Search Documents

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By James Humes

THE active mines in the Park City district at the present time are the Silver King Coalition, Daly-Judge, Daly West, and Silver King Consoli¬dated. Several other companies, such as the Daly, American Flag, Ontario, etc., are doing considerable development work. In the Silver King Coalition mines the ore is a replacement of a dark siliceous limestone bed, varying in thickness from 18 in. to several feet. In places the ore has reached a thickness of 25 ft. This limestone bed lies within 100 ft. of the underlying Weber quartzite. There are other lime beds, similar in appearance to this one, in the Park City formation, which is approximately 700 ft. thick; but not one of them has been found to contain any traces of ore. Directly under and in contact with the ore-bearing bed is another, composed of gray lime well studded with dark concretionary nodules; and this one is an unfailing indication of the proximity of the ore-bearing bed. These ore deposits make out from or have connection with some one of the ore-bearing fissures, which were undoubtedly the channels for the circulation of mineral-bearing solutions. It is therefore proper to run prospecting drifts in the fissures, although they seldom contain much ore. As a general rule, drifting in the fissures is not costly. Mining and mucking cost from $2.50 to $4 per foot, and very little timber is required. There are instances, as in the Daly fissure in the Daly-Judge mine, where the expense of keeping drifts open in the fissure is so great that it has proved economical to make the drifts in the foot-wall rock and run crosscuts into the fissure at short intervals. In the Park City mines it is not easy to determine beforehand the best method for extracting the ore from a newly discovered ore shoot in the bedded deposits. While we may get one dimension from the drift run in the fissure, that will not give us a correct idea as to the other dimensions of the orebody. The fissures here referred to have a N. 35° E.

Jan 2, 1915

By J. Ellzey Hayden, Lucien Eaton

The Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-conerete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 1, 1922

By James Humes

The active mines in the Park City district at the present time are the Silver King Coalition, Daly-Judge, Daly West, and Silver King Consolidated. Several other companies, such as the Daly, American Flag, Ontario, etc., are doing considerable development work. In the Silver King Coalition mines the ore is a replacement of a dark siliceous limestone bed, varying in .thickness from 18 in. to several feet. In places the ore has reached a thickness of 25 ft. This limestone bed lies within 100 ft. of the underlying Weber quartzite. There are other lime beds, similar in appearance to this one, in the Park City formation, which is approximately 700 ft. thick; but not one of them has been found to contain any traces of ore. Directly under and in contact with the ore-bearing bed is another, composed of gray lime well studded with dark concretionary nodules; and this one is an unfailing indication of the proximity of the ore-bearing bed. These ore deposits make out from or have connection with some one of the ore-bearing fissures, which were undoubtedly the channels for the circulation of mineral-bearing solutions. It is therefore proper to run prospecting drifts in the fissures, although they seldom contain much ore. As a general rule, drifting in the fissures is not costly. Mining and mucking cost from $2.50 to $4 per foot, and very little timber is required. There are instances, as in the Daly fissure in the Daly-Judge mine, where the expense of keeping drifts open in the fissure is so great that it has proved economical to make the drifts in the foot-wall rock and run crosscuts into the fissure at short intervals. In the Park City mines it is not easy to determine beforehand the best method fir extracting the ore from a newly discovered ore shoot in the bedded deposits. While we may get one dimension from the drift run in the fissure, that will not give us a correct idea as to the other dimensions of the orebody. The fissures here referred to have a N. 35" E.

