Search Documents

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I .03 -I.06 Acid number.................. 6-8 Softening point, mercury method 160º-165ºC Iodine value (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 Purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration ennineeru for Combined Metals Reduction CO., obtained U, S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1948

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By George Frederick Kunz

The manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg.; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a ki1ogram. He also called attention to the fact that while this would depreciate the present diamoiid carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.' The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sévres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3 The general adoption of a uniform standard for dealings in pre-

Jan 1, 1914

By Frederick Laist

While remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the Mac-Dougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide. The acid required for the operation of this plant will be purchased, ad the quantity required is not sufficient to justify the installation of an acid plant. An acid plant will, however, be established in con-

Jan 1, 1914

By L. H. Wolfe, J. O. Thieme

The tensile and shear strengths of frozen soil and the compressive strengths of ice and frozen soil were measured These tests showed that the strength of ice and of frozen soil increased as the temperature was decreased. A method is presented for the measurement of thermal conductivity and specific heat of earth and ice. Using the parameters thermal conductivity, specific heat and density, the thermal diffusivity was calculated. Results of thermal property tests establish water as the major variable contributing to thermal property values. INTRODUCTION During the last few years, a considerable interest has developed in underground storage of cryogenic liquids such as liquid natural gas. Because of its economy and safety, underground storage is being used. Before underground caverns could be seriously considered, however, the strength and thermal characteristics of the soil had to be obtained. Methods are presented herein for measuring tensile, compressive and shear strengths, specific heats and thermal conductivities. The tests were performed on two soils at temperatures from ambient to -195C. Because it is difficult to find data in the literature that pertain to a particular soil, ice was used to evaluate some of the experimental procedures. Some of our ice data are compared to the published values. PHYSICAI, PROPERTIES SOIL SELECTION AND SAMPLE PREPARATIONS The physical and thermal tests were performed on recompacted samples of two typical soils that might be encountered in underground caverns: a gray, fire clay that had been pulverized and mixed with water into a pliable mud; and a brown, sandy silt that was dug from a dry river bank and subsequent1y mixed with tap water. The moisture content of the test specimens was 17 to 22 per cent (based on the wet weight of the soil). This amount of water nearly saturated the silt, but the clay was well below the saturation point. The soils are partially described by the sieve analyses (Fig. 1) which show the particle size distribution of the coarser than 44 micron portion of the soils. The curves also show that approximately 75 per cent of the clay and 20 per cent of the silt are finer than 44 microns. The particle size seems to affect some of the physical properties, and the finer than 44 micron portion is important in the thermal conductivity test. Physical specimens were cut with a bandsaw from frozen blocks of the soil. The specimens were then sanded and kept frozen until after they were tested. They were stored at the approximate test temperature for several hours. Then, to equilibrate the samples to the test temperature, they were stored at the temperature at least an hour before they were tested. TEST EQUIPMENT An Instron, which is a constant speed gear-driven instrument, applied force to the samples and drew stress-strain plots of the test. All of the samples were strained at 0.02 in./min. All of the physical tests were conducted in a temperature cabinet that controlled the temperature to 1C. TENSILE STRENGTH Briquette or "dog-bone" shaped tensile specimens were pulled with suitably shaped jaws. This shape of specimen, which is usually used for tensile tests of concrete, is satisfactory for testing frozen soils except that the samples tend to

Jan 1, 1965

By F. G. Cottrell

About a year and a half ago, at the San Francisco meeting of the American Chemical Society, in connection with the excursions to local smelting-works, I had occasion to show some lantern-slides illustrating the recent commercial development of electrical methods for precipitating the suspended matter from smelter-smoke, the underlying phenomena of which were clearly brought to the attention of the technical public by Sir Oliver Lodge as long ago as 1884. In the .Journal of Industrial and Engineering Chemistry, August, 1911, most of these views were reproduced, together with an account of the work from its beginning up to July, 1911. To-day I wish particularly to show you some of the further developments of the work since that time; but in order to make these clear they will be prefaced by a brief abstract of the article above referred to. The removal of suspended particles, from gases, by the aid of electric discharges is by no means a new idea. As early as 1824 we find it suggested by Hohlfeld ' as a means of suppressing ordinary smoke, and again a quarter of a century later by Guitard.2 These suggestions, which do not seem to have stimulated any practical study of the question, were soon entirely forgotten, and only brought to light again by Sir Oliver Lodge: many years after he himself had independently rediscovered the same phenomena and brought them to public attention4 in a lecture before the Liverpool Section of the So-

Jan 1, 1913

By William F. Cerini, Willis R. Battles, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By R. S. Handy

Does hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Cœur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 11/2-in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgi-cally more economical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 11/4-in., opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in, hand-sorting, then, it must lie in the metallurgical results achieved. Possibly the favor that hand-sorting has found is due to a misconception as to what happens to the clean shipping ore if it is sent to the mill. If a mill makes, say, an 80 per cent. recovery on its feed, the hand-sorting advocate may assume that if the hand-sorted product be sent to the mill, 20 per cent. of the metals contained in it will be lost. This, I believe,

