are produced by chemical diffusion has been obtained by several researchers.2,7-9 This evidence consists in part of the observation by light microscopy of the formation of subgrains, a process characteristic of the high-temperature deformation of some metals during creep.'0 More striking, however, is the plastic bending of short (0.2 mm) Cu-Ni couples observed by Barnes2 and of boron-doped silicon crystals reported by Queisser.9 Diffusion-induced dislocations in iron and silicon have been investigated by Ainslie et a1.11and Schwutte and Queisser,12 respectively, the former using transmission electron microscopy and the latter an X-ray transmission technique. Matthews and Crawford13 observed the formation of boundaries by the climb of interfacial misfit dislocations in thin, vapor-deposited Au-Pd couples diffused in situ in an electron microscope. In order to obtain additional information on the phenomena associated with defect interaction and diffusion-induced stresses in binary couples, an electron transmission study of foils prepared from the diffusion zone of short Au-Ag couples was undertaken. The initial objective was to investigate the processes occurring at various points of the diffusion zone. Subsequent research demonstrated that foils could be prepared only from the gold-rich region of the diffusion zone using the technique described herein. EXPERIMENTAL PROCEDURE Preparation and Annealing of the Diffusion Couples. The couples were made from annealed, high-purity (99.999 pct). polycrvstalline gold and silver sheets (0.075 mm thick). Shall (0.075 by 5 by 17 mm) elec-tropolished coupons of gold and silver were pressure-bonded by heating the two metals in a graphite device to 770°C and holding at this temperature for approximately 30 min. The quality of the bond was ascertained by metallographic examination at 150 times. Each couple subsequently was annealed at 880°C for 1hr; under these conditions, the extreme portions of the

Jan 1, 1968

By W. H. Emmons

Although gold is one of the rarer metals, it is widely distributed; it is found on all of the continents and in each of the grand metallogenic provinces of the earth. It is prominent particularly in the shield areas of the earth; these areas have produced a large part of the world's lode gold and in most of them gold lodes are more important than the lodes of other metals. The Scandinavian shield is the only one that has not produced much gold. Nearly all of the world's gold has been derived from lodes and from sands and gravels where gold placers formed by the destruction of lodes. The gold derived from magmatic segregations, from pegmatites and from contact metamorphic deposits is quite subordinate to that derived from auriferous lodes. The lodes include all veins and related deposits that are formed by hot waters that move along fissures or other openings and that deposit vein 'matter :in the fissures and by replacement of the country rocks along the fissures. All of the shield areas of the earth are characterized by large areas of granitic rocks including granitic gneisses, granodiorites and other acid intrusives which here are included in the general term "granite." The granites are intruded into schists, ancient lavas and other rocks which here are designated as the "invaded" rocks. The granites are parts of what once were great batholiths: that is, they are the remaining portions of great deep-seated bodies that slope outward, have very irregular roofs and so far as known have no floors but extend downward to great though unknown depths. Some of them are scores or hundreds of miles across and contain islands or "roof pendants" of the invaded rocks at places where the roofs of the batholiths were low—that is, where erosion has not yet completely unroofed the batholiths. It is in these islands of older rocks and in the narrow marginal belts and cupolas of the batholiths that practically all of the gold lode deposits of the shields are found. Valuable lodes are lacking generally in the granites themselves except in grahite within a mile or less from .the contacts with rocks of the islands (Fig. 1). It is probable that the great areas of granites and gneisses that surround the islands are not all of the same age, and that at places unmapped granite intrudes gneiss or older

Jan 1, 1932

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By H. P. Rassbach, E. R. Saunders

