Search Documents

By Charles S. Robinson

Abstract-The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson B Associates Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentay rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease inflow (or pressure) is exponential. By measuring the change inflow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 8, 1978

By L. R. Blair

Many hydrated silicates have been synthesized and sold for commercial use. However, this paper discusses only hydrated calcium silicates and, to a lesser extent, hydrated magnesium silicates. Synthetic calcium silicates were first formed by man when he found that mixtures of silica or silicates and lime in water set up to form cements. The material which was responsible for the cementing properties was calcium silicate hydrate, although this fact was not recognized until early in this century. In the early 19001s, synthetic calcium silicates, reinforced with fibers and formed simply by reacting calcium hydroxide and silica in water with fiber at atmospheric or under low pressure autoclave conditions, found increased use in thermal insulations and in building products. These insulations were found to have a low thermal conductivity and would withstand temperatures up to 650°C. This, combined with their very low densities (from 8 to 50 Ib per cu ft) and fairly high strength, also made them suitable for use as building products. Following the disastrous Morro Castle fire of the 1930Js, calcium silicate board products were used as partitioning material in all shipboard construction in the U.S. As autoclaving techniques were improved and developed, it was: learned that under hydrothermal conditions new and useful calcium silicates which could be used under more extreme temperatures (up to 980' C) could be prepared. These had high surface areas and other unique properties which suited them for use as fillers, pesticide carriers, low temperature insulating materials, and adsorbents for the removal of fatty acids from various solutions. Hydrated magnesium silicates have not been studied as extensively as the calcium compounds. Their first important use was in the filtration of dry cleaning solutions for the removal of fatty acids. With the introduction of detergents, it was found that these products lost their advantage because of their high affinity for the detergent chemicals. However, in recent years these chemicals are finding increasing use as decolorizing agents for fats and anti-caking agents for resins. Some materials with very high surface are finding new use as adsorbents. CALCIUM SILICATE HYDRATE COMPOUNDS AND THElR CONDITIONS OF FORMATION Within the past ten years much has been done in the field of calcium silicate hydrate chemistry. As a result of this work it has been found that at least 25 different forms of calcium silicate hydrate can either be formed synthetically or found as naturally occurring materials. The stability and composition relationships among these 25 compounds present a very complicated picture, and many of these very closely resemble other forms and are difficult to dis-

Jan 1, 1962

By E. M. Cox, T. Rosenqvist

IN a recent investigation, carried out at the Institute for the Study of Metals, the affinity of sul-phur for iron, copper, and manganese was studied over the temperature range 700" to 1300°C.' It was found that copper exhibits a rather high affinity for sulphur, especially at higher temperatures; and attention was called to the possibility that copper when present together with sulphur in liquid steel would tend to lower the chemical activity of sulphur and thus interfere with the desulphurization process. It was clear, however, that the data for the equilibrium between pure copper and pure copper sulphide (Cu2S) could not give any quantitative information about the effect of copper when dissolved in liquid steel. The present work is concerned with the activity of sulphur in the diluted range of the binary iron-sulphur system, and with the influence of small amounts of copper on this sulphur activity. This investigation is in principle based on the same method previously described for the binary metal-sulphur studies;1,2 namely, reaction with hydrogen to form hydrogen sulphide. The equilibrium ratio PH2s/Ph2 in the equilibrium gas mixture is, for a given temperature, directly proportional to the sulphur activity. The activity of sulphur in liquid iron has previously been studied by Chipman and Ta Li,3 White and Skelly,4 and recently by Sherman, Elvander, and Chipman.5 Morris and Williams6 have studied the effect of added silicon, and Kitchener, Bockris and Liberman,7 and recently Morris and Buehl,8 the effect of added carbon on the sulphur activity. In present day steelmaking processes the steel bath contains between 0.01 and 0.1 pct sulphur, and the copper content may be as high as 0.5 pct. The equi-librium gas ratio (H2S/H2) would, for such a low-sulphur content, be too low to be measured with the experimental technique we use. It has been shown by previous investigators that the H2S/H2 ratio is closely proportional to the sulphur content up to about 1 pct sulphur. The sulphur activity at very low-sulphur content can therefore be calculated by linear interpolation between 0 and 1 pct sulphur. In order to show the general trend with increasing sulphur content, the present work has been carried out to about 3.5 pct sulphur. As the effect of copper was assumed to be more a function of the Cu/S ratio than of the absolute copper content, the runs with copper were made for certain constant values for this ratio.

