Search Documents

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young's modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young's modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-' (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young's modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C'. Young's modulus of polycrystalline samples with strong [110] textures and Young's modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young's modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young's modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By Hisaaki Takata, Nobukazu Nanko, Ichiro Izawa

INTRODUCTION Tochibora Mine belonged to Kamioka Mines, which are located in Gifu Prefecture, the cen- tral part of the Japanese main island, has occupied the important position as a main source of silver, lead and zinc for the smelter of Mitsui Mining & Smelting Co., Ltd.. The annual production of crude ore goes up to about 1 mil- lion metric tons with average grades of 20g/t Ag. 0.31% Pb, and 4.18% Zn. For the last 20 years, the mine has struggled with the depressed zinc metal price in yen and the escalation of operating cost, especially la- bour cost. For instance, prices of commodities and labour cost have been raised 8 times and 14 times respectively during this period. On the other hand, total operating cost has been con- trolled to increase 4.5 times. The productivity of the mine has been increased 4 times by means of improvement of individual works and adoption of perfectly mechanized trackless mining system to reform the mining method. Some improvements are presented as follows; Today, drifting is carried out by the tunnelling crew which consists of 9 operators equipped with 5 Mobile-Jumbos, 2 LHD's and a jeep for carrying and loading ex- plosives. In order to get the high utilization of these machines, each crew manages systematically and continuously adjacent 15 faces under the direction of a forceman. As a result, we have accomplished high advance of drift. Furthermore, raising is carried out by a set of the raise-borer in case of long raises like ore- passes and also by the stage blasting method in case of short ones like slot-cuts. Generally speaking, the sublevel stoping method is considered to be one of the best methods for various respects; high productivity, low cost, easy grade control and safety. This method has been introduced in Tochibora Mine since 1950 and is now widely applied to lodes that could not be mined before by this method be- cause of the shapes of them and the conditions of their country rock. Now we are convinced to be nearly accomplished for our method. This report presents some examples of the standard sublevel stoping method and its variations which are practised at the mine. STANDARD SUBLEVEL STOPING Up to 1979 since 1950 when this method was first applied at the mine, 17 million tons of crude ore have been produced by this method, which amounted to 55% of the total production of the mine. During three decades, the productivity has been increased considerably by means of trackless mining system using large-sized machines and etc.. In other words, mining efficiency has been increased from 20 tons/man.shift to 100 tons/man.shift at large stopes. Formerly undercutting was carried out above the drawing drift by jack-legs and small scrapers and then several cone-shaped glory holes were made by stopers between the undercut level and the draw level. But now, a undercut drift is driven in parallel with the haulage drift at the same level of it. And at the undercut drift, drilling upward is carried out by a large-sized machines like the fan drill in order to extract the broken ore directly at the drawing drift connected with the haulage drift. Simplification of the work as well as utilization of large- sized machines enables to get higher productivity. But if the deposit is comparatively wider and the broken ore around the middle part of the deposit cannot be extracted, several drawing drifts are driven to the deposit and in order to minimize dead ore at the final stage of operation, the

Jan 1, 1981

By Charles M. Romanowitz

The motivation for the art of dredging for placer mining can be compared in a slight degree to the spread of civilization which started in the Near East and spread both east and west. Dredging started with the "bag and spoon" dredge in the lowlands of Europe reportedly about 1565, went southeast to New Zealand where designs were developed for a bucket-line mining dredge known as the New Zealand type, and westward to the eastern United States where a dredge was developed and used exclusively for excavating. Then it moved to Montana, where it was first used for mining in 1895. The New Zealand-type dredge was imported into California in 1898 (Fig. 1) and was followed shortly by the Montana design. As today, these early dredges were equipped with continuous bucket- line chains, a treatment plant, and a means of waste disposal mounted on a wooden hull. Both types of dredges are complete mining units: they dig the formation, transport the dug materials, and concentrate the valuable ore. After sizing, the fines containing the ore are passed by gravity to the treatment unit, while the barren materials are discharged overboard. By digging the materials to be treated at the bow and depositing all the waste, at the stern, the dredges automatically advance to new reserves without presenting any transportation problems. The main differences between the two types are in the method of holding the dredge in the digging position and in the disposal of the tailings to the rear. The New Zealand type (Fig. 2) uses the headline system with a bow anchor for holding the dredge in the digging position and long tailing flumes or short stackers off the stern for disposal of the barren materials. The California type (Fig. 3) uses box girder spuds projecting into the ground in a vertical position at the stern of the

