Search Documents

By M. W. Legatski, D. L. Katz

The best currently available description of the longitudinal mixing properties of a porous medium is an equation of the form which relates the effective longitudinal dispersion coefficient Dp to the molecular diffusion coefficient Do, the electrical resistivity factor F, the porosity <f> and a Peclet number. If the parameters dpa and m are determined for a porous medium of known porosity and electrical resistivity factor, then a dispersion coefficient may be estimated for a given flow rate and a given gas pair. A new method, featuring on-line gas analysis by thermal conductivity and on-line data reduction by analog computation, was developed and used to determine these mixing parameters for eight naturally occurring sandstones and two dolomite samples. The exponent m of the above equation was found to vary between 1.0 and 1.5. The characteristic length dpa in the above equation was found to vary between 0.25 and 1.9 cm, with an average value of 0.4 cm for sandstones. Measurements were made on two cores in which paraffin wax had been deposited by evaporation from a pentane solution. They indicated that the presence of an immobile phase such as connate water could increase the dispersion coefficients significantly. INTRODUCTION While the petroleum and chemical industries have studied the mixing of miscible liquids flowing in consolidated porous media and of miscible gases flowing in unconsolidated porous media, relatively little data have been presented to describe the mixing of gases flowing through consolidated porous media. Such data are of particular interest to the gas storage industry. For instance, the U. S. Bureau of Mines is storing large quantities of a rich helium-nitrogen gas in contact with a natural gas in a dolomite reservoir. Since the rich gas occupies only 15 percent of the total reservoir volume, it is essential that the extent of rich gas-natural gas mixing be predicted and understood as a function of rock properties, pressure and rate of movement. This investigation was concerned only with the determination of longitudinal dispersion coefficients. It is understood that a transverse dispersion coefficient, which characterizes mixing perpendicular to the direction of flow, may be an order of magnitude less than the coefficient characterizing mixing in the direction of bulk flow.5719 It should also be recognized that the use of any dispersion coefficient is in itself a simplification. It is necessary to assume that mixing in a porous medium may be characterized by the equation for flow in a single direction. A number of authors1 l8,19 have pursued the mixing problem, not in terms of the so-called "dispersion model" described by Eq. 1, but in terms of a "mixing cell model". This model supposes that a porous medium is constructed of a large number of small mixing chambers and that the concentration of the diffusing component within each mixing chamber is uniform. Fick&apos;s law (Eq. 1) assumes that there is no gross by-passing of one fluid by another, and that there are not stagnant pockets of gas in the system under consideration as discussed by Coats and Smith.8 These assumptions are not always valid for flow through porous media and it is important to recognize the limitations upon Eq. 1. The most serious limitation upon the assumption of Fick&apos;s law mixing in a porous medium is

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2&apos; The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By O. Cuscoleca

The Austrian plants at Donawitz and Linz were the first to blow steel with high purity oxygen. The paper shows how the process was developed and gives a survey of the results achieved to date. Compared with open hearth steel of equal quality, the obvious advantages of oxygen steel are the low investment and conversion costs. The nitrogen content of oxygen steel is not higher than that of good open hearth steel. Rimmed and killed steel products made by the oxygen process are superior to rimmed and killed steel products made by the best open hearth process. TWO new steel plants using the principle of making steel with high purity oxygen went into operation in Austria, one at Linz (Vereinigte oster-reichische Stahlwerke) in November 1952 and the other at Donawitz (dsterreichisch-Alpine Montan-gesellschaft) in May 1953. An estimated 330,000 metric tons were produced by the two plants in 1953, the first year of operation. In 1954 production by Austrian plants- using the high purity oxygen approach will be raised to 450,000 metric tons. This will be in addition to facilities in Huckingen (Man-nesmann A. G., Düsseldorf, Germany), those planned and under construction at Hamilton, Ontario, Canada (Dominion Foundries and Steel, Ltd.), and elsewhere. It is expected that by 1955 a total capacity of one million tons of high purity oxygen steel will be available. At the close of the last century, because of increasing availability of scrap, open hearth steel production forged ahead at an ever increasing pace. This caused world steel production to rise faster than pig iron production and finally to overtake it. In 1911 65 million tons of steel were produced against 64 million tons of pig iron. World steel production was 209 million tons in 1951, while pig iron output was only 147 million tons. The 1951 breakdown for steel shows 118 million tons made from pig iron, while the balance, 91 million tons or 44 pct of the total tonnage of steel produced, was made from scrap. This increase in crude steel production on a basis of high scrap consumption led to the world market scrap shortage and soaring scrap prices. In the United States and other nations, production of converter steel has fallen far behind that of open hearth steel. The surplus of processing scrap, un-absorbable by converting mills and thus a welcome source for open hearth and electric melting shops in the past, together with regular scrap purchases, no longer can meet requirements of both open hearth and electric steel production in Europe. In addition, recent modification of the basic bessemer process, blowing with oxygenated blast, substantially raised the scrap capacity of these plants. Any further expansion of world steel production will necessitate utilization of self-containing processes in regard to scrap because of the shortage.

