Search Documents

By Robert L. Fleischer

A well known but unexplained experimental fact is the observation1 that aluminum shows a pure <111> wire texture, in contrast with other fcc metals, which have a mixed <100> <111> texture at moderate reductions. A possibly related single crystal observation on aluminum is the following:2 under tensile deformation <111> single crystals are stable (maintain their original axial orientation), while <100> crystals are unstable at room temperature and become stable at lower temperatures. This suggests that at room temperature, as proposed by Yen and Hibbard,3 the single <111> texture obtains be- cause <100> orientations are unstable in the poly-crystal. It also implies that for wire drawing at lower temperature a <100> component of the texture might be expected since that orientation is then stable. This possibility has been examined by wire drawing at temperatures near 77°K. The apparatus was designed to be used with an existing draw-bench, a steel trough acting as die holder and containing sufficient liquid nitrogen to immerse the wire entering the die. The trough is insulated by a styrofoam container to prevent excessive boiling of the bath. The wire emerging from the die enters a polyethylene tube, into the far end of which the grips are inserted. Liquid nitrogen is funneled into the tube to maintain the low tem-

Jan 1, 1962

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDERSON, AMIL A., Co. A, 309th Regiment Engineers, 84th Div., American E. F., Care Postmaster, New York. ARMSTRONG, HAROLD K., Pilot, Naval Aviation, U. S. Naval Air Station, Miami, Fla. BASSETT, ARTHUR F., Co. 6, -E. 0. T. S., Camp Humphreys, Va. BEDDALL, THOMAS H., Adjutant, 1st Battalion, 1st Gas Regiment, American E. F. BERNARD, CLINTON P., Candidate, 12th Observation Battery, F. A. C. 0. T. S., Camp Taylor, Ky. BROOKE, LIONEL, 50th Co., 13th Battalion, 5th Replacement Engineers, Camp Gordon, Ga. BROWNING, EDWARD, Corp., 1st Regiment Engineers, Co. D, American E. F. BUGBEE, EDWARD E., S. A. T. C. Headquarters, Raleigh N. C. BUTTERFIELD, G. BRUCE, CO. C, 605th Engineers, American E. F. CADOT, J. J., 1st Lieut., U. S. Air Service, American E. F., Care Post- master, New York. CARLOCK, J. B., Major, 2d Battalion, 1st Gas Regiment, American E. F., France.

Jan 12, 1918

By C. W. Sherman, J. Chipman, H. I. Elvander

THE pronounced and usually deleterious effects of sulphur on all ferrous metals and the resultant necessity for its control in metallurgical processes have stimulated many investigations of the system iron-sulphur. The data required for thermodynamic study of the behavior of sulphur in molten iron and steel include the activity and free energy of the dissolved sulphur and its heat of solution. Such data are also of theoretical interest since there is all too little information available concerning solutions of nonmetallic solutes in metallic solvents. It was the purpose of this investigation to attack the problem very directly by a study of equilibrium at several temperatures in the reaction H2 (gas) + S = H2S (gas) [1] K1 = PH2S /PH2 as where the sulphur is present in the liquid iron in amounts up to several percent by weight. Such a method of attack is not new since several careful studies have already been reported. It is planned, however, to extend the study to other metallic solvents and particularly to determine the effects of the various alloying elements on the activity of sulphur in liquid iron. This paper presents the results on molten iron-sulphur alloys containing up to 4 pct sulphur in the temperature range 1530°-1730°C. Literature Review The significant researches on dilute molten solutions of sulphur in iron include those of Chipman

Jan 1, 1951

By W. B. Price

AT the New York meeting of the American Institute of Mining and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."&apos; The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. Protuberances on Admiralty Brass In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig. la) and upon analysis was found to contain 66.66 per cent. copper, 4.02 per cent. tin and 0.03 per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and 0.01 per cent. lead. A sample of the shaggy-rough protuberances at the very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation." Fig. 16 is a cross-section of a bar through the protuberances on the surface. It reveals that there is a decidedly different structure through the raised areas and seems to indicate that the bar originally solidified

Jan 1, 1927

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969

By Herty, C. H.

One of the numerous requirements of many grades of present- day steel is that the steel shall be free from non-metallic inclusions. These inclusions may be composed of oxides, sulphides, complex oxy- sulphides, and nitrides, which enter the steel with the furnace charge, result from sulphur absorption from the furnace gases, or are formed in the steel during the deoxidation process. Although few&apos; data are available which indicate in any quantitative manner the specific effects of inclusions in steel, there is a large mass of circumstantial evidence which points to the advisability of producing steel free from these impurities for many purposes. At the present time there is a growing feeling among metallurgists that non-metallic inclusions should be divided into two distinct types: (I) those readily visible under the microscope at ordinary magnifications; and (2) those in colloidal suspension or in solid solution. Both types are profoundly influenced by the character of the charge, the manipulation of the furnace slag, and the method of deoxidation. The work described in this bulletin deals primarily with inclusions visible under the microscope at ordinary magnifications, but the steels made by the various methods of deoxidation are being used LO study certain effects which may be ascribed to the second classification, named above. This latter work will be the subject of further bulletins on the effect of deoxidation practice on the physical properties of the steels involved.