Jan 1, 1969

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine-ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between main airways in metal and coal mines, and the methods presented are applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions. Increasing the area of an airway increases the cost for excavation and lining practically proportionately but at the same time affects a very rapid decrease in power requirements. The balancing of these two factors of the expense to give a minimum total yearly operating cost for ventilation is mainly a matter of proper original design of the main airways of the mine, since the large volumes handled through these parts of the system involve large power costs and thus present opportunities for effecting large savings through proper design. Many of the factors

Jan 1, 1932

By W. G. Matteson

The Oklahoma legislature recently passed a bill providing for "the creation of an oil and gas department under the jurisdiction of the Corporation Commission, authorizing the Corporation Commission to appoint a chief oil and gas conservation agent, and conferring exclusive jurisdiction on the Corporation Commission in reference to the conservation of oil and gas, and the inspection of gasoline and oil, the product of crude petroleum, and repealing all acts or parts of acts in conflict therewith and declaring an emergency." Some of the functions of the new bureau include the receiving and filing of all well logs, and the direction and supervision of plugging all abandoned oil and gas wells, under rules prescribed by the Corporation Commission. The two leading petroleum-producing States of the country, Oklahoma and California, have now established oil and gas bureaus with a staff of inspectors to see that the important rules relating to the conservation of oil and gas are thoroughly enforced. The economic significance and the value of well logs in the conservation work has been recognized, and the necessary legal action taken to insure and procure them. William B. Heroy, of the Government Land Classification Board, in a personal communication to the writer, says that the drilling of wells is also regulated by public authority in the Roswell artesian basin in southeastern New Mexico, where a permit must be obtained for the drilling of any well and a certified log of the well recorded with a county official. The method is said to give fairly satisfactory results. In a recent article1 a National instead of a State Bureau was suggested for collecting and filing well logs. In discussing the paper, L. L. Hutchison characterized such a plan as impractical because the average driller or contractor will often juggle or guess at the log and will not keep the record sufficiently close or accurate, making it necessary to maintain a special man at each well for the sole purpose of obtaining

Jan 1, 1918

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By Theodore B. Winkler, John Chipman

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By S. A. Falconer

One of the outstanding achievements in connection with this country's war efforts has been the ability of our mining industry to supply from domestic sources many of the minerals of strategic importance that formerly were obtained principally from abroad. In order to meet the war-born demands for these scarce minerals, it has frequently been necessary to develop special methods for treating ores and waste products hitherto considered too lowgrade to be workable; and to improve the efficiency of older beneficiation processes. Important in this respect have been the recent technological advances in the field of froth flotation of nonsulphide minerals. Because of the refractory nature of many of these domestic ores, and, in many cases, the limited available technical data regarding their treatment, much research work has been necessary. The following examples describe the procedures and reagents used, and the results obtained, in certain laboratory flotation investigations conducted by American Cyanamid Company's engineers at the Cyanamid Ore Dressing Laboratory on ores containing such minerals as scheelite, manganese oxides and carbonate, ilmen-ite, brookite, kyanite, garnet, spodumene, mica, feldspar, celestite, fluorite, chromite, corundum, and cassiterite. In presenting these data, we wish to point out that many of the minerals listed have previously been tested, and their amenability to flotation reported, by other investigators—notably those of the United States Bureau of Mines. In some instances the procedures and reagents used in the treatment of some of the following described ores follow rather well-established lines, and with one or two exceptions, the reagents used were well known. However, many of the ores tested did not respond well to simple conventional procedures and it was necessary to adopt special methods of conditioning and desliming, reversal of the usual order of floatability of some of the minerals, multiple cleaning, etc., in order to secure separations. Except where otherwise noted, all numbered and trade-marked reagents mentioned in this paper are marketed by the American Cyanamid Co. or the American Cyanamid and Chemical Corporation. Tungsten ORes Tungsten minerals, vitally important in the war industries of the United States, rank high in the list of those we formerly had to import in order to supply our needs. Most of our domestic ores of tungsten contain scheelite as the valuable mineral. Today there are in the neighborhood of twelve tungsten operations in this country where flotation is used as the main or accessory form of benefication. It has, of Course, been known for some time that scheelite and other tungsten minerals respond to treatment by flotation.