Jan 1, 1955

By A. Goldberg, T. E. Tietz, J. E. Dorn

INTRODUCTION THE concept that the flow stress for plastic deformation of metals in the work hardening range is a function of the instantaneous values of the strain, strain rate and test temperature was promulgated by Ludwick1 many years ago. This thought has been more or less a guiding principle throughout the immediate period of development and growth of mechanical metallurgy. It has been tacitly assumed or knowingly applied to many investigations on the plastic behavior of metals. Spurred by the theoretical interest and practical importance of the plastic behavior of metals, many investigators have attempted to determine empirical, semi-empirical, and theoretical equations2-18 relating the flow stress with the strain, strain rate, and temperature. Although the applications of such equations have been extensive, the experimental verification of the existence of a mechanical equation of state is weak. Furthermore, some of the available evidence on plastic flow appears to suggest that no simple functional relation between stress, strain-rate, strain and temperature can exist. The mechanical equation of state demands that [a = a(e, E, T)[I]] Where o = true stress = load/instantaneous area e = true strain = In Instantaneous gauge lengths initial gauge length e = true strain rate T = temperature] This formulation implies that [da] is an exact differential. Therefore the flow stress (o) is a function of the instantaneous values of the strain (e) the strain rate (e) and the temperature (T), independent of the previous mechanical or thermal history. Having reached a certain strain, strain rate, and temperature, by any path whatsoever, a definite and fixed value of the flow stress should be obtained. One check on the validity of the mechanical equation of state is easily obtained. Consider the following three tests on the stress-strain curve at constant temperature: [A. Strain at rate [ei] B. Strain at rate i2 C. Strain at rate [Ei] to [ei] and continue test at i2] A graphical representation of possible results of such tests are shown in Fig I. If, for strains greater than [el], test (C) data coincide exactly with the data from test (B), as shown in Fig Ia, a limited verification of the mechanical equation of state is obtained for the range of strain rates from [ii] to [e2]. But if the data from test (C) differ from those of (B) beyond strain [el] where the strain rate is changed from [e,] to [€2i] the mechanical equation of state is not

Jan 1, 1948

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a&apos; matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a&apos; plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By P. V. Roundy, G. R. Mansfield

