Search Documents

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By John W. Crutchfield, Emil F. Bowers

This paper presents the initial results of a pressure maintenance by water return project in the Lower Pawelek reservoir of the Falls City Field, Karnes County, Southwest Texas. Production is from the Lower Wilcox section at an average depth of 6,030 ft on the downthrown side of a "down to the coast" fault. Of particular interest is that the reservoir oil is high gravity and low viscosity but far undersaturated with gas at the original reservoir pressure and temperature. The early pressure and production history indicated only a partial or limited water drive, and this fact, coupled with the characteristics of the reservoir fluid and artificial lifting problem.. made advisable the water injection program to maintain reservoir pressure. The paper includes a description of the reservoir and reservoir fluids, the pressure and production history, a description of the water injection facilities, and the results of reservoir calculations involving Hurst's unsteady state flow and the material balance equations for calculation of water influx and prediction of the pressure-production relationship at various rates of withdrawal. The reservoir calculations and initial field results indicate that reservoir pressures in excess of 85 per cent of original pressure can be maintained by control of water injection even at very high rates of production. INTRODUCTION The purpose of this paper is to report the initial results of a pressure maintenance by water return program in the Lower Pawelek reservoir, Falls City Field, Karnes County. Texas, and to calculate an empirical relationship between pressure and production in this limited or partial water drive reservoir. Location The Falls City Field (Fig. 1) is located two miles north of the town of Falls City in Karnes County, Texas, and is approximately 50 miles south-southeast of San Antonio on U. S. Highway 181. Discovery and Development The initial block of leases was taken after a surface geological survey identified a major east-west fault and closure on the south or downthrown section. The discovery well, Southern Minerals Corporation's Joe F. Bartosch 1; was completed at 4,650 ft in the Lower Bartosch sand in December, 1944. Drilling was continuous until December, 1946, and resulted in the discovery of 12 oil reservoirs between 4,600 and 6,050 ft in the Middle and Lower Wilcox formations. These are shown on the cross-section (Fig. 2). As of the current date there are 64 oil wells completed as follows: Southern Gulfshore Magnolia Minerals Oil Petroleum Reservoir Corp. Co. Corp. Total Upper Bartosch 0 0 0 0 Lower Bartosch 16 0 0 16 Shulze 7 0 1 8 Upper Faires 2 0 0 2 Lower Faires 4 0 0 4 Upper Moczygemba 0 0 0 0 Lower Moczygemha 2 0 0 2 Olinick 2 0 0 2 Upper Martinez 0 0 0 0 Lower Martinez 5 0 0 5 Upper Pawelek 0 0 1 Lower Pawelek 27 1 3 31 Total 65 2 4 71

Jan 1, 1950

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U3O8 /t) (0.80 lb U3O8) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling. Based largely on what we had learned from Western Nuclear's experience, we undertook a program involving a laboratory study to determine the characteristics of the mineral stockpiles, as related to heap leaching, and to conduct a pilot heap leach adjoining our Gas Hill mill. Basically the pilot heap construction and leach procedure were similar to those described in the literature l, 2 with certain modifications to permit detailed monitoring of the operation. In May 1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the following reasons: (1) The necessary equipment for heap construction was readily available. (2) Stockpiles of mineral from the various mining sites were on hand: (3) Construction of the heap could be made on an abandoned tailings pile minimizing problems associated with environmental approval. (4) Proximity of the mill would allow product streams to be absorbed into existing circuits. (5) Necessary utilities were available. (6) Tailings water from the existing circuit could be used for leaching. A program for the pilot heap leach was developed with the following primary objectives. (1) To confirm the data obtained in bench-scale tests particularly on uranium recovery, acid usage, and ore permeability. (2) To evaluate plastic liners used for base preparation. (3) To investigate heap configuration variables. (4) To determine heap leach amenability of the different mineral sources. (5) To establish the economics of heap leaching low-grade ores.

Jan 1, 1979

By Ben L. Seegmiller

Introduction The profitability of an open pit operation depends to a large extent on the use of the steepest pit slopes possible, provided they do not fail during the life of the mine Optimum pit slopes can be designed by using rock mechanics technology. Such technology includes gathering and analyzing pertinent data prior to pit design, rigorous application of rock mechanics principles during the design process, remedial actions to improve slope stability, and monitoring slopes during the life of the mine. Ignoring rock mechanics technology in pit design may place the entire mining enter- prise in jeopardy Disruption of mining operations and safety hazards caused by slope instability can be severe. A classic case in point is the major slope failure (Seegmiller, 1972) that occurred at a southwestern US copper mining operation in 1970-1971 Minor slope stability problems initially amounted to no more than a nuisance, but in time, the unstable zones became larger, causing greater disruption of production and threatening safety Mining at or near the slide toe had continued throughout the period of slope failure, aggravating the already unstable condition The original plan for this pit called for mining the overall pit slope to 37.5" Mine operators were forced to lessen the back- slope angle in the hope that the failing rock mass would stabilize. However, stabilization did not take place, and when mining in the area of failure was completed, the overall slope had been reduced to approximately 27" Mining had been successful in removing only a small portion of the ore body at a high stripping ratio.