Jan 1, 1947

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By R. W. Smith, T. J. Smolik

Recent work indicates that fluosilicate ions and or fluosilicate amine complex ions play important roles in fluoride activation of bery and feldspars in cationic flotation systems. In an attempt to further confirm conclusions reached in this earlier work, an infrared and X-ray diffraction study of the action of fluorides in cationic flotation of silicates was undertaken. It should be noted that in recent years considerable use has been made of infrared spectroscopy in studies of surface phenomena,2-4 and these studies have established the excellence of the technique. In the present study infrared spectra were obtained for various products of the reaction of HF and dode-cyclamine hydrochloride with quartz, microcline and beryl. These spectra were compared with one another and spectra of several inorganic and organic substances. In addition to infrared spectra, X-ray diffraction patterns were run on many of the reaction products obtained. A model 137 B Perkin Elmer Infracord double beam spectrophotometer containing sodium chloride optics was used to obtain the spectra. Infrared samples, except for the dodecylamine sample, were prepared by thoroughly mixing the substance to be analyzed with purified KBr in steel vessels on a Wig-L-Bug amalgamator. One-half in. pellets weighing 100 mg were than pressed under vacuum. Details concerning percentage of the substance to be analyzed in the pellets are indicated on the spectra. In all cases except for dodecylamine a KBr pellet was placed in the reference beam of the spectrophotometer to cancel bands due to possible impurities in the KBr. The dodecylamine sample on which an infrared spectrum was obtained was prepared by placing pure dodecylamine between two salt plates. X-ray diffraction patterns were obtained with a Norelco instrument, using a copper target tube, nickel filter and Geiger tube detector. The samples were ground into powders and either placed on glass slides with glue or placed into regular powder sample holders for diffraction studies. Goniometer scanning speed varied from 1°/min to 1/8°/min. EXPERIMENTAL RESULTS AND DISCUSSION Infrared spectra of microcline, beryl and quartz were obtained first and are shown in Fig. 1. These spectra agree reasonably well with previously reported spectra.5,6 The microcline (Fig. 1 a) and beryl (Fig. 1 b) were from good Black Hills crystals. The quartz (Fig. 1 c) was from a large, clear Brazilian crystal. It is not clear whether absorption bands of minerals are due to molecular vibrations, lattice vibrations or both. Fig. 2 shows infrared spectra of dodecylamine (Fig. 2 a) and dodecylamine hydrochloride (Fig. 2 b). The dodecylamine spectrum checks quite closely with that reported in Sadtler.8 Little is known of the spectra of hydrochloride salts of amines,9 and a spectrum of dodecylamine hydrochloride could not be