Public lands in Florida were first withdrawn from entry by President Taft on July 2, 1910, as a conservation measure because of their possible phosphate content. The reserve thus established was subsequently modified by further withdrawals and by restorations, so that on Jan. 1, 1934, it contained 66,796 acres, of which only a small part had been definitely classified. The reserved land was in scattered parcels, ranging from less than 40 acres to 320 or more, distributed in many counties. For administrative purposes and for final disposal of any of the numerous parcels, mineral classification of the land is legally necessary. In 1934 and 1935 the United States Geological Survey, under two successive grants from the Public Works Administration, prospected some 83 tracts of these lands in Polk County, comprising in all about 3300 acres, and six tracts comprising 240 acres in Citrus and Marion Counties. The tracts in Polk County were all in the so-called land-pebble field and the others in the hard-rock field. The Survey field party was under the direction of P. V. Roundy, from whose unpublished report the material in this paper is largely taken. The foreman of the prospecting crew was J. H. Wingate of Zephyrhills, Fla. The individual tracts were identified through the cooperation of the General Land Office, by transitman Hugh B. Crawford. This prospecting work fitted well the classification adopted for Public Works projects in general: it could not be done on any considerable scale under the Survey&apos;s usual appropriations; it gave employment to unemployed labor; and it may be expected ultimately to repay the Government in royalties more than the cost of the exploration. Commercial, Prospecting Methods Commercial methods of prospeeting for phosphate in Florida have been briefly described by Mansfield.&apos; In the hard-rock field, where the floor of the phosphate deposit is extremely irregular, it is customary to drill a.:

Jan 1, 1938

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line&apos;&apos; and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By Rollin E. Hook, Attwell M. Adair

The yield and fracture behavior of recrystallized chromiztm have been studied in order to gain an understanding of the recrystallization embrittlement-rheotropic recovery phenomenon. The duc tile-brittle tensile transition temperature of recrystallized chromium was found to vary from 225 ° to -80°C as the ratio of specimen diameter/mean planar grain size decreased. The applicability of this observation to other bcc metals is briefly discussed. Brittle fracture in recrystallized chromium was found to be initiated predominately from intercrystalline rupture nuclei. Single crystals exhibit a high degree of ductility at 23 "C. The experimental data indicate that grain boundaries play a significant part in the yield and fracture behavim. Pres training significantly reduces the transition temperature, and high temperature aging does not result in re-embrittle-ment until complete recovery or re crystallization occurs. SEVERAL theories have been used to explain the recrystallization embrittlement-rheotropic recovery phenomenon in chromium. Wain, Henderson, and ohnstone&apos; propose a Cottrell dislocation locking mechanism due to nitrogen, and Weaver and Gross and weaver 3 propose a strain-induced precipitation mechanism involving a chromium nitride precipitate. The researches of many investigators seem to leave little doubt that brittleness in chromium is promoted by interstitial impurities. Smith and seybolt4 have shown that the ductile-brittle transition temperature is lowered as the interstitial content is reduced. weaver3 provides evidence for a 150°C reduction in the tensile transition temperature as the nitrogen content is reduced from 20 to 5 ppm. Maykuth and affee&apos; have suggested that the amount and orientation of grain boundary impurities may be responsible for the brittle nature of recrystallized chromium. This suggestion was based on their findings that wrought iodide chromium possessing a fiberous grain structure is ductile in tension at room temperature while a recrystallized grain structure is completely brittle. Previous investigations have not studied this phenomenon sufficiently to determine its cause. Perhaps this has been largely due to previous experimental findings that brittle fracture observed in chromium has been almost entirely transgranular.&apos; In addition McNeil and imb,&apos; who investigated coarse-grained as-cast chromium, describe the point of initiation of fracture as cleavage, close to the (100) plane, near or at grain bound-daries, or at included particles or voids. However, Hook, Adair, and ipsitt found that fracture in coarse-grained recrystallized chromium is initiated by intergranular rupture and then propagates nearly entirely by cleavage. This result, together with their finding that room temperature ductility in bending is observed for single crystals and coarse-grained polycrystalline specimens for which the number of grains through the specimen diameter is small, suggests that grain boundaries may play an important role in the brittle behavior of chromium. The recrystallization embrittlement problem can be resolved into two questions. These are, whether the controlling mechanism is predominately one of crack initiation or crack propagation, and whether brittle fracture is initiated predominately by slip or twin induced intergranular rupture or by cleavage. The following research was designed to study the role of grain boundaries on the brittle fracture of chromium in an effort to resolve these questions. EXPERIMENTAL PROCEDURES, RESULTS, AND DISCUSSION General Procedure. All tensile specimens (except 0.04 in. diam wires) were prepared from 1/4 in. diam swaged rod fabricated from one ingot. Details of fabrication are given elewhere. The results of impurity analysis for the swaged rod and for the

