Search Documents

By S. F. Shaw

The Sierra Mojada mining district is situated in western Coahuila, about 8 km. east of the Chihuahua state line, and about one-half way from the northern to the southern extremity of the state. It is at the terminus of the Mexican Northern R. R., 125 km. northeast of Escal6n, Chihuahua; also about, 240 km. due west of Monclova, Coahuila. The altitude is approximately 1500 m. above sea level. The Sierra Mojada valley is about 10 km. long, from east to west, with a width of 1 to 2 km. It is approached from the east through the Puerto del Oro, where the Mexican Northern R. R. enters the valley; the slope from west to east is gentle. The Sierra Mojada, of which about 300 m. is an almost vertical wall, bounds the valley on the south side; on the north side, the slope to the crest of Sierra Planchada is more gradual, rising only 200 or 300 m. above the valley. Water is relatively scarce in the district, and there are no running streams. The rainy season, usually beginning at the middle of June, lasts through July, and occasionally into August or September. In some years the rains fail entirely. The slope of the ground is such that nearly all the water immediately runs off. The arroyos along the flanks of the mountains are not very deep, but in heavy rains, sometimes approaching cloudbursts, a tremendous volume of water rushes down them, carrying large boulders. A certain amount of seepage collects in the agglomerate, lying below the conglomerate, and is retained in the local fractures. Some shallow wells have been sunk in this agglomerate, and one well over 150 m. deep was sunk on the Volcan ranch, supplying about 76 1. (20 gal.) per min. A considerable supply of water is collected in large earth reservoirs in and below the town of Esmeralda. In ordinary years this supply will last until January or February, after which the Volcan well has to be depended on until the next rainy season. Vegetation is scarce, aside from scanty scrub oak and other brush in the mountains, and a few mezquite, locust, pepper, and cottonwood trees

Jan 1, 1923

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By Benjamin L. Miller, Charles H. Breerwood

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Chester A. Fulton

In Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screening of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated draglines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient operations, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida's largest port on the Gulf coast. The geology1 of these phosphate pebble deposits may be described briefly. A fairly pure limestone was altered to a secondary apatite.

Jan 1, 1938

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By Harlowe Hardinge

The sound made by ball, pebble and rod mills has long been used by the operator as the "telltale" of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill under the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control. Relation of Sound to Useful Grinding Energy Experience has taught us that there is a difference in character as well as in intensity of sound between a mill grinding wet and one grinding dry, in open or closed circuit, to obtain a coarse or fine product, on the same material, to say nothing of the effect with a variety of different materials. Broadly speaking, a wet-grinding mill operates best at a lower sound level than the same mill grinding dry, with other conditions the same. Several reasons for this variation in sound intensity under these conditions can be advanced, but the important point is that there is a difference, based upon practical results. Since these reasons may be more or less involved, and may be subject, to much discussion, only one will be considered here. It is apparent that two balls hitting together or a ball striking the lining, if there is no intervening material, will produce the maximum sound. If a complete cushion of material is placed between the balls or ball and liner, so that the energy is dissipated without doing useful work, the balls will be unable to create enough pressure or force to fracture the particles, and the sound will be at a minimum. At some point in between—that is, where there is sufficient material between the balls or ball and liner so that the ball will fracture the particles without mashing them unduly—the sound

Jan 1, 1939

By Gregoire Gutzeit

The development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution's research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. General Outline The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. . The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof's rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties—for instance, isotropism, anisotropism, color, cleavage, reflecting power-—are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel's photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1943

By E. R. Borcherdt

Methods and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. Exploration Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. For many Years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both Ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in Ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1943

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at sub-critical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.' Westgren, Phragrnén and Ne-gresco2 identified the following carbides in chromium steels: Cementitc............ Fe3C (containing up to about 15 per cent Cr) Trigonal carbide...... Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide........ Cr4C (or Cr23C6) (con- . taining up to about 25 per cent Fe) Orthorhombic carbide , cr3c2 (containing only a few per cent Fe) The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus,4 By means of dilatometric and microscopic stzdies, sections of the diagram were established. This diagram showed the presence of the special carbide CI7C3 in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in I per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7C3 occurs in chromium steels containing more than about I per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. Experimental Procedure The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into I-in. round bars, and all heat-treatments were conducted on specimens of this section size. Sections of the bar stock 8 in. long were hardened in air, oil or water, depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after quenching. The quenched bars were cut into

Jan 1, 1942

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By M. Cohen, B. L. Averbach

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949