Jan 1, 1915

By F. J. Tuck

THE Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾ -in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3 5/8 in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1 ½ -in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A 3/4-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1938

By Everett Carpenter

THE average daily production of crude oil-in Kansas a1 the beginning of the year was about 71,000 1 bbl. and, at its close, 82,000 bbl.-an increase of 11,000 bbl. per day. The total production for the state during the year was about 28,250,000 bbl., or an average of practically 77,500 bbl. per day for the year. This increase in the production was the result of the discovery of several new pools of high-grade oil. COWLEY AND SUMNER COUNTIES One of the principal factors in bringing the production of the. state back to its former level was the newly discovered pools in western Cowley County. During December, 1923, the Waite Phillips Co. completed its Johnson No. 1 in Sec. 20, T. 33 S., R. 3 E., which opened up the Rainbow pool about 12 miles southwest of Winfield. In this pool, the production comes from the Burbank sand, locally called the "Rainbow," found at a depth of 3200 ft. The sand varies in thickness from 25 to 40 ft. in the seventeen wells completed during the year, and the initial productions ranged from 300 to 3000 bbl. per day of 40° Be. oil. The Rainbow pool is purely a wildcat discovery, for no. rocks suitable for the use of the geologist are present. To determine the geologic conditions, the larger companies core-drilled the Rainbow area immediately after the discovery. The Marland Refining, Co., drilling on the Graham farm in Sec. 9, T. 33, R. 3, failed to find the Burbank sand and continued to the Siliceous lime, often erroneously called the Wilcox, at 3505 ft., where a well with an initial production of 900 bbl. of 40 Be. oil was obtained. In the development following this discovery, 4 additional wells were completed, 3 of which encountered pay sand at 2500 ft., the initial productions each being about 200 barrels. Judging by the sands already proved and the area indicated as probably oil bearing by the development to date, these pools have a very promising outlook for the future. It is not unlikely that a field second only to El Dorado may have been opened.

Jan 3, 1925

By V. R. Garfias, C. O. Isakson

The production of petroleum in Mexico during 1930 was approximately 39,600,000 bbl., or 5,188,000 bbl. less than in 1929. The decline which has continued for the last eight years, will place Mexico in fifth or sixth rank as an oil-producing country. The production of the northern and southern fields near Tampico declined over 5,250,000 bbl., while that of the fields in the Isthmus of Tehuantepec moderately increased. The wildcat operations which have been conducted for some years near the international border along a 290-mile belt, extending roughly 170 miles northwest and 120 miles southeast from Laredo, Texas, have so far met with little encouragement, although the oil possibilities of the region warrant the belief that commercially productive fields will be discovered eventually. An interesting development during the year was the starting of construction of the oil pipe line from Palma Sola in the South Fields near sea level—over Sierra Madre at 8660 ft.—to Atzcapotzalco, a suburb of Mexico City at an elevation of 7350 ft. This line, about 146 miles long, has a diameter of 10 in. and an estimated daily capacity of 10,000 bbl., and with its terminal refinery at Mexico City will form a transporting and refining unit which should materially affect the distribution and marketing of refined products in the Republic. Development During the past year 148 wells were drilled, as compared with 214 in 1929 and 371 in 1928, the percentage of producers being 49 as against 47 in 1929. With the exception of one well in San Isidro, at the extreme southern end of the Golden Lane, the Jardln Paso Real area was the only sector of the old fields where new development could be considered as successful, all other producers brought in during the year being drilled in nearly exhausted pools to be operated as ('strippers." Northern Fields A total of 71 wells were drilled in the northern fields, of which 22 were producers; one well in Ebano was estimated at 5000 bbl. per day, while the general average of all producers was less than 300 bbl. Results

Jan 1, 1931

By G. B. Pryde, R. M. Magraw

In laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the rise, and rooms turned at right angles to these entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut. in rooms and the back entry of the level above. All entries, rooms, and entry-and-room crosscuts should be driven .on sights and room crosscuts should be driven at, right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire. Where economic conditions permit, it is preferable to follow the retreating panel system of mining. In the case of coal that outcrops, and even in cases where no outcrop is exposed, it is preferable to commence pillar extracting on the high side of the mine. Where the retreating