MUCH progress has been made in recent years in the theory and practice of making stainless steel. By effective utilization of oxygen for decar-burization and more suitable alloying agents, it has been possible to attain consistent production of very low-carbon stainless steel. In order to facilitate economical production of stainless steels, the Electro Metallurgical Co. has carried out an extended experimental program that has clarified some of the complex interrelations of temperature and composition under decarburizing and reducing conditions. These results'-:' have been founded in large part on small experimental heats, and in order to confirm their validity and significance under commercial conditions, a survey of stainless steel melting practice has been made with the cooperation of stainless steel producers. Conditions required for decarburization and associated oxidation of chromium, manganese, and iron have been fairly well established in relation to the beneficial effect of the highest practicable temperature. The recovery of chromium and manganese from highly oxidized slags by reduction with silicon has been indicated with somewhat less precision and this study has shown significant deviation in large commercial heats from the small experimental heats. In spite of an unsatisfactory degree of accuracy in estimating the conditions affecting reduction of metallic values, it has been possible to calculate a slag weight in reasonably good agreement with the results observed in large heats. While there still is much to be learned about both the qualitative and quantitative aspects of stainless steel melting, this survey has indicated the manner by which the efficiency of the production process may be measured. Oxidation Period In order to establish practices for the recovery of chromium and manganese from the slag the amounts of these metals oxidized should be known. Moreover, since reduction of oxidized chromium and manganese must necessarily be accompanied by similar reduction of iron, knowledge of the total quantity of metallics oxidized is essential. The relations between carbon, chromium, and temperature under oxidizing conditions were developed by Hilty in 1948.' While it had been realized previously that retention of chromium in the metal during carbon oxidation is favored by high temperatures, the Hilty relation provided quantitative information useful for evaluating melting procedures. For example, it was shown that decarburization to moderate carbon levels can be achieved while retaining substantial amounts of chromium. However, in decarburizing to the low-carbon level necessary for producing 0.03 pct maximum carbon stainless steel, very little chromium remains in the bath at the temperatures generally employed. For this reason, Hilty, Healy, and Crafts' later projected an extension of the chromium-carbon relation to the low-chromium region. Although this chromium-carbon-temperature relation defined the composition of a chromium steel bath at the end of the oxidizing period, it did not provide a direct means for estimating the total amount of metallic oxidation occurring during decarburization of a stainless steel heat. This subject was investigated by Crafts and Rassbach³ and, later, by Hilty, Healy, and Crafts" who demonstrated that metallic oxidation is a function of the chromium content of the initial furnace charge, the minimum carbon content attained, and the temperature. It was further demonstrated from data on 1-ton heats that an empirical relationship exists between the ratio of chromium plus manganese to iron in the slag (S) to the corresponding ratio of these components present in the metal bath. The following expression was derived to permit the calculation of the amount of metallics oxidized during decarburization of a given charge: W-2000 (Cr1 + Mn1)-(Cr2 + Mn2) 1 100s/s+1-(Cr3 + Mn2) where W is the pounds of chromium, manganese, and iron oxidized per ton of charge; Cr1, the percentage of chromium in the charge; Mn1, the percentage of manganese in the charge; Cr2, the percentage of chromium in the bath after oxidation; Mn2, the percentage of manganese in the bath after % Cr + % Mn oxidation; and S =%cr+ % Mn/%Fe in the slag after %Fe oxidation. In order to establish whether the slag ratios of commercial heats are consistent with those found in the experimental heats, the slag and metal analyses shown in Table I were evaluated. These data represent samples taken after the oxidation of two 1-ton and seven 15 to 25-ton heats of types 303, 304, and 304L stainless steel made in chromite, acid, and basic hearths. Fig. 1 illustrates that the results for the commercial heats correlate reasonably well with the relationship originally established for experimental 1-ton heats. It will be noted that in the range of metal composition of these heats, the slag values generally lie above the line. As was suggested by