Jan 1, 1963

By T. G. Lovering

Nonparametric statistical tests have practical application to many geological problems because, unlike the standard statistical tests, they do not require assumptions regarding the form of the population frequency distribution. Many of them do not even require that the variable be susceptible to numerical measurement. These tests are useful either 1) for geological data representing population distributions of unknown form, or otherwise not meeting the requirements for standard parametric tests; or 2) for sample attributes that cannot be measured but only ranked in order of relative magnitude. The application of two such tests will be illustrated. The Kolmogorov-Smimov test will be used to test for significant differences in copper distribution in samples of two rock types; the Spearman rank-correlation method will be used to determine whether there is a significant association between intensity of rock alteration and copper content of the rock. Nonparametric tests are, in general, quicker and easier to perform than the corresponding parametric tests, and they may be applied to a greater variety of data. They are not as powerful as the standard tests if used on data to which the latter are applicable, and computer programs utilizing them are not generally available. The use of standard or parametric statistical procedures for the interpretation of measured geological data is familiar to most mining engineers and explora- tion geologists. The computation of product moment correlation coefficients on sample assays for more-than one component is already standard procedure in some company operations, as is the use of Student&apos;s F test and Snedecor&apos;s F test for the comparison of means and variances of sample groups. The application of these three tests is limited by the prerequisites that the samples must be random, independent representatives of normally distributed populations and that the variables involved must be measurable. If such tests are applied to data which fall short of fulfilling these prerequisites, then the probability level attributed to the computed statistic is invalid and the conclusions based thereon may be erroneous. A number of nonparametric, or distribution free, statistical tests have been developed for use with data which are not amenable to standard parametric procedures. These tests have been widely used in the behavioral sciences such as psychology and sociology for some time, but their application to geologic problems is relatively new. Nonparametric tests may be grouped into two main categories: those which test for significant differences in a single variable by comparing either sample values with a standard value or representative values between two or more groups of samples; and those which test for significant association between pairs of variables in a single group of samples. The versatile chi square test, the Kolmogorov-Smirnov one and two sample tests, the Wilcox matched pairs signed ranks test, the median test, the Mann-Whitney U test and the Cochran Q test are examples of nonparametric tests with demonstrated or potential geological applications that belong in the first category. The contingency coefficient, Spearman rank correlation coefficient, Kendall rank correlation coefficient and the