Jan 1, 1920

By Roscoe C. Clark, Henry F. Coffer, J. J. Reynolds

A cement slurry lightweight additive has been adapted in the Conoco laboratories for use in oil well cements. This additive makes possible the use of air to lighten oil well cement slurries. Specifically, the additive consists of small clay bubbles of air having sufficient strength to resist crushing by bottom hole pressures. Clay bubble cement slurry weights can be safely reduced to 10 Ibs/gal. In addition, the clay bubbles tend to act as lost circulation materials and to provide a cement texture which should produce good perforating characteristics. Clay bubble cement is relatively impermeable. INTRODUCTION In many areas in Oklahoma, Texas, Wyoming, and California, difficulties are experienced during casing cementing operations with lost returns caused by the high density of the cement slurries. Wells in these areas are ordinarily drilled with 9 to 11 lbs/gal. drilling mud while neat cement slurries may range in densities from 14.5 to 17 lbs/gal. In these areas, cement slurry weights are at present being successfully reduced to around 12 lbs/gal. (under bottom-hole conditions) by the use of additives in the cement. Since the use of additives will decrease the strength which the cement will develop, the amount of additives which can be used must be based on the minimum cement strength which is acceptable; and thus the maximum slurry weight can be reduced. At present, the minimum tensile strength generally acceptable is 50 lbs/sq in. cured for 24 hours under bottom-hole temperature. This figure is based on laboratory tests1 and on a large number of cement jobs which have been conducted using cement which will not develop more than 50 psi tensile strength in 24 hours under bottom-hole conditions. Two additives are now in use for decreasing cement slurry weights. These are expanded perlite and/or bentonite. The density of both of these materials is greater than that of the cement slurry; however, large quantities of water may be added with these materials without producing a slurry which will settle out of suspension. It is these large quantities of water which contribute to the reduction in the slurry weight. The minimum slurry weight at present obtainable with expanded perlite and/or bentonite is approximately 12 lbs/gal. using a standard Portland cement slurry. In many areas, this weight reduction is insufficient; and returns are still lost during casing cementing operations. In many cases, the pay formation itself is fractured; and a considerable quantity of this cement is lost to the pay zone. It is therefore believed that if cement slurry weights can be reduced to as low as 10 lbs/gal., two advantages will accrue: 1. The lighter densities (10 to 12 lbs/gal.) should mitigate or eliminate lost returns during casing cementing operations. 2. Cement slurries above 12 Ibs/gal. (the present minimum limit ) should develop considerably more strength than is now being obtained. A tensile strength of 100 psi is desirable.' It is the object of this paper to describe a cement slurry having a weight of 10 lbs/gal. and capable of

Jan 1, 1955

By C. W. Stratford

[During the last few years, the necessity for development work has been generally recognized by executives throughout the oil industry, resulting in greatly accelerated progress and the adoption of many noteworthy improvements in refining methods and equipment. Several years ago, the Associated Oil Co. decided to improve distillation methods with the object of reducing refining costs. This extremely interesting work was entrusted to the writer, and W. S. James, now Chief of Research for Studebaker Corpn. of America, was selected as the principal collaborator. The latter contributed much during his two years with the Associated Oil Co., to the development work that has followed. The writer extends to the Associated Oil Co. his appreciation for permission to disclose the details of distilling equipment. In petroleum refining the principal requisites of good economics are the separation of high-priced distillates from those of lower price; maxi-mum yield of any desired distillate; lowest capital investment in refining equipment; lowest cost of operation and maintenance, and the best adaptability and flexibility of the same refinery equipment for handling crudes of widely varying characteristics. The first two items mentioned, separation and yields of distillates are determined by efficiency of fractionating equipment,. Discussion in this paper is chiefly concerned with oil-heating equipment, combustion and furl economy. It has long been well known that velocity plays a very important part in all heat transfer systems. Any betterment in specific transfer. rates in such systems must. always involve velocity. Realizing this fact, IV decided to adopt as a basic principle, the employment of energy to impart velocity required for high transfer rates through a heating diaphragm, and our method of modernizing obsolete shell stills is founded on this principle. Mechanical energy is usually cheap and its rational rspcntliture is returned in the form of greatly increased heat transfer rates, on both oil and gas sides of the sheet. Certainly there is nothing new in this principle, the only novelty being that of our peculiar method of application On the oil side (Fig. I) use is made of a centrifugal pump to jet the oil against the heated sheet thereby creating a high velocity sheet flow over the entire fired area. Such a pump is one of the most efficient machines, so far developed, for moving fluids. 'I'he oil, under pressure impinging

Jan 1, 1928

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts' concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