Jan 1, 1957

By Gieskieng, D. H.

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely different materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected

Jan 1, 1949

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200&apos; C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contamination could be reduced about 80 pct. The water company&apos;s supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters, and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West P~M Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs sup- plying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical "Coal Measures"

Jan 1, 1949

By Chikao Nishiwaki

INTRODUCTION The Japanese dependency for mineral raw materials from foreign sources increased rapidly within the 20 years since the Korean war. During this 20 year period Japan has attempted to industrialize and develop her economy while depending mostly on heavy import of nearly all kinds of mineral raw materials. She has fabricated them using energy generated mostly by mineral fuel that are also imported. Fabricated goods are either used domestically to accelerate more fabrication industry or exported after adding more refinement or fabrication. In this paper iron ore as a major raw material for the Iron and Steel industry, three major base metals, copper, zinc and lead, and petroleum as a major energy source have been selected as examples to represent the general features of various kinds of mineral raw materials that are imported. Among other important mineral commodities for which Japan dependa upon foreign sources are: Aluminium, nickel and cobalt, potash and phosphorous 100 percent dependent and tin, tungusten, chromium and molybdenum over 95 percent dependent. IRON ORE Statistics for the important iron and steel raw materials, namely iron ore, coal and scrap iron are shown in Tables 1, 2 and Fig. 1. Iron ore is by far the most important and basic among these three commodities. There has been practically no steel or iron imported as a metal into Japan during this period. Iron ore, including aggregate such as pellets, and metallurgical coal are mostly transported in large ore cargo boats to the port where very efficient port facilities unload them directly at the steel mill site. As a result

Jan 1, 1976

By Frank Armstrong

ALL the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors FIG. 1.-ELECTRO-HYDRAULIC SHOVEL FIG:. 2-THE SHOVEL AS IT WAS OPERATED CINDER CONSTRUCTION. THE FIRST YEAR. and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the; steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 2, 1916

By A. Spilners, M. Simnad

The rates of formation of the different oxides on molybdenum in pure oxygen at 1 atm pressure have been determined in the temperature range 500° to 770°C. The rate of vaporization of MOO, is linear with time, and the energy of activation for its vaporization is 53,000 cal per mol below 650°C and 89,600 cal per mol at temperatures above 650°C. The ratio Mo03(vapor.lzing)/MoOS3(suriace) increases in a complicated manner with time and temperature. There is a maximum in the total rate of oxidation at 6W°C. At temperatures below 600°C, an activation energy of 48,900 cal per mol for the formation of total MOO, on molybdenum has been evaluated. The suboxide Moo2 does not increase beyond a very small critical thickness. At temperatures above 725°C, catastrophic oxidation of an autocatalytic nature was encountered. Pronounced pitting of the metal was found to occur in the temperature range 550° to 650°C. Marker movement experiments indicate that the oxides on molybdenum grow almost entirely by diffusion of oxygen anions. USEFUL life of molybdenum in air at elevated temperatures is limited by the unprotective nature of its oxide which begins to volatilize at moderate temperatures. Although the oxide/metal volume ratio is greater than one, the protective nature of the oxide film is very limited. Gulbransen and Hickman&apos; have shown, by means of electron diffraction studies, that the oxides formed during the oxidation of molybdenum are MOO, and MOO,. The dioxide is the one present next to the metal surface and the trioxide is formed by the oxidation of the dioxide. Molybdenum dioxide is a brownish-black oxide which can be reduced by hydrogen at about 500°C. Molybdenum trioxide has a colorless transparent rhombic crystal structure when sublimed, but on the metal surface it has a yellowish-white fibrous structure. It is reported to be volatile at temperatures above 500" and melts at 795°C. It is soluble in ammonia, which does not affect the dioxide or the metal. In his extensive and classic investigations of the oxidation of metals, Gulbransen2 has studied the formation of thin oxide films on molybdenum in the temperature range 250" to 523°C. These experiments were carried out in a vacuum microbalance, and the effect of pressure (in the range 10-6 yo 76 mm Hg), surface preparation, concentration of inert gas in the lattice, cycling procedures in temperature, and vacuum effect were studied. The oxidation was found to follow the parabolic law from 250" to 450°C and deviations started to occur at 450 °C. The rates of evaporation of a thick oxide film were also studied at temperatures of 474" to 523°C. In vacua of the order of 10- km Hg and at elevated temperatures, an oxidation process was observed, since the oxide that formed at these low pressures consisted of MOO, which has a protective action to further reaction in vacua at temperatures up to 1000°C. Electron diffraction studies showed that, as the film thickened in the low temperature range, MOO8 became predominant on the surface. Above 400°C MOO, was no longer observed, MOO, being the only oxide detected. The failure to detect MOO, on the surface of the film formed at the higher temperatures does not militate against the formation of this oxide, since according to free energy data MOO3, is stable up to much higher temperatures. At the low pressures employed, this oxide would volatilize off as soon as it was formed. Its vapor pressure is relatively high and is given by the equations" log p(mm iig) = -16,140 T-1 -5.53 log T + 30.69 (25°C—melting point) log p(mm He) = -14,560 T-1 -7.04 log T+1 + 34.07 (melting-boiling point). Lustman4 has reported some results on the scaling of molybdenum in air which indicate a discontinuity at the melting point of MOO, (795°C). Above the melting point of MOO,, oxidation is accompanied by loss of weight, since the oxide formed flows off the surface as soon as it is formed.5,6 Qathenau and Meijering7 point out that the eutectic MOO2-MOO3 melts at 778C, and they ascribe the catastrophic oxidation of alloys of high molybdenum content to the formation of low melting point eutectics of MOO3 with the oxides of the melts present. Fontana and Leslie -explain the same phenomenon in terms of the volatility of MOO,, which leads to the formation of a porous scale. Recent unpublished work by Speiser9 n the oxidation of molybdenum in air at temperatures between 480" and 960°C shows that the rate of weight change of molybdenum is controlled by the relationship between the rates of formation and evaporation of MOO,. They have measured the rates of evaporation of Moo3 in air at different temperatures and estimated an activation energy of 46,900 cal. This compares with the value of 50,800 cal per mol obtained by Gulbransen for the rate of sublimation of MOO, into a vacuum.