Jan 1, 1963

By J. K. Kerver, J. S. Osoba, J. G. Richardson, P. M. Blair, J. A. Hafford

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

A Page Adam. H. F. and Ruggles! G. H., Results with Xanthate at Inspiration............. 337 Adnic proertiea of....................... 474 Africa; Gold Coast, manganese...........abs.474 191 mining districts......................... 254 Aid, H., biography........................ 154 Air compressors. In flotation................ 45 Air-gas lift: gae-oil ratios relation of......abs. 475 Gulf Coast. mechanical installations... .abs. 475 Seminole field........................abs. 476 Air-sand process. cleaning coal............abs. 89 Alabema, Birmingham district. drainage. . abs. 86 " Alclad." aluminum alloy................. 395 Alexander. W. Homer. biomaphy .......... 37 Allen. Andrews. Preparing Coal after Mechanical Loaders......:....T................. 181 Allison. F. H., Comparison of the Effect of Nickel and Cobalt in Steel.............aha. 151 Alloys: See Metals named. Aluminum: heat treatment...............abs. 444 machining...........................abs. 443 Norway............................... *465 Aluminum alloys: " Alclad "................ 395 application of........................abs. 443 deformation..........................abs. 150 Aluminum Bronze Manufacturers Institute. organized.............................. 188 "Alumnum. The Metal and Its Alloys." B.R. 42 Aluminum-iron-silicon alloys, equilibrium relations.............................aba. 444 Aluminum-manganese alloys, equilibrium relations in..........................aba. 87 Aluminum-silicon alloys. heat treatment. .abs. 398 American Association of Petroleum Geologists. annual meeting................... 81 American engineers. war memorial.......... 499 American Institute of Mining and Metallurgical Engineers: Committees: Douglas. James, medal...... 324 Geophysical Prospecting............. E. 204 Mining Medal........................ 324 Nominating: Election................. 235 report............................. 479 Constitution. votes for.................E. 494 Constitution and By-laws. draft of....... 374 Directors: Minutes of meeting.....110. 235. 323 publications.......................... 523 Directors adopt badge................... 324 Dues. increasing........................ 111 Dues are Due.......................... 236 Institute of Metals Division: annual lecture............................ 187 data sheets.......................... 187 Detroit meeting, (September). . .307. 353, 440 lecturer C. H. Desch................. 15 Local Section Committee. members..... 187 New York meeting (February)......... 115 Research Committee.................. 187 research problems..................... 6 Local Sections: Arizona............................. 365 Boston, meetings................40, 197. 486 Page American Institute of Mining and Metallurgical Engineers—Continued Chicago, meetings...40, 94, 156, 196,240,417 Chicago and St. Louis, joint meeting, Danville....................... 486, 527 Colorado, annual meeting.............. 285 Columbia, meetings 39, 93, 156, 196, 238, 286, 327, 365, 486, 527 El Paso, organized.................... 238 Fort Worth, organization meeting...... 485 Joplin-Miami Zinc, meeting.......... 286 Lehigh Valley: annual meeting......... 197 meetings...................... 239, 527 Los Angeles, meeting.................. 285 Mid-Continent, meeting............... 156 Minnesota, annual meeting............ 326 Montana, meeting.................... 40 New York, meetings................240, 284 North Pacific: meetings.... 39, 157, 197, 527 Fieldner, A. C, speaker............. 486 resolution.......................... 439 Oregon, officers....................... 196 Pittsburgh: meetings........... 156, 327, 526 mine transportation conference....... 485 St. Louis and Chicago, joint meeting, Danville........................... 486 San Francisco, meetings............... 92, 197, 239, 285, 439, 486, 527 Southern California, meetings 40, 157,197,283 Upper Peninsula, meeting.............. 486 Utah, meetings..........40, 93, 156, 239, 365 Washington, D. C, meetings 40, 93, 365, 528 Medals: Douglas, James................34, *84 Fritz, John, award, 1928.............. 480 Johnson, J. E., awarded T. L. Joseph... 83 Saunders, William Lawrence........... 34 meetings: Cleveland, April, 1927.......166, 207 Detroit, Sept., 1927............307, 353, 440 Fort Worth, Oct., 1927.........307, 353, 471 • future............................. E. 102 Knoxville, Nov., 1927.............. 480, 500 New York, Feb., 1927, announcements, programs, etc.................33, 50, *106 Salt Lake City, Aug...............306, *422 Members and jobs...................... 477 Membership, benefits.................8, E. 2 Officers and directors.................... *122 Open-hearth Conference................. 282 Petroleum Division: activities............ 186 annual meeting...................... . Fort Worth meeting............307. 353 471 luncheon............................ 91 New York Petroleum Club, officers..... 110 nominations........................23. 519 officers.............................. 117 President&apos;s trip. May.................281. 398 Publications: Directors discuss............ 523 Institute of Metals Division Volume... . 178 Petroleum Volume.................... 192 Technical Publications...........E. 294 323 Transactions. Vol. LXXIV. LXXV....00. 524 Review of the year.........:........... ...E. 104 Stockholders. report to..............E. 49

Jan 1, 1927

By E. W. Newman

DURING 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mined during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River, and Absarokee, on the Stillwater River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specifications as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. HISTORY OF DEPOSITS The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the first optical calcite produced from Montana came from the Cartwright deposit near Greycliff,1 but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by A. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the Montana and California deposits. This com-