Jan 1, 1954

By S. A. Spachner

An analysis of the powder patterns of the omega transition phase in three binary titanium alloys containing 8 pct Cr, 13 pet Mo, and 15 pet V, respectively, showed that all could be indexed on an orthorhombic unit cell. The unit-cell dimensions were all quite similar. There is evidence for the occurrence of more than one transition phase in Ti-Cr and Ti-V alloys. FOLLOWING the discovery of a new brittle phase in certain titanium-chromium alloys by Frost, Parris, Hirsch, Doig, and Schwartz,' named ? by these investigators, much interest has developed concerning the identification of alloy systems in which this phase exists, kinetics of the transformation in such systems, and the crystal structure of the ? phases appearing. Omega has been found in alloys of titanium-manganese, titanium-molybdenum, titanium-iron,' and titanium-vanadium.' In the present work, a study was made of the powder patterns of the ? phase occurring in alloys of Ti-8Cr, Ti-13Mo and Ti-15V in an effort to obtain a basis of comparison for ? phases appearing in these different alloys. Comparison of Alloys for ?-Phases Two hundred mesh powders of Ti-8Cr, Ti-13Mo and Ti-15V were prepared. A portion of powder sufficient for three x-ray powder specimens was placed in a Vycor tube, evacuated to less than 0.1 µ pressure, filled with argon, and sealed. The tubes were then heated to 900°C, held at this temperature for 30 min, and water-quenched. Following this transformation to the ß phase, the specimens were quenched in lead or solder pots, held at the desired temperature for varying lengths of time and water-quenched. The heat-treatments used and the phases identified are listed in Table I. The intermediate water quench was used in lieu of direct downquenching from 900°C to the bath temperature desired to circumvent the possibility of transformation of the powder specimen from ß to (ß + a) while it was being moved from the homog-enization furnace to the lead bath. To check the possibility that upquenching to the bath temperature might bring into play a different mechanism than downquenching to this temperature, resistivity measurements were compared on Ti-8Cr rod specimens which were transformed isothermally at 400°C by downquenching from the solution-treatment temperature and those which were transformed at 400" C by upquenching ß specimens from room temperature. The results are shown in Fig. 1. No difference in transformation mechanism was noted. It soon became apparent that sufficiently detailed Debye-Scherrer photograms of the ? phase in the alloys which were to be used could not be obtained by the use of copper radiation. Although satisfactory photograms of ß and ß + a phases were obtained with this radiation, the ? phase appeared to exhibit mild fluorescence, making interplanar spacing computation virtually impossible. Molybdenum radiation appeared to offer promise in cutting down this fluorescent effect, the mass absorption of titanium for molybdenum radiation being 23.7 in contrast to 204 for copper radiation. The reduction in the accuracy in determining the location of the photo-gram lines caused by the shorter wave length of molybdenum characteristic radiation did not appear to be a significant factor. Utilizing a camera of 57.3 mm radius, best results were obtained for exposure times ranging between 30 and 40 hr. Tube potential

Jan 1, 1959

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By W. A. Backofen, D. H. Avery, W. F. Hosford

Sheets of the magnesium alloys AZ31B, HK31A, and ZE10A in several different tempers were tested in tension and determinations were made of the ratio of width-to-thickness strain. A marked increase in the ratio with tensile straining and a dependence upon alloy and test direction are rationalized in terms of a balance between the amounts of basal and prism-plane slip. All such variations are related, in turn, to the prevailing crystallographic texture. Fracture appearance is explained on the basis of anisotropy in plastic flow, and implications for developing texture -hardening effects in these alloys are discussed. ThE crystallographic texture or preferred orientation of a given material is determined by details of processing history. Such texture is known to influence many aspects of material behavior, in particular both the yielding and strain-hardening characteristics which are of special interest in the present work. Traditionally, the resulting plastic anisotropy has not been regarded as especially desirable. Earing in drawn sheet is perhaps the most common example of an unwanted effect of texture. However, it has also been recognized that suitable textures may be usefully employed to improve drawability,1,2 as a specific example, and generally to control yielding resistance under combined-stress loading.374 Texture would seem to be a detail of structure not yet exploited to nearly the fullest extent. A convenient basis for characterizing anisotropy in plastic behavior is the ratio of width-to-thickness strains obtained in a tension test;5&apos;6 the parameter is frequently labeled "R" and its value is revealing with respect to the nature of the prevailing texture. R gives a useful measure of a material&apos;s "thinning resistance". For an isotropic material, R = 1. With R > 1 the increased through-thickness strength in a sheet means greater resistance to yielding under biaxial tension, or "texture hardening";3&apos;4 if R < 1 the result may be a "texture softening" under the same loading conditions.4 Most R data relate to steel sheets for deep-drawing applications. Values for steel and other materials of cubic structures are not often much greater than 1 and nearly constant with strain in testing.1,2,7,8 To explore the implications of plastic anisotropy further, it was felt that experiments with much more strongly textured materials would be useful, and this led to the choice of magnesium alloys. The "ideal" sheet texture for magnesium contains the (0001) plane in the rolling plane, which ought to lead to R values approaching infinity. However, departures from the ideal texture, the possibility of slip in non-close-packed directions, and deformation by twinning would all be expected to introduce some range of R. Accordingly, studies on these materials were undertaken. EXPERIMENTAL Alloys in sheet form, Table I, were selected to obtain a variation in crystallographic texture, in the expectation that this would be reflected in differences in plastic anisotropy. Pole figures constructed by the Schulz surface-reflection technique9 were provided with the experimental materials by the Dow Metal Products Co. Profiles of pole density along great circles through the rolling (0 deg) and transverse (90 deg) directions were prepared from the pole figures and are collected in Figs. 1 and 2; considerable departure from the "ideal" (0001) alignment in the rolling plane is evident, with the largest angular spread in both directions being found in the ZEl0 alloy. Results of tensile tests on full-thickness specimens of 6-in. gage length by 1/2-in. width are given in Fig. 3 as engineering stress-strain curves* in rolling and transverse directions. All tests but one were made at a constant drive rate of 0.02 in. per min, and the final values of percent elongation at fracture, over the initial 6-in. gage length, are noted at the ends of the curves; one test on ZE10A-