Jan 1, 1979

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By L. A. White

IN this paper it is proposed to follow the developments in the design of the lead blast furnace at Port Pirie from the time The Broken Hill Associated Smelters Pty. assumed control in 1915 to the present time, with special reference to the development of the system using two superimposed rows of tuyeres as is now in operation. Lead smelting operations first commenced in 1889, when the British Broken Hill Pty. Ltd. started its first furnace. This was followed by installing two more furnaces during the same year and another the following year. In 1892, Broken Hill Proprietary Co. Ltd. acquired the smelting works and combined operations with those at Broken Hill, New South Wales; by 1897, the whole of the smelting operations had been transferred to Port Pirie and thirteen blast furnaces were built to treat the Broken Hill ore production. In 1915, The Broken Hill Associated Smelters Pty. Ltd. took over from the Broken Hill Proprietary and have carried out operations since that time. From its inception, the present company started on a long range program of reconstruction, in which the development of the lead blast furnace has played a prominent part. A definite trend in plant development has been towards the simplification of plant control by a reduction in the number of operating units. The great advantages of technical control which resulted from the very simplified flowsheet established in the continuous refining process stimulated the desire to extend the principle to the smelting operation. Thus in the sequence of furnaces described here, it will be noted that the trend has been towards larger and, of course, fewer units. With each such development it is significant that the operating conditions and metallurgical results have shown steady improvement. Standard Furnace In 1920 there were seven furnaces operating, five of a type subsequently called the standard furnace and two of the original thirteen smaller furnaces, the latter type being used for the treatment of drosses, etc. produced from the refinery section, while the standard type carried out the main, lead-smelting operations. The standard furnace (figs. 1 and 2) had the dimensions given in table I.

Jan 1, 1951

By Frederick C. Langenberg

IT has been shown1 that copper can be removed from iron-base alloys by solvent extraction with molten lead and sodium sulfide slags. In these processes copper removal is favored by a positive deviation of copper in iron from ideal behavior. Chou' determined the distribution of copper between liquid silver and iron and obtained a value for the activity coefficient of copper in iron at 1600°C, y°, of 9.12. Chipman" calculated the activity coefficient from the Fe-Cu phase diagram to be 12 at 1600°C. More recent work by Koros and Chipman" yields a value at 1600°C for y V equal to 8.0. In this latter work, the distribution of copper between silver and iron was measured at 1600°C, while the activity of copper in the silver phase was determined from calculations based on the Ag-Cu phase diagram. The present work presents another value of based on calculations from the Cu-Pb phase diagram, on the heat of mixing data for the Cu-Pb system, and on an experimental study of the distribution of copper between iron and lead at 1600°C. These experiments were part of a larger research on the removal of copper from iron-base alloys conducted at The Pennsylvania State University. Experimental Procedure—The distribution of copper between pure iron and lead at 1600°C was made in the furnace assembly shown in Fig. 1. The melts were made in high purity alumina crucibles under an atmosphere of prepurified argon. Temperatures were read with an optical pyrometer sighted into a %-in. hole drilled in the inductor. Extensive calibration of the optical readings with immersion readings had been carried out previously. The initial charges consisted of 100 g of electrolytic iron and varying weights of copper. The melts were brought rapidly to 1600°C and 75 g of lead added. The temperature was quickly readjusted to 1600°C, and the melts were held for 10 min at this temperature. A sample was then drawn from the iron layer in a fused silica tube. This sample was analyzed to determine the copper content of the iron layer at equilibrium, while the copper content of the lead layer was determined from a material balance. The validity of the material balance was confirmed by a chemical analysis of the entire lead layer for one heat in which the crucible was removed and quenched after the iron sample was taken. The calculated copper content of the lead-rich phase was 1.18 pct; while the entire lead layer analyzed 1.20 pct Cu. The distribution results are shown in Fig. 2. The distribution constant, N,.'r'"/N, is equal to 3.95. Discussion—From the Cu-Pb phase diagram' it can be seen that lead-rich liquid Pb-Cu solutions

Jan 1, 1957

By C. Q. Payne

The art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates hack to the year 1806, when they were employed in Cornwall, their principal developmcnt has taken place during the past 30 years. To Stephen R. Erom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contrib'ution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the mova, ble roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as, for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springe, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to ex-

Jan 1, 1913

By Ralph W. Bailey, William B. Price

During the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce users of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1. Endurance Limit The majority of fatigue tests are designed to determine the endurance limit of a material. The number of repetitions of stress that will serve to establish an endurance limit varies with different materials. For ferrous materials, H. F. Moore2 has shown that stresses that do not cause failure up to 10,000,000 stress cycles will not cause failure up to 100,000,000 (and sometimes to 1,000,000,000) cycles. Thus an endurance limit for ferrous materials can be determined with a minimum of 10,000,000 stress cycles. For nonferrous materials, no such generalization holds. R. R. Moore3 has shown that for manganese bronze and elektron metal, 13,000,000 and 28,000,000 cycles, respectively, will serve to determine an endurance limit, while certain duralumin specimens gave no indications of having reached an endurance limit up to 400,000,000 stress cycles. J. B. Johnson6 showed that an endurance limit for duralumin was not found by tests running up to 500,000,000 cycles. H. F. Moore2

Jan 1, 1937

By Arvid Anderson

THE weathering of copper-bearing ores with the formation of a water-soluble salt and the recovery of the metal by leaching and evaporation or precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 lb. of copper at an average operating cost, to date, of 3.85 cents per pound at the company's workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 lb. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted.