Jan 1, 1945

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. F. Perkins

CORROSION as an economic problem is growing rapidly in importance not only because it entails a replacement of corroded parts, but because it interrupts operation and causes hazards of damage and injury through failures of corroded equipment. Nearly all industries are interested in this subject. This paper, although concerned chiefly with corrosion in a complete refinery on the sea coast, discusses many of the various forms of chemical decomposition, most of which are found universally. The petroleum refining industry, in the writer&apos;s opinion, is seriously afflicted by the presence of sulfur in nearly all crude oils. The complete removal of sulfur from the crude as it enters the plant would cause such a relief from corrosion that this problem for research would seem to demand active attention. Next to sulfur the most troublesome corrosive agent is the saltmagnesium chloride, found in the water associated with crude oil, the last traces of which are so difficult to remove. This is much less serious, however, than the sulfur. Refinery corrosion can be tabulated as follows: Causes of Corrosion and Places of Attack in a Refinery CORROSIVE ELEMENTS MATERIAL ATTACKED Air: Pipe lines Moisture Tanks COQ Electric fixtures Sulfur gases Still towers Chlorine Condenser boxes Other acid-forming gases Ladders and stairs Smoke stacks Steel buildings All exposed metal Water: Alkali Fire lines and hydrants Acids Cooling water lines Air Condensers and coolers Other dissolved gases Boiler tubes Steam Steam pipes and valves Turbines Oil Sulfur compounds Tanks, pipes, valves, stills, towers MgCl2-Hydrochloric acid Condensers Air contamination

Jan 12, 1926

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By A. U. Seybolt, D. H. Haman

The rate of oxidation of the lowest nitride of chromium, Cr2N, was measured to be equal to the rate of oxidation of chromium metal. It was found that, while the presence of Cr2N in chromium does not affect the oxidation mechanism, a long exposure at high temperature affects the morphology of Cr2N in chromium, causing a massive internal nitriding along chromium pain boundaries. Marker expen&apos; -ments showed that the rate of oxidation of Cr2N layers on chromium is determined by the rate of chromium diffusion through Cr,03. The rate of formation of Cr2N is determined by diffusion rate of nitrogen through Cr2N. This rate at 1000°C is around thirty times faster than the rate of oxiahtion. Evidence is presented which suggests that nitrogen from the air reaches the chromium through the Cr2O9 by migration through pores or cracks rather than by a diffusive process. IT has long been recognized that, when chromium or alloys containing substantial amounts of chromium are oxidized in air, some chromium nitride (Cr2N) is formed under the oxide scale. Although the presence of this nitride layer has often been described, there appears to have been no systematic study of the role played by the nitride during the oxidation process. Indeed, there have been conflicting re-ports&apos;92 on the kinetics of oxidation of chromium and chromium alloys in air and in oxygen. However, it is now well-established&apos;-5 that the rate-controlling process during the parabolic oxidation of chromium to Cr2O3 is chromium-ion diffusion through Cr2O3. Because of the importance of chromium-containing alloys as oxidation-resistant materials, it seemed desirable to investigate the behavior of chromium during oxidation with and without the presence of chromium nitride. Since a semicontinuous Cr2N layer forms relatively early during the oxidation of chromium in the air, chromium atoms must either pass out of or through the Cr2N layer to become incorporated in the growing Cr2O3 scale. Therefore, it seemed desirable to examine the oxidation behavior of the pure nitride. MATERIALS AND EXPERIMENTAL PROCEDURE The chromium used in this investigation consisted of slices of an ingot made from "five-nine" iodide chromium which had been argon-atmosphere melted in a Y2O 3-stabilized ZrO2 crucible in an induction furnace. The only impurity of any significance was 625 ppm of 0, which was usually reduced to a microscopically invisible amount by hydrogen annealing at 1400°C. However, one sample of chromium was used with the as-cast oxygen level as explained below. The samples were used after abrading through 600 Sic paper and then washing in toluene and alcohol. Both nitriding and oxidation experiments were performed in a vertical tube furnace connected to a glass vacuum system. &apos;This system was equipped with pressure measuring instruments for the range of 10 p to 1 atm, and a cartesian-diver pressure-control device was used in conjunction with a needle valve to allow control of pressure in the range of about 10 to 760 mm. The nitrogen or hydrogen gas was purified by passing through hot copper chips at 600°C, anhydrous calcium sulfate (Drierite), and liquid nitrogen. Oxygen gas was dried through the Drierite column and a dry-ice trap (-78°C). Changes in specimen weight were followed by a Pyrex helix used in conjunction with a cathetometer which could reproducibly be read to +0.001 cm, yielding an accuracy of about +0.2 mg. The spring was maintained in the cool upper part of the furnace tube where the temperature did not rise above about 35°C. The nitride in equilibrium with metallic chro-