Jan 1, 1965

By Robert E. Ogilvie, Zvonimir Ban

Oxidation experiments were conducted above 600°C to investigate the oxidation products formed on the surface of MoSi2. Results are presented which indicate that minor iron impurities play a key role in the oxidation behavior of MoSi2 above 600 °C. Based on considerations of the crystal chemistry of the oxidation products, MoSi2 with rhenium and iron additions was found to be resistant to oxidation in the pesting temperature range. AS early as 1914, Honigschmidtl observed that some silicides of molybdenum exhibited high resistance to oxidation at elevated temperatures. This fact did not arouse much interest until 1950, when Kieffer and cerwenka2 examined this property in more detail. They found that Mo-Si alloys with approximately 70 pct Mo (by weight) could be heated to 1600°C in an oxidizing atmosphere without any significant damage. The surface was found to be protected by the formation of an extremely thin silica glass layer which had no tendency to spa11 during subsequent thermal cycling. In 1955, Fitzer3 discovered that even solid bodies made of MoSi2 completely oxidized within a relatively short time when exposed to the air in the temperature range from 300° to 600°C. To describe this phenomenon he proposed the name "molybdenum disilicide &apos;pest&apos; ", clearly analogous to the previously observed "tin plague" ("tin pest") which, however, arises as the result of a phase transformation. Studies performed by Fitzer and, in particular, one published recently by Berkowitz, Blackburn, and Fel-ten,&apos; comprise the most extensive research to date on the pest phenomenon in MoSi2, as far as the fundamen- tal mechanism of the process is concerned. The first of these studies revealed the existence of a crystalline phase which appeared at the surface at 750°C and dissolved in the glassy silica layer at 1150°C. The logical assumption was that this phase was some reaction product of MOO3 and SiO2. The formation of a reaction product of this type seemed probable since it had been mentioned by Glemser and Lutz6 in a paper describing their studies of molybdenum oxides; however, this assumption was later disproved.8 It is our belief that information concerning the exact nature of this crystalline phase may be important for a better understanding of both pesting and the protection mechanism. Therefore, since the only available general description of the pest phenomenon was that of Fitzer, it was decided to reproduce his experiments. These experiments established that, in addition to the "pest" and "nonpest" temperature range, an intermediate region exists between 600" and approximately 650°C. This region is characterized by the appearance of a variable amount of yellow to orange colored crystals. The electron-beam microanalyzer was used to qualitatively determine their composition. Iron and molybdenum were found to be major constituents. This result can be explained based on the following facts: 1) iron, according to literature data,* is the most common impurity in molybdenum powder, and its content can be as high as 0.25 pct; 2) technical silicon powder usually contains iron; 3) steel ball mills are often used for the crushing and grinding of MoSi2. In order to clarify the exact role of iron, it was deliberately added to a stoichiometric mixture of molybdenum and silicon. The observed results corroborated the previous experiment, proving that iron (probably as some silicide phase) concentrates along the grain boundaries. I) EXPERIMENTAL PROCEDURE A) Oxidation of MoSi2 with Iron Additions. 1) Specimen Preparation. Specimens were prepared by both

Jan 1, 1967

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing &apos;fresh&apos; and &apos;grown in&apos; sources. &apos;Fresh&apos; dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When &apos;fresh&apos; sources are eliminated by chemical polishing the crystals have to rely on &apos;grown in&apos; sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh&apos; sources operate. Grown in&apos; sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,&apos; a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution&apos;s research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof&apos;s rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel&apos;s photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By A. D. Marlin, A. J. Gentile, E. F. Jordan