Jan 9, 1925

By Raymond Ward

Jan 1, 1945

By Lawson P. Entwistle

One of the important reserves of mangani-ferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which has been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. Prom a noselike protuherance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (I) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale. Boston Hill comprises three rolling hills southwest of and adjoining the town of Silver City (pop. 5044), Grant County, N. Mex. The mining district covers less than 2 sq. miles. Silver City, on a branch line of the Atchison, Topeka, and Santa Fe Railway, is a supply point for the important mining communities at Santa Rita, Hurley, Hanover, Tyrone, and Mogollon. The Chloride Flat mining district adjoins Boston Hill on the north. History and Production Bonanza-type silver ores were discovered in the Chloride Flat mining district during the silver boom of the seventies and eighties, at which period it has been credited with as much as $5,000,000 production. In 1916 manganiferous iron ore was first shipped from the Boston Hill mining district to Pueblo, Colo., where it was mixed with manganese ore from Lead-ville and smelted into spiegeleisen. During 1926 and 1927 the Colorado Fuel and Iron Co. mined and churn-drilled part of the district. Mining operations ceased during the depression of the thirties, but production was resumed in 1937. Since 1916 the Boston Hill mining district has produced about 600,000 long tons of ore averaging about 12 per cent manganese and 35 to 40 per cent iron.

Jan 1, 1949

By J. W. Mitchell

Season cracking of 70-30 cartridge brass cases of small arms and artillery ammunition has been under investigation at the Frankford Arsenal for many years. The nature of this stress-corrosion failure has been found to be intergranular. Much of this work, however, has been directed toward improvements in method of manufacturing the cases so as to reduce the tendency to season crack and little progress had been made toward finding the source of the chemical agent producing the inter- granular corrosion. Ammonia has been shown to produce season cracking in brass and is known to be present in certain atmospheres, particularly industrial, in sufficient concentration to cause cracking. However, in the case of small arms ammunition, the hypothesis that atmospheric ammonia is the cause will not hold, since small arms ammunition is hermetically sealed during storage and yet occasional lots are found to have cracked after 3 to 5 yr. storage. Much of the early study of season cracking in small arms ammunition was done by Nicholas H. Murdza of the Frank- ford Arsenal. In 1936, he suggested that the corrosive agent might be one of the decomposition products of smokeless powder and mentioned nitrogen oxides specifically. Then in 1937, Murdza suggested that the breakdown of smokeless powder in storage resulted in the formation not only of nitrogen oxides but also ammonia

Jan 1, 1945

By T. N. Williamson

6.3-1. Historical Development. Rotary drilling has been used in surface mining for many years. Its principal use is for primary blasthole drilling. In this use, holes in the range from 4 to 15 in. in diameter are drilled in overburden and massive ore bodies for large initial blasting operation. With properly designed shot patterns and loading, secondary blasting is seldom required. The use of rotary drilling with diamond bits for exploration is discussed in Chapter 3.1. Small rotary drillholes of approximately 2-in. diameter are employed as blastholes to shatter uncovered coal seams, but this is a minor part of surface mining drilling operations. Another minor use of rotary drills in surface mining is for placing wire saw poles in dimension stone quarries, usually accomplished with large-diameter calyx or steel shot drills. Primary blasthole drilling by the rotary method was performed with drag bits until 1949 (19). Its use in mining was only in soft formations, so that rotary drills prior to that time were found principally in overburden drilling for the surface mining of coal. In 1949 it was found that air circulation to remove cuttings resulted in increased penetration rate and prolonged life for the rolling-cutter type of bits. Prior to that time, and since their introduction in oil well drilling in 1907, water had been used for circulation with these bits. The dependence on water to clean the hole had delayed the acceptance of bits with rolling cutters in mines because of water haulage and freezing problems as well as the loss of water through cracks in the formation. After rolling cutters were introduced, subsequent improvements in tools made rotary drilling adaptable to harder formations (18). This system is now used in the hardest formations encountered in mining. 6.3-2. Principles of Operation. ENERGY. Rotary drills attack rock with energy supplied to the bit by a rotating drill stem, and infrequently by

Jan 1, 1968

By W. R. Finlay, W. R. Jr. Hibbard

The key feature of the lattice coherency theory of precipitation hardening1 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.6'6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: rz pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pet copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,~ studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkins~n,~ in 1944, applied tensile creep stresses to a complex copper. nickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1949

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in