Jan 1, 1964

By A. Gittens

In two recent papers stevens13,14 has compared the methods used by various investigators to calculate the contribution of grain boundary sliding to the total creep strain. In previous work Gittins15 has shown that the strain due to grain boundary sliding Egb may be estimated from the lateral, d, and vertical, v, displacements of a longitudinal marker line as it crosses a grain boundary. He obtained the formula, where nL is the number of grains per unit length measured on the specimens before creep, and \p and ?2 are, respectively, the angle between the grain boundary and the stress axis in the plane of the surface and normal to the surface (see Ref. 13, Fig. 1). The subscript L indicates that observations are made in a longitudinal direction parallel to the stress axis. It was generally found more convenient to measure the grain size of a specimen before creep; this was necessary to characterize the specimen. Stevens13,14 however prefers to define Egb in terms of NL, the number of grains per unit length after creep. Since nL - NL(l + €1) where cr is the total strain, Eq. 1 11 becomes The quantities d and ?, can be determined directly from the marker lines, while v and ?2 are found by sectioning normal to the surface. In the interior when symmetry considerations suggest that v = d and ?1 - ?2 the strain due to grain boundary sliding may be estimated from a suitable internal longitudinal marker line by the equation To determine cgb at the surface using either Eqs. |1| or [2] requires a large number of observations, particularly if many estimates of cgb are required, and also it is impossible to determine the variation of cgh with creep strain on the same specimen because the specimen must be sectioned to determine ?2. Gittins15 found that for a number of materials the sliding vectors d and v were related to each other so that provided one was measured the other could be estimated. Also during creep, grain boundaries tend to migrate to meet the surface at angles close to 90 deg,16 so that the term nL(v/tan?2)L was comparatively small when 4,- 90 deg. By determining the frequency distributions of ?2 on control specimens this term can be estimated without sectioning the creep specimen. In this way an empirical equation based on Eqs. |1| and |2| enables cgb to be determined with reasonable accuracy with fewer observations of the angles and sliding components. For B brass, the relationship between the sliding vectors indicated that ceb = 0.85nLVL . In Table I of Stevens paper this equation is stated to be incorrectly derived. However it should be pointed out that this is an empirical equation derived from Eq. |1|, based on a knowledge of the relationship between d and v and on the frequency distributions of ?1 and ?2 for a particular material under given experimental conditions. It was used only when these relationships were known, to reduce the number of observations required to estimate cb. Therefore the comment "derivation incorrect does not apply. Gittins did in fact make use of Eqs. |1| and 131. Author&apos;s Reply I must apologize to Dr. Gittins for the inadvertent misrepresentation of his work. Other slight errors in Table I have been pointed out to me. Langdon (No. 12 Table I), Gifkins (No. 7, Table I), and possibly other workers did not measure the number of boundaries per unit length after creep (A&apos;) but the corresponding quantity bejove creep (n). As Dr. Gittins points out, a completely analogous set of equations to those given in the paper can be derived by the same method: using the number of boundaries per unit length before instead of after creep. The basic equations corresponding to Eqs. [2] and 171 of the paper, from which all the others can be derived, are

Jan 1, 1968

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.&apos; As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972