Jan 1, 1956

By Walter E. Hopper

(Wilkes-Barre Meeting, June, 1911.) I. LOCATION AND EXTENT. THE Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five rail-road-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. II. HISTORY AND DEVELOPMENT. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser " Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905, four wells were drilling. Great trouble was experienced with

Apr 1, 1911

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

By George A. Laird

I. INTRODUCTION. THIS old and once famous district played, through its enormous production of silver and gold, an important part in the history of the State of San Luis Potosi. According to a pamphlet prepared under the direction of the Governor of the State, Sr. Don Blas Escontria, and presented to the visiting members of the Institute during the Mexican meeting of 1901, this district is situated 20 km. east of the city of San Luis Potosi, in a range of mountains of moderate height, extending 135 km. N. and S., and 16 km. E. and W.; and the mineralized area hitherto developed is about 600,000 sq. m. The history of the district,. as given by the record dated 1778, and formerly kept in the San Francisco convent, says that it was discovered in 1575 by Sr. Don Pedro Irarte, and adds that the city of San Luis Rey de Francisco del Potosi received its name (in allusion to the famous Potosi mines in Bolivia) by reason of the remarkable productiveness of its gold- and silver-mines in the first period of their exploration, during which they paid to the Crown, as " quintos " (the fifth part of the product), $97,000,000, as appears from the accounts of the royal treasury. The amount of the quientos paid during the " bonanza period " of 80 years was $72,000,000. The larger sum first mentioned probably represents a longer series of years. But either will suffice to indicate the great wealth of the mines. In 1663, the decadence of the industry began with the caving¬ in of several mines, concerning which the record of 1778, al¬ready cited, says, in substance, that on Good Friday one of the owners in the enterprise, in view of the unfavorable prospect of a lawsuit in which he was engaged, set fire to the timbers supporting the underground galleries and workings of the San

Jan 1, 1905

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By Paul E. Melancon, Vincent C. Kelley, Dale F. Kittel

Uranium of the Grants region occurs predominantly in continental sandstones of the upper part of the Jurassic Morrison Formation, but significant lesser deposits are found in limestone of the Jurassic Todilto Formation and in black shale of the Cretaceous Dakota Formation. The deposits are disseminations that form runs ranging from a few hundred tons to several million tons. The ore consists mainly of uraninite, uraniferous carbonaceous material, coffinite, and such secondary oxidized minerals at tyuyamunite, carnotite, and uranophane. In sandstone, the ore runs were locallized by mudstone, interstitial carbonaceous material, and primary sand channel trends. In limestone, ore deposition was related to folds and fracture zones. The great bulk of production has come from the Ambrosia Lake mines in the Grants district and the Jackpile and Paguate mines in the Laguna district. The ores, which generally have been 0.20 to 0.30 per cent U3O8, are treated at mills operated by Kerr-McGee Corporation, Homestake-Sapin Partners, and The Anaconda Company, all in the Grants district. In 14·years after discovery in 1950, the deposits had yielded concentrates valued in excess of $800,000,000. Since deposition of the Jurassic host rocks, a geologic history involving tilting, faulting, erosion, changing ground-water environments, and oxidation has considerably influenced the existence and character of the deposits. It is evident that their ongm is not simple. However, a degree of agreement appears probable for a pre-Dakota age for the original ore runs, and, at Ambrosia Lake, two principal stages of ore formation, separated by Laramide faulting, are recognized. All earlier ores have been modified by Quaternary oxidation, solution, and enrichment during which time much secondary tyuyamunite, metatyuyamunite, carnotite were formed.

Jan 1, 1968

By J. HUNER

Twenty-four new fields were found in Louisiana during 1945. Of this number 15 were oil fields, eight were gas condensate, and one a dry gas field. None of these fields, with the exception of West Delhi, is as yet of any great consequence. The Weeks Island field in Iberia Parish may eventually develop into a considerable reserve.

Jan 1, 1946