Jan 1, 1922

By W. F. Netzeband

THE zinc-lead mines of the Eagle-Picher Lead Co. are situated in the Tri-state district of Oklahoma-Missouri-Kansas. The company is operating, at the present time, seven mines in the brecciated deposits of the Picher, Okla., camp; two in the water-course ground of the Treece, Kans., camp; two in the open, boulder ground of the Crestline, Kans., camp; and one in the sheet ground of the Pierce City, Mo., camp. The accompanying map (Fig. 1) shows the relation of the rich narrow runs to the other ore-bodies of the district. The runs are designated by cross-hatching so as to distinguish them from narrow drifts that have been driven as prospect drifts or haulage drifts. Figs. 2, 3 and 4 are cross-sections showing the type of formation encountered in the operation of the drills. The Picher camp is in the brecciated type of deposit with some water-course ground encountered, usually near the edge of the deposit. These deposits are flat and fairly uniform so that they can be mined systematically. However, scattered between these deposits are narrow runs that are usually very rich. Up to the present time, most of the prospecting has been done from the surface with churn drills, supplemented with some prospect drifts in the ground, once the mine is opened up. Prospect drifts are expensive, do not give much information except the presence or absence of ore and are therefore not used to any great extent. In the early days of the camp only the larger deposits were found and mined, with an occasional narrow run which was drilled out more or less by sheer luck. Later, more of these narrow rich runs were found and mined, until today many of the properties that were formerly considered worked out are being leased and re-drilled. It is very evident that many of these narrow runs, which are often only 20 ft. wide, can easily be missed by drilling from the surface unless very close drilling is practiced. This, of course, becomes very expensive as there are from 150 to 250 ft. of

Jan 11, 1926

By E. S. Bardwell, Roy H. Miller

During the period extending from May, 1922, to September, 1923, the copper-refining furnaces of the Great Falls Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont., were operated exclusively with pulverized coal as fuel. The installation was made first as an experiment. It proved successful from the start and was abandoned solely because fuel oil from the Sunburst field became available at a price sufficiently low to be more desirable from an economic standpoint. The equipment required for pulverized coal has, however, been kept intact and is available for immediate use should the oil supply fail. Inasmuch as pulverized coal had been used on two large reverbera-tory smelting furnaces and was, at the time we were considering its application-to the copper-refining furnaces, being used on the Wedge furnaces roasting zinc concentrate for the electrolytic zinc plant, we were equipped with a coal-pulverizing plant of ample capacity to supply pulverized coal for the furnace refinery. The only problem was to devise suitable means for transporting pulverized coal from the pulverizer plant, located in the smelter building, to the refinery about 3000 ft. distant and about 150 ft. above the level of the pulverizer plant. When studying this installation, it should be borne in mind that the layout represents an adaptation suited to the existing conditions at this particular plant. The installation was entirely satisfactory and uniformly dependable but might be modified to advantage from an operating point of view if an entirely new installation were being planned. Fuel Supply The use of the local coals, high in ash and sulfur, was abandoned some time before coal-dust firing was attempted. Local coals from the Great Falls field carrying an average of 4 per cent. sulfur and 22 per cent, ash were used with fair success in the small furnaces in use prior to 1916. In the 250-ton furnaces, however, the time lost in grating and removing clinker from the fireboxes, as well as the difficulties incident to the high-sulfur content of the fuel, became serious and recourse was had to the

Jan 1, 1927

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By David Donoghue

Efforts made in the year 1930 and in previous years restricted production in most of the fields of Texas to a point that was satisfactory, at the beginning of 1931, to the majority of producers and buyers. In the Panhandle, North Texas and West Central Texas districts, a few operators with refinery affiliations or contracts either ignored, or by virtue of injunction suits, did not comply with the Railroad Commission's orders, and there was some oil sold at less than posted prices, which, with the Oklahoma City difficulties, caused the first general price reduction. More could have been done perhaps to help the situation on the Gulf Coast and in the Laredo district, but natural advantages are not readily surrendered. East Texas Proration troubles in 1930 were insignificant when compared with those of 1931. In January, 1931, efforts were begun to convince the producers and citizens of East Texas of the necessity of curtailment. Opposition quickly developed and meetings were held in the towns of the region and proration denounced vigorously. Notwithstanding a strenuous campaign for additional legislation waged by many producers, the regular session of the State Legislature refused to strengthen the conservation laws and passed only the Marginal