Jan 1, 1951

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.' In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962

By W. N. Best

Crude oil attracted attention because of its excellence as a fuel for openhearth furnaoes; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hotair furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This mcans a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity BaumB. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230". F., Mexican crude oil at from 175" to 210" F., and Beaumont, Texas, oil at 142" F. Fuel oil vaporizes at 130" F. Scientific Installation Essential The burning of oil is an art based on science, and the "rule of thumb" should never be employed, especially in heating heavy crude oil. Thermometers should be used on both suction and supply pipes so that the fireman or smith will at all times know the temperature of the fuel. The indicators on such thermometers should be large enough to be readily seen by the operator, night or day. It is necessary to have an unvarying pressure of steam or air through the burner, to atomize the fuel. Also, the air used to support combustion should be delivered through a nozzle under the burner at a constant pressure. The oil pressure must not fluctuate; under no eircumstances should it vary more than 1 1b. The oil pump, which should be brass-lined, with the aid of the pulsometer and superheater, will insure a constant

Jan 1, 1916

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,'. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955

By C. B. Smith, A. G. Guy

The power and convenience of tensor analysis are employed in deriving the equations that describe three-dimensional diffusion in an n-component system plus vacancies. A "Kirkendall coordinate system, '' defined in principle by Kirkendall markers, is used in defining the intrinsic diffusion coefficients that are of primary interest. The defining equations are then transformed to local cartesian coordinates and to fixed cartesian coordinates, the latter being convenient for experimental measurements. Finally, it is shown how the intrinsic diffusion coefficients can be calculated from the experimentally determined quantities. It is generally recognized that any treatment of the essential diffusion phenomena in metallic systems—the jumping of atoms from one lattice position to another—must be based on movement of the atoms past Kirkendall interfaces.' A logical extension of this idea is the proposal that, fundamentally, diffusion must be described mathematically in terms of "Kirkendall coordinates." The basic equations thus obtained may then be transformed into other coordinate systems, when such transformation leads to simplification of either the experimental or mathematical treatment of diffusion data. Tensor analysis is clearly the appropriate mathematical tool for this purpose, since it provides methods both for determining general equations that are valid for all coordinate systems and for conveniently transforming the equations from one coordinate system to another system related to the first in some known fashion. For the present purpose three coordinate systems are used, and it is convenient to begin with a description of the relations among these three systems. FICK LAW FOR KIRKENDALL COORDINATES The reference coordinate system, and the one that is useful for most experimental measurements, is a cartesian coordinate system, xi (i = 1, 2, 3), fixed with respect to some point in the specimen, such as an end of the alloy bar undergoing diffusion. A second set of coordinates, the Kirkendall coordinate system, is one that in principle can be described by the location of inert markers (Kirkendall interfaces). A convenient mathematical relation between Kirkendall coordinates, x'i, and the reference cartesian coordinates, ii, is obtained by specifying that the Kirkendall coordinate system coincide with the cartesian system at time, t = 0. After diffusion has occurred for some time, t = t, the Kirkendall coordinate system will differ from the reference system in the manner shown schematically for the one-dimensional case in Fig. 1. The third coordinate system is Darken's1 local cartesian-coordinate system, xi, which is identical with ii in orientation and units, but which moves with the point under consideration in the Kirkendall coordinate system. Even though most diffusion problems are essentially one-dimensional, there is an advantage in first carrying out the analysis of the three-dimensional problem to gain a clearer insight into the assumptions that are made in the usual one-dimen-

Jan 1, 1962

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

During the past year the Committee on Coal and Coke has been collecting data concerning various phases of the bituminous industry about which considerable misinformation has been circulated even, in some cases, through the coal trade papers. The data here presented have been compiled by various members, from the most authentic sources available and, where possible, cover the period 1913-1924. They will enable comparisons to be made within the industry, and of this and other industries, and will explain some of the differences between conditions existing now and in the prewar period. Capacity and Over-development The capacity of bituminous mines is frequently stated at figures ranging between 800,000,000 to 1,400,000,000 tons per year. Table 1 shows statistics for the industry, mainly from U. S. Geological Survey sources but partly from U. S. Coal Commission reports. Column 3 gives the mine capacity with equipment and labor as of given date, as estimated from the data published by the U. S. Geological Survey. This is calculated for each State by obtaining the total man days worked as reported by the operators (multiplying average men employed by total days worked at each mine) and dividing this figure into the total production, getting the production per man day; this figure times number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method—one that the total number of men employed is used, instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. The first objection is answered by the fact that the same number of men is used in estimating capacity as is used in actual production, and while this number is always from 12 to 20 per cent. more than are actually working, this condition exists at all times, although it is worse at times of maximum output. Few coal men will agree with the conclusion that the use of 308 days is correct, as it is practically impossible to keep any mine working full time at the same daily rate of production as when it is working part time, and the opinion is

Jan 1, 1927

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

R. C. Canby, Wallingford, Conn. (communication to the Secretary*). —Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and colre, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata, it might be of interest to refer bricfly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911,I gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcorne after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola-furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable chlorine, due to the imperfect conversion of the subchloride to suboxide, as well as that due to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted with the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These fumes had a peculiarly suffocating effect, SO that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been due to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 1, 1915

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guanacaste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active: (2) the Atlantic low-lands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from o to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By John Birkinbine