Metallurgical changes in SAE 52100 ball-bearing components resulting from overload testing are described. Changes in microstructure, hardness, and resiclctal stresses crre discussed zuitlz re.ference to material cleanliness obtained by various steel-melting practices and are compared with work by otlzer investigators. Evidence is presented to show that the initialion and development of microstruc-tural alterations are characterized by two separate reactions: the appeavance of a "dark etchingJ&apos; constituent, and "gray lines" or a light etclzing constituent. The dependency of these tzvo reactions on material cleunliness, running tirne, and contact stresses is discussed and a failure mode related to material cleanliness and microstructural transformation is proposed. THE study of ball- and roller-bearing contact fatigue has been paced by a strong emphasis on bears ing application performance. Particular attention has been paid to conditions that effect the spalling-type failure that is characteristic of rolling contact fatigue in through-hardened components. Some of the conditions investigated are lubrication and atmosphere,1-3 material characteristics and finish,475 and speed and design fa~tors."~ A typical spalling-type failure is shown in Fig. 1. The arrow shows the motion of the ball relative to the inner-ring race surface. The leading edge of the spall is usually sharper than the trailing edge. The race surface near the trailing edge also shows small dents caused by debris from the spall. In this type of testing very little metallurgical investigation is done on failed bearings. Emphasis is placed on test conditions and statistical analyses of endurance data. More basic work has been done relating micro-structural changes to fatigue performance. Dyer" and Wood, Cousland, and sargant9 have used mostly simple materials, such as single crystals and single-phase polycrystalline specimens, under simple alternating strain to identify a systematic process of fatigue damage. drutowski" was concerned primarily with the relationship between steel structure, contact stress, and energy losses in rolling contact. dones11 and Bush, Grube, and Robinson12 utilized changes in microstructure and residual stress in overload-tested rolling contact elements as a means of investigating the fatigue process. Work is being done on an ASME-sponsored contract,13 using both simple and complex materials, but there is still a long way to go before such theories as pore and void growth in simple structures can be applied to the relatively complex bearing steel microstructure. The purpose of this paper is to report on an investigation into the effect of steel cleanliness on the structural alteration and residual stress changes found in overload-tested ball bearings. Using these results and those of previous investigators, we will propose probable failure mechanisms in both overload- and normal load-tested ball bearings.14,15 PROCEDURE Ball bearings? 3208 size, were fabricated from SAE 52100 steel obtained by five different melting practices. The melting practices, chemistry, and inclusion ratings for the five lots of steel are summarized in Tables I and 11. The nonmetallic inclusion ratings were determined by the Jernkontoret method described in ASTM E45-51 Method A. This technique consists of microscopically examining a series of polished samples taken from specified locations in the ingots, billets, or bars. Each sample is surveyed at XlOO magnification and the inclusion types and sizes are compared to standard fields. Because of the nature of these ratings all values in Table I1 are rounded to the nearest half. The elec-