A LARGE attendance at the annual dinner of the Institute, to be held this year on Tuesday eve-ning of convention week, is already assured. Presentation of the Douglas, Hunt and Saunders medals will attract unusual attention since not only in Blaylock, Mathews and Hoover the Institute will be honoring men who have made notable contributions to the advance-ment of their profession, but as to one of them each person as he passes down the reception line will be won-dering whether in renewing acquaintance with our past-president and present Secretary of Commerce, he is not greeting the next president of the United States. Elsewhere in this issue accounts of the professional careers of these three men appear as also of the two younger men, Charles H. Herty, Jr., and P. H. Royster, who are to receive the Robert W. Hunt and the J. E. Johnson awards. Institute honors go for technical achievement, but the Institute will be proud and happy if the nation should later confirm its own judgment by placing larger responsibilities on one of its members. The medals are to be presented at the annual dinner following the President's reception and preceding the dance. There will be no. other speeches and since the occasion falls on Carnival Night a particularly gay evening is anticipated. The event will be at the Wal-dorf as usual, and members are urged to return prompt-ly the reservation cards sent them by mail. Other entertainment features will include a Smoker, Monday evening at 8.15, held at Mecca Temple and in charge of a new committee with Fred Kay of the Petro-leum Division as chairman. He promises that vocal music will not be allowed to interrupt conversation. Lunch will be served each day on the Fifth Floor of the Engineering Societies Building, and ten special luncheons and dinners have been arranged for particu-lar committees and groups as shown by the detailed program. The Woman's Auxiliary has laid out a gen-erous program including luncheons, teas, a theater party on the night the men folks go to the Smoker, visits to museums and, not the least important, a round of the leading shops. The Excursion Committee is arranging for an excur-sion sure to be of interest. The American Smelting and Refining Co. has opened its great Perth Amboy plant to the Institute, and on Thursday, Feb. 23, a party will be taken to it by bus traveling through the Holland Tunnel en route. Full opportunity will be afforded those interested to see the workings of the ventilation system of that great public work. If a sufficient number indicate interest, arrangements will be made for group excursions to other plants in the vicinity of the city.

Jan 2, 1928

By Benjamin Lustman, Robert F. Mehl

THE study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation-i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from o to 1000-2000 Angstroms-has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difference may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations. 3,4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 EXPERIMENTAL PROCEDURE Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and reproducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900º to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal.

Jan 1, 1941

By Edwin Hopkins

THE year 1923 started a few days after the Venezuelan Oil Concessions, Ltd., discovered a 140,000-bbl. well at. La Rosa and a well of between 2500 and 5000 bbl. at La Paz, on the opposite side of Lake Maracaibo. These nearly simultaneous events changed, overnight, the general aspect of oil affairs in Venezuela. Up to that time, big things had been expected by the companies then in the district, but many major companies had shown little interest in the country. Within a few weeks the Pure Oil. Co. and the Gulf Oil Corpn. entered the field and acquired large properties. The Texas Co. purchased several concessions and the Standard of California, Atlantic Refining Co., and Mexican Petroleum Co. established offices. Representatives of many other companies visited the district during the first few months of the year. The sudden influx of buyers naturally caused a great rise in prices and this, together with overproduction in the United States, doubtless caused the slowing up of concession transfers in the latter part of the year. The following property transfers occurred: (1) The Gulf Oil Corpn. contract with the Maracaibo Oil Exploration Corpn., whereby the Gulf acquired the right to select 100,000 acres from the Maracaibo's zones. (2) The Gulf Co. purchase of one-quarter interest in seven concessions of the New England Oil Corpn., Ltd. (3) The Gulf Oil Corpn. purchase of several concessions of Kunhardt and others in the Perija district. (4) The Gulf Oil Corpn. purchase of certain portions of the one-kilometer Lake zone that were not covered by parcels or Government reserves (namely the "sobrantes"). (5) Pure Oil Co. purchase of all Government reserves turned back by Maracaibo Oil Exploration Corpn. in the districts of Mara and Miranda. (6) Standard Oil Co.: of New Jersey deal with the British Controlled Oilfields, Ltd., for control of approxi-mately the eastern third of the .district of Buchivacoa, state of Falcon. (7) Royal Dutch deal with the British Controlled Oilfields, Ltd., for the control of the central third of the district of Buchivacoa, Falcon. (8) The Texas Co. purchase of several concessions in Perija and one west of Mene Grande on the east side of Lake Maracaibo. (9) Purchase by the British Equatorial Oil Co., Ltd., of Goverment reserves corresponding to certain Creole Syndicate parcels under the margin of Lake Maracaibo near La Paz. (10) The Lago Petroleum Co. acquired a concession on all of Lake Maracaibo except a 1-Km. strip along the shore.

Jan 3, 1924

By Fred Bond

This paper is a continuation of two earlier papers,1,2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a. new method of measuring the "surface energy" of in ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems.

Jan 1, 1938

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953