Much has been contributed to the Transactions of the Institute concerning the construction and operation of American blast-furnares ; but the following compilation is offered as possibly furnishing additional information upon the general features, dimensions, locations, capacities, etc., of the blast-furnaces of the United States; while, incidentally, the ores upon which they rely are noted in a general way. The paper is presented chiefly as a compilation, and the figures given are selections from most reliable sources, or averages calculated from official statistics, placed for convenient reference, with a view of assisting those who consult the Transactions in determining the present relative merits and importance of various sections of the country. The scope of the paper has been restricted to as few topics as possible, and all the details of special plants, or notable outputs have been ignored. While every effort has been made to give correct figures and data, the changes which are constantly taking place in the iron-producing industry, will, undoubtedly, by the time the paper is in print, develop some errors. It is difficult to determine which of the blast-furnace plants of the country should or should not be considered as upon the active list. A number which have not been in operation for years are still reported as active, some of which will scarcely be put in blast again, and others are handicapped so that they can only operate in times of abnormal profits. It is therefore scarcely probable that there are over 600 blast-furnaces in the United States which can properly be considered as active; but so many considerations affect the various plants, that, it being impossible to determine the exact number, I have relied upon the annual reports presented to the American Iron and Steel Association. Concerning the number of plants which could be stricken from the list, the Secretary of this Association says: "In January last (1885) we enumerated 669 furnaces, which included many stacks which had not been in blast for a very long time, and others which could not be operated except during short periods of exceedingly high prices for pig iron. We have gone over this list very carefully and have eliminated 10 anthracite, 19 bituminous, vol. xiv.—36

Jan 1, 1886

By R. G. Hall

An article on the subject of electrolytic zinc no longer needs to be preceded by an apology. The production of zinc by electrolysis is past the laboratory stage and has become an economic factor of considerable importance in the total production of zinc in the United States. The various methods of procedure to be followed fa the greatest economy of manufacture are fairly well known, consequently a detailed description of any method is no longer necessary or desirable. In this paper I shall endeavor to lay down some of the governing conditions in this industry, the relation of methods to ore deposits, freight rates, and sources of power supply. Power Points Assuming for a moment that, for the present at least, the electrolytic production of zinc will be confined to Those localities having developed water power, a glance at these powers so developed in the United States, with their relation to known zinc orebodies of economic size, will not be without interest. Northwest In the Northwest we have water powers, developed and undeveloped, . in Washington and Montana. These must, of course, bear a close relation to the rapidly growing zinc production of the Coeur d'Alenes and of the Butte districts. In general, the power of the territory in question is relatively low-priced, at least as compared with the cost of developing power from coal, and the near neighborhood of large bodies of more or less complex zinc ores makes these water powers of more than usual interest. The same remarks may be applied equally to the developed water powers of the Canadian side of the line in the Northwest, where we have again commercially available complex ore deposits such as are being exploited today at and near Trail. California One of the large complex ore deposits of the far West is to be found in Shasta County in the immediate neighborhood of the territory of the

Jan 1, 1918

By A. A. Smith, J. S. Smart

NUMEROUS investigations of the effects of the various impurities common to commercial coppers have been published, and the data have found wide use in industry. Naturally, emphasis has been placed on the oxygen-bearing coppers of the tough-pitch variety, but need is now evident for data covering the oxygen-free condition as well. Furthermore, relatively few of the important reactions between oxygen and the various impurities are well understood, and often the data at hand are not applicable to the low concentrations encountered in commercial coppers. This paper presents the changes in conductivity and softening temperature derived from individual additions of the group VIII triad, iron, cobalt and nickel, to high-purity copper, and constitutes a portion of the copper-research program being conducted at the Central Research Laboratory of the American Smelting and Refining Co. The method of preparation of high-purity copper and its alloys in either the oxygen-free or oxygen-bearing form has been described previously.1 The purity of this material, and the methods developed to produce it, provide the means for direct investigation of the very low concentration range in which the various impurities generally exist in commercial coppers. The usual necessity for extrapolation to this range using the results obtained from higher concentrations, and the interfering effects of extraneous impurities, are thus simultaneously circumvented. Since previously published data have adequately presented the effects of higher concentrations of iron, cobalt and nickel, the present investigation has been confined to the composition range 0 to 0.05 per cent. All alloys were initially prepared in the form of oxygen-free continuous cast rod, the weighed alloying additions in suitable form being charged with the pure copper to the continuous casting crucible. The best of the available high-purity alloying materials were used, and spectrographic analyses confirmed the absence of interfering elements from the alloys formed. Each series was compounded in the direction of increasing concentration, starting with pure copper in a new crucible and finishing with the 0.05 per cent alloy. Composition was closely controlled by adding the alloying element in the form of a carefully compounded and analyzed master alloy rendered uniform by continuous casting. The accuracy of this method of synthesis was proved by chemical analysis of the more concentrated alloys, and, accordingly, there is every reason to credit the stated composition of the very dilute alloys in the range where chemical analysis becomes highly uncertain. Oxygen-free samples for measurements of conductivity and softening temperature were obtained by drawing the continuous cast rod to wire of 0.081-in. diameter, employing a number of intermediate anneals to refine the grain structure. The

Jan 1, 1942

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way 'to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951