Jan 1, 1965

By J. E. Owen

A model of a porous body is presented in which the pore space consists of a system of voids and interconnecting tubes. Relationships between porosity and resistivity formation factor are determined partly by calculation, partly by experiment. Con triction effects characteristic of the model are shown to be sufficient to account for high formation factors. It is shown that constriction may be combined with moderate amounts of tortuosity to give model pore systems exhibiting to a first approximation porosity and resistivity properties similiar to those of natural porous bodies. INTRODUCTION The relationship between the electric resistivity of a fluid-filled porous body and the geometry of its pore space is so complex that the calculation of the resistivity of a natural porous rock is a practical impossibility. Both the resistivity of a body and its porosity are measurable quantities, however, and previous successes at relating them have been reached by an empirical approach. Efforts at obtaining theoretically derived formulae relating them have generally been unsatisfactory. One of the reasons for this may lie in the pore geometry that has been assumed. THE TORTUOSITY CONCEPT A Parameter called the formation factor is useful in dis-cussing the resistivity of a fluid-filled porous body. This parameter is the ratio of the resistivity of a fluid saturated porous body to the resistivity of the saturating fluid. Formation factors are often available from measurements on cores or from electric logs, and many attempts have been made to correlate formation factors and porosities of geological formations. Whenever a successful correlation is found, the engineer working with electrical logs has a useful tool for the determination of porsities of pay section?. One of the more successful formulae applicable to these correlations is the familiar equation empirically obtained by Archie.&apos; which F is the formation factor. $ is the porosity, and rn is an exponent called the cementation factor. When the for- mula applies, the cementation factor usually is found to be between 1.3 and 2.2. The values for formation factors experimentally obtained are often higher than simple pore geometry would lead one to expect. In an effort to account for such high values certain formulae have been derived based on a so-called "tortuosity concept." In deriving these formulae a synthetic porous body is usually assumed in which the solid material is an electrical non-conductor. and in which the pore system consists of three sets of fluid-filled tubes of uniform diameter connecting opposite faces of the body which, for convenience, is considered to be cubical in shape. The three sets of tubes account for the whole of the effective porosity of the body, and usually, it is specified that they do not interconnect. By considering that the pore tubes are not straight but tortuous, their resistance to the flow of electric currents can be made as high as needed to explain high formation factors. Such an explanation has some basis in fact, but it appears that the tortuosity concept is often incorrectly applied when other factors are largely responsible for observed high resistivities. Recently, Wyllie and Spangler have recognized that tortuosity as calculated by conventional formulae has little if any physical significance.&apos; RESISTIVITY AND THE CONSTRICTION CONCEPT Any explanation of high formation factors which depends solely on tortuosity of uniform pore paths necessarily ignores the effect that variations in the cross-sectional area of the conducting paths have on the resistivity of a body. Although, as previously pointed out, the calculation of such paths for an actual body is impossible, it will he shown that a synthetic pore network can be devised which will yield to analysis, and lead to results in agreement with the experimental data represented by Equation (1). The porous body to be considered is assumed to be homogeneous and isotropic or, for present purposes, identical in its characteristics in the three directions parallel to its coordinate axes. It will he assumed to be built of identical unit cubes, each of which contains a single pore network connecting all faces of the unit cube. A unit of such a pore network is shown

Jan 1, 1952

By A. Styka, G. Fischer, S. Tour

Described herein are the results obtained during research work involving coating titanium alloys with molybdenum by vapor-deposition methods. Results show that the method can be used successfully to deposit hard adherent wear-resistant coating of methodmetallic molybdenum on titanium or titanium alloys without changing the microstructure of the titanium base. PRODUCTION and use of titanium and its alloys have increased tremendously in the past few years. The physical, mechanical, and chemical properties of this engineering metal have caused considerable enthusiasm among metallurgists and engineers. However, as with all materials, there are some drawbacks. For example, titanium is susceptible to seizing and galling on wearing surfaces. In order to produce a good wear-resistant surface, many investigations have been conducted evaluating oxidizing, carburizing, nitriding, carbonitriding, sili-conizing, and chromizing of titanium. All of these processes require high temperatures for rather extensive periods of time. It has been possible to produce hard surfaces on titanium and its alloys by a number of these processes at the expense of a deterioration of the physical properties of the base material. A practical solution to the problem of providing titanium and titanium alloy parts with a satisfactory wear-resistant nongalling surface must be one that does not involve excessive temperatures for long periods of time. Sam Tour & Co. Inc. has completed a research and development contract for the United States Army Ordnance Corps on vapor deposition of molybdenum on titanium and titanium alloys. On the basis of results obtained from the research program, titanium alloys can be coated successfully with molybdenum to provide a hard wear-resistant surface without harm to their base mechanical properties. The remainder of this article is a description of the techniques used to apply the coating and the results obtained from wear tests on molybdenum-coated titanium. Theory Basically, the technique used was the application of molybdenum by a vapor-deposition method, thermal decomposition of molybdenum hexacarbonyl [Mo(CO)] with hydrogen as the carrier gas. The selection of this method was based chiefly on the following considerations: 1—low plating temperature which would minimize excessive grain growth, 2— low decomposition temperature of the carbonyl, 3— possibilities of controlling the hardness of the plate by adjusting the carbon content using the plating temperature and pressure as the primary variables, 4—use of high vacuum, thereby avoiding unnecessary oxidation and other complex reactions with the atmosphere. Free energy data1 show the strong tendency for titanium to combine with O2 N2 or carbon from normal temperatures to temperatures above its melting point. To maintain the titanium in a film free condition, the use of as high a vacuum as possible is indicated. The literature&apos; indicates that the reaction product of hydrogen with titanium is unstable in vacuum at around 400°C. 5—Although it is indicated from the thermodynamic standpoint that there is little possibility of removing carbon from either titanium or molybdenum, the work of Lander and Germer -ndicates that the use of a suitable H,/CO ratio is somewhat effective in minimizing carbon deposition. 6—Availability of molybdenum carbonyl. In the simplest form, the conditions of equilibrium3 in chemical reactions involving decomposition of carbonyl are as follows: Mo (CO) ? Mo + 6CO 2CO * C + CO,. The plating rate is proportional to the rate of evolution of CO from the decomposed carbonyl, i.e., it is proportional to the pressure of the gaseous decomposition products. Carbon released from CO gas is the significant constituent for the variability of the physical properties of the product. High carbon deposition is favored by increasing pressure. Limitations are imposed in the selection of plating temperature and pressure. Excessive temperature re-