Jan 1, 1965

By R. T. Webber, R. B. Owen

The vapor phase deposition of molybdenum and tungsten from the hexacar-bonyls has been thoroughly investigated by Lander and Germerl, and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2'3 could be similarly deposited, but did not investigate this metal extensively. Recently, conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. Apparatus and Technique The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T² and T3 containing crystals of the carbonyl. T² is kept in a constant temperature bath (not shown), while T³ is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Se, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by Sb is used to determine the volume included by S4, S6, SB, Slot the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: (I) the specimen temperature, from room temperature to about 1000°C, (2) the carbonyl vapor pressure, from 40 to 220 microns, and (3) the hydrogen flow. In several runs, 0.8 to 1.8 PCt of hydrogen sulfide was introuced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1949

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By G. Sachs, E. J. Ripling, J. J. Lynch

It is general practice to evaluate the strength properties of a particular metal from its stress-strain (s1 — el) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress," (s), and a certain limiting strain, the "ductility" (es), before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (I) the shape of the neck and (2) average values of the stresses and strains over the cross-section at the moment of fracture. However, for the pur. pose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusiom also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locos of failure. In this paper, the effects of straining (at room temperature) by various methods on the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to Our present knowledge, any such prestrainitlg results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain,'' from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1949

By A. W. Schlechten

The proposition is advanced that edutcation specifically for exlractive metallurgy is desirable not because the course content is cmique but rather as a means of indoctrinating the student with a backgrocmd that will give him an interest and pride in the profession. Factors that have caused the decline in enrollment in metallurgical engineering courses emphasizing extractive processes are being overcome. There is a need to distinguish between the sciences of metallurgy and the engineering applications to avoid confusion both in and out of the profession. AS a first step in preparing the 1967 EMD Lecture I searched the literature to determine what my predecessors had done hoping thereby to gain some clues for my own performance. The Transactions of the Metallurgical Society show that the first EMD Lec- turer in 1959 was Dr. W. J. Kroll, known chiefly today for his pioneering work on the production of titanium and zirconium, but equally respected by an earlier generation for his contributions to lead refining. He has been followed by a series of well-known and competent metallurgists all possessing specialized knowledge that has served as a basis for their lectures. The EMD Lectures have in general been a review of the development of a certain aspect of the extractive metallurgical industry or a preview of a particular area of science or technology that has applications in extractive metallurgy. The usual format is to describe developments of the past, summarize the present state of knowledge, and make predictions for the future. There has been great variation in the relative amount of time devoted to these three subdivisions, the past, the present, and the future. For example, Professor Gaudin, the 1961 EMD Lecturer, in speaking of Separation Engineering on the Moon, did not have too many examples of past practice and so had to emphasize the future. It is cheering to observe that all of these authorities were optimistic in their predictions. Despite the fact that four of the previous EMD Lecturers have been educators, Professors Gaudin, Pidgeon, Schuhmann, and Kellogg, none of them discussed the subject of education for extractive metallurgists. I might say parenthetically that lecturers in other divisions, such as B. M. Larsen, J. B. Austin, F. D. Richardson, John Chipman, and R. F. Mehl, have commented with concern on the present state of training for extractive metallurgy. What can you say that is new about extractive metallurgy education? Certainly nothing new can be said about the educational process itself. Professional educators do have new approaches to teaching and learn-

Jan 1, 1968

By Horace V. Winchell

The laws here referred to are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry. Reason Number One The first objection to the continuance of the present law is that it was not planned by its framers and the Congress which passed it to apply to many of the kinds of mineral deposits, nor to the mining conditions, which are controlled by it to-day. In 1866, under the title, "An Act granting the right of way to ditch and canal owners over the public lands, and for other purposes," was surreptitiously smuggled into existence our first mining law (14 Stats. at Large, Chap. 262, p. 251). This law provided that "whenever any person or association of persons claim a vein or lode of quartz or other rock in place, bearing gold, silver, cinnabar or copper, having previously occupied and improved the same according to the local customs or rules of miners in the district where the same is situated," etc., a patent might be granted an certain conditions. This was evidently an Act intended to validate claims already initiated, and to accord Federal recognition to mining locations made in

Jan 1, 1915