Search Documents

By M. E. Wadsworth, P. H. Yu, C. K. Hansen

A study of the rate of dissc5lution of chalcopyrite (CuFeS2) in acidic solutions under oxygen overpressures was carried out by measuring the rate of formation of cupric ions in solution. Effects of temperature, oxygen partial pressure, surface area, and concentration of sulfuric acid were evaluated. A sized batch of chalcopyrite was leached in the temperature range of 125° to 175°C and in the pressure range of 75 to 400 psi of oxygen. In 0.5 N H2SO4 all products of reaction went into solution except for trace amounts of elemental sulfur. The dissolution of chalcopyrite followed linear kinetics and was essentially independent of hydrogen ion concentration for H2S04 concentrations between 0.2 and 0.5 N. The oxygen dependence indicated adsorption approaching limiting values with increasing oxygen pressure. The linear mechanism was explained in terms of steady-state adsorption of oxygen at the chalcopyrite surface followed by a surface reaction. The enthalpy of activation for adsorption of oxygen was found to be approximately 33 kcal per mole. An activation enthalpy of approximately 9 kcal per mole was observed for the surface reaction. Charge transfer reactions are not rate controlling in the process.

Jan 1, 1973

By H. K. Shearer

Oil production in north Louisianat in 1939 was 25,249,640 bbl., a decrease of 11.2 per cent from 1938. The only important increases in production were in the Cotton Valley and Shreveport fields, but Caddo, Homer, Sligo and Zwolle also made slight gains. Greatest decreases were in the Lisbon and Rodessa fields. Xatural gas production of 313,333 million cu. ft. was an increase of 5.6 per cent over 1938. The increase was accounted for in the Monroe field, while all other fields showed only minor variations from the production of the previous year. Well completions in 1939, as compared with 1938, were as follows: The decline in number of completions was due entirely to lack of proved areas for drilling, and would have been greater except for a revival of interest in the old Caddo shallow field. A majority of the wells completed during the year were in various old, shallow fields, so the average depth of drilling was much less than in several preceding years, notwithstanding a few very deep tests. No new fields were discovered, the only wildcat well reported as a producer being a very small oil well in northwestern De Soto Parish, which is of no apparent commercial importance. Deep gas-distillate production in the Cotton Valley formation was opened at Lake Bistineau and Lisbon, and oil at Shongaloo, but all these wells were too small to encourage additional drilling. Extensions and Developments Caddo Field.—More active drilling was donc in the 36-year old Caddo field in 1939 than in any of the newer fields, with completion of 133 oil

Jan 1, 1940

By John G. H. Crump, E. W. Owen, Peter P. Gregory

.Although oil Production in West Texas in 1939 reached the highest figure for any year since the inauguration of proration, drilling activity continued in the decline that had commerlced the previous year. Production totaled 79,469,341s bbl. of oil during 1939 as compared with 71,257,541s bbl. in 1938 and 75,743,000 in 1937. The number of wells completed in 1939 was 1850, compared with 2045 in 1938 and 2806 ill 1937. Several factors combined to cause the decrease in drilling activity, principally the contiriued increase in the length of time required to obtain a return of invcstment and the scarcity of important new discoveries during the past two years. Of the 1850 completions 1638 resulted in oil wells, 4 were gas wells, 168 were dry holes and 40 were abandoned locations; 1990 new locations were made during the year. The ratio of dry holes to producing wells completed was one dry hole to each 9.75 oil wells, compared with one dry hole to each 7.48 oil wells completed during 1938. This large decrease in dry holes was due to a marked decline in the number of wildcat wells drilled, there having been only 120 wildcat completions during 1939. In addition to the lessened exploration work, the deeline' in activity was largely accounted for by the slowing up of operations in the older pools of Ector, Howard and Winkler Counties. Ector County, which had led West Tcxas in 1938 with 622 new oil wells, furnished only 485 producers in 1939, but was still the leader for the West Texas district. The largest gain in activity was in Yoakum County, whew 350 oil wells were completed in the Denver-Wasson field against 152 during 1938. Most of the older oil fields have been almost completely drilled up, only a few new producers still being completed from time to time in

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By Will H. Coghill, Fred D. DeVaney, R. G. O’Meara

The size of ball mills in the ore-dressing industry has increased from about 4 ft. in each dimension to 10.5 ft. in diameter by 8 ft. in length. In the cement industry they are as long as 45 ft. Plainly the trend has been toward larger mills. The common belief is that the big mills economize in floor space and first cost, but the advantage with respect to friction has not been clearly defined. In the ball-mill studies at Rolla, Mo., laboratory mills as small as 2 by 2 ft. have been found as efficient in terms of the amount of grinding per unit of net power as mills 6 by 4 or 6 by 12 ft. Therefore, if supremacy can be claimed for the big mills, advantage must come from other sources. The advantage to be considered here is reduced loss by friction or dead load. In the study to determine whether big mills have relatively less loss by friction the commercial catalogs were used for fundamental figures. The dimensions and weights of Table 1 are taken from the catalogs (the last line gives data on a Rolla laboratory mill). The net power—that is, the power expended within the mill for grinding—is calculated by a new formula.' The assumed speeds are each at 70 per cent of their theoretical critical speeds, and the mills are loaded to the center with balls. In other words, they are assumed to be working under analogous conditions and are set for good grinding. In the last column the ratio B: A shows that the larger commercial mills are lighter per unit of net power than the smaller mills, and more of the motor output should therefore go into grinding. The laboratory mill seems to have some advantage over the larger mills; it would be expected to be light because it has no liners.