Jan 1, 1956

By G. R. Speich, S. A. Kulin

The isothermal formation of martensite at subzero temperatures has been studied in an austenitic stainless steel. The amount of martensite formed isothermally in a given time was found to follow a C-curve behavior with decreasing temperature. Since isothermal rnartensitic transformation occurs at temperatures above the true M. temperature of the olloy, the observed M. temperature is dependent on the cooling rate. It is believed that a general martensite theory must include the basic concepts of the strain embryo theory, and also the important role of thermal fluctuations. UNTIL recently the isothermal component of the martensitic transformation had been considered as a trivial effect in theoretical considerations of this type of transformation. One of the postulates used in defining a martensitic transformation was that the reaction was temperature dependent but not time dependent. Cohen and his associates1&apos;2 were the first to report the isothermal formation of mar-tensite. They obsel-ved the time dependency of the martensite reaction at room temperature in plain carbon steels and certain tool steels. They found that a small amount of additional transformation occurred after the specimen reached the quenching temperature and that the rate of this isothermal transformation decreased rapidly with time. These authors considered this phenomenon to be a "tailing-off" of the main athermal reaction. Kurdjumov and MaksimovaL 5 studied the isothermal formation of martensite at subatmospheric temperatures in steels containing 0.6 pct C-6 pct Mn, 1.6 pct C, and in an iron-base alloy containing 23 pct Ni and 3.4 pct Mn. In each case it was found that both the initial rate and the total amount of isothermal transformation exhibited sharp maxima with decreasing temperature. They stated that it was possible to completely suppress the martensitic transformation in the 0.6 pct C-6 pct Mn steel by drastic quenching in liquid nitrogen. They interpreted their results in terms of a thermally activated process. The maximum in the rate of nucleation vs. temperature curve was assumed to be a result of the temperature dependence of the rate of growth of the martensite plates. It has been demonstrated," however, that martensite plates can form with great rapidity even at temperatures approaching absolute zero. In addition," attempts to confirm the reported suppression of the martensitic transformation by rapid cooling of a 0.6 pct C-6 pct Mn steel have proved unsuccessful. On this basis, and on other theoretical grounds, the validity of some of Kurd-jumov&apos;s results and conclusions is open to serious question. Cohen, Machlin, and Paranjpe&apos; have proposed a theory of martensite formation based on the nucleation of strain embryos and a growth mechanism involving cooperative atomic displacements. According to this theory thermal fluctuations can make a strain embryo supercritical and thereby produce martensite isothermally. Das Gupta and Lement&apos; have investigated the isothermal formation of martensite in a 17 pct Cr-0.7 pct C steel at temperatures below the ambient. They found that partial suppression of the martensitic reaction occurred on quenching into liquid nitrogen. That part of the reaction which can be suppressed is taken to correspond to the isothermal rather than the athermal part of the rnartensitic transformation. The initial rate of isothermal transformation for this steel was found to go through a maximum with decreasing temperature. This is in conformity with the findings of Kurdjumov and Maksimova for the steels used in their investigation. Das Gupta and Lement conclude that isothermal martensite formation occurs by the nucleation of new plates and is always preceded by some athermal transformation. An iron-base alloy containing 14 pct Cr-9 pct Ni was used in this investigation to study further the kinetics of the austenite to martensite transforma-

Jan 1, 1953