Jan 1, 1935

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Septa 10, 1917, to Oct. 10, 1917. ALDER, ALFRED 1020 Kansas City St., Rapid City, So. Dakota. AUBEL, VERNE WALLACE, Night Supt. of Works, Broken Hill Proprietary Co., Ltd., Newcastle, N. S. W., Aust. BAKER, ROBERT EARL Works Mgr., Keokuk Electro-Metals Co., Keokuk, Iowa. BALLAMY, JOHN H., Min. Engr., Delaware, Lackawanna & Western Railroad Co,Scranton, Pa. BRADLEY, ALLEN PALMER, Met., American Smelting & Refining Co., Murray, Utah. BRIGGS, WALTER M Pres. Regal Mines Co. Dedham, Mass. BRONSON, EDMOND B., Pres., Bagdad Copper Co., 120 Broadway, New York, N. Y. BROOK, NILES WINFIELD, District. Mgr., Cleveland Min. Co., 625 Bank & Insurance Bldg., Dubuque, BUSKETT, EVANS 1V., Assayer, Custom Assay Office, 620 Joplin St., Joplin, Mo. CAMPBELL, JOHN HATES, Chem. Engr., Robert W. Hunt. & Co., 2200 Insurance Exchange, Chicago, Ill.

Jan 11, 1917

By W. D. Klopp, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

The purification of commercial-purity tantalum powder by vacuum sintering in the temperature range 2600° to 2860°C has been investigated. Mixtures of tantalum oxide and tantalum carbide were sintered at 1800° and 2200°C. Tantalum bars containing 1 pct additions of oxygen, nitrogen, and carbon. were sintered in the range 1800° to 2600°C. Anulyses were conducted on the sititeyed mixtures to determine the extent of removal of oxygen, nitrogen, and carbon at each sintering condition. The mechanism for remova1 of each impurity, and the conditions necessary for preparing ductile tantalum by vacuum sintering are discussed. INTEREST in the refractory metals has been stimulated in recent years by the need for structural materials capable of operating at temperatures of 1100°C and higher. These metals include columbium (niobium) (mp 2468°C), molybdenum (mp 2620°C), tantalum (mp 2996°C), rhenium (mp 3160°C), and tung- sten (mp 3415°C). In addition to its high melting point, tantalum possesses the advantages of forming a solid, nonvolatile oxide at temperatures of interest and of being ductile and easy to fabricate. The classic method of consolidating tantalum from powder refined from the ores is by vacuum sintering at temperatures on the order of 2600°C. This sintering treatment both densifies the compacted powder bars and purifies the metal by causing impurities to boil out. The present work was undertaken to provide more quantative data on the relationship between sintering conditions and purity and to determine the mechanisms of impurity removal.

Jan 1, 1961

By Charles Means

A THOROUGHLY modern coal-handling system has been installed at the Pittsburgh Terminal R. R. & Coal Co.'s new No. 8 shaft, or Coverdale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur f the Montour R. R. The Pittsburgh seam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with their remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. MINE SUBSTATION The transformer substation is adjacent to a pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies.

Jan 9, 1921

By E. W. Johnson, M. L. Hill

The dijfusiuity D was determined at 25° to 780°C- from hyd?-ogen evolution rates. Anomalous evolution from air-melted iron was att~zbztted to residual hydrogen, which is interpreted as a hydrogen compound that decomposes at a strongly temperature-(Ieperzdent rate above 500°C. Above 200°C, D = 0.0014 cm2sec-1 exp (-3200 cal per g atom/RT). Below, 200°C the diffusivity is anomalously low and represented by D = 0.12 cm2sec-l exp (-7820 cal per g atom/RT). It is postulated that at low temperatures the hydrogen in the metal is "trapped" with an energy 4.8 kcaL per g atom below- that of the interstitial hydrogen. 1 HE purpose of the present experimental study was to determine the diffusivity of hydrogen in a-Fe over an extended temperature range. As certain anomalies were encountered, attempts were made to understand the anomalies themselves. This research was in progress both before and after a determination of the diffusivity of hydrogen in nicke1.l The latter system was found to exhibit none of the anomalies of hydrogen in iron, and its description was far simpler. The experiments on nickel also

Jan 1, 1961

By R. L. Tobie

The degree of automation that has evolved in the dumping and hoisting of ore at the 3A and 3B hoisting shafts of the San Manuel mine is discussed. Motormen underground now dump their own trains at shaft pockets with rotary car dumps which operate semiautomatically. The ore is then drawn out of the 1200-ton shaft pockets into measuring baskets in skip loading stations, loaded into bottom-dump skips, hoisted, and dumped into coarse ore bins on the surface, in a fully automated operation. In an underground control room on the 2075 level midway between 3A and 3B shafts, car dumping, skip loading, and hoisting systems are monitored on lighted control panels which mimic each step in the operation. Here skip loading and dumping are viewed on closed-circuit television.

Jan 1, 1972

By Wm. J. Wright

RECORDS of crude oil in India date back for nearly 100 years, and modest attempts were made to develop the oilfields of Assam about 75 years ago. We have no record of production until 1892 when the fields near Digboi, Assam, yielded about 700 bbl. Since that time, the production of the Digboi fields has increased slowly, but steadily, and new fields have been opened at Badarpur, in Assam, and Khaur, in the Punjab, until the production in India in 1918 was about 293,700 bbl. and the possible production at the present time is approximately 300,000 bbl. per year. In the meantime, the English oil companies in India have been slowly adding to their holdings until they have taken up practically all of the promising territory that is readily accessible, and only about one-tenth of their properties has been touched by the drill. All the producing oilfields of India, and as far as we know all the prospective fields, are confined to areas underlain by rocks of Tertiary age. These rocks consist of more than 20,000 ft. of dark sandstones and shales, with the Nummulitic (Eocene) limestone at the base. In parts of Assam, the lower measures contain economic deposits of bituminous coal. In the Punjab, the upper part contains thick beds of conglomerate. Visible organic remains are rare; except in the limestone and the coal measures. In general, the hardness of the measures increases from top to bottom, but there is an alternation of relatively hard and soft beds throughout the whole series. The rocks are everywhere folded and, in some instances, severely faulted. The crests of eroded anticlines usually stand up as ranges of hills in which the individual ridges are underlain by the relatively' hard beds. Thus structural features are suggested and often clearly defined on the topographic maps.

Jan 3, 1924

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By H. J. Wasson

Published literature regarding the nation's oil reserve has been largely concerned with the estimated quantities in sight in known producing fields. This proved reserve has never been large in relation to demand. It has been the practice to consider the total future reserve (beyond that in sight within known fields) in the light of the broad potentialities of vast areas of partially explored sedimentary rocks, which are regarded as possible oil territory. Until recently, but little attention has been given to the rate at which the unexplored potentialities may be. converted into the proved reserve classification. To a certain extent, therefore, our contemporary viewpoint on the subject of national oil reserves is characterized by a pronounced contradiction. On the one hand, we measure known reserves as sufficient for only a few years of consumption—i.e., relative scarcity; on the other hand, we are confident that millions of unexplored acres will yield many new oil fields and that countless deeper productive formations underlie many of our known productive fields—i.e., infinite abundance. Of greater significance than the quantitative measure of either of these reserve classifications is the rate at which reserve replenishment must be accomplished in order to maintain an adequate time supply of proved oil reserves. The accumulation of geological data covering broad areas supports the belief that the remaining undiscovered oil reserve is exceedingly large. The distribution of oil in sedimentary formations of practically all ages, from Cambrian to Recent, is suggestive of almost unlimited possibilities; and the relatively small proportion of these possible areas that has been intensively explored in this country is a further index of the probable magnitude of the undiscovered future reserve. The implication that may reasonably be drawn from these observations is that oil, though distributed with less regularity and concentration than its related hydrocarbon, coal, nevertheless is a relatively abundant natural commodity of which the exhaustion appears remote. Final exhaustion of our oil reserve, if not infinitely remote, is a future contin-

Jan 1, 1937

By R. R. Seeber

In the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large—from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.' The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting ing-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. The hoist for No. 4 shaft is about 1,700 ft. from the power-plant, arid in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-geaerator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-km, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels

Jan 1, 1911

By Paul T. Allsman, E. W. Newman

TRENCHING, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively.

Jan 1, 1944

By K. V. S. Sastry, M. Cross

A summary of recent progress in understanding the main factors affecting the pelletization of fine particles is presented. A scheme for categorizing the mechanisms responsible for pellet growth is out- lined and laboratory methods to both identify the important growth mechanisms and quantify the effects of the major factors influencing the rate of pelletization are described. Next laboratory and mathematical simulations of the commercial process involved in pelletizing iron ore concentrates, are presented. The operational instabilities associated with this pelletization process are described and subjected to a control theory analysis. This analysis, in conjunction with the mathematical models, is used to both explain existing control problems and assess the effectiveness of possible circuit redesigns at producing a more stable and controllable operation. Although much of the discussion is in the context of iron ore pelletizing the approach developed to analyze the agglomeration behavior of these concentrates should apply to most other fine particle systems.

Jan 1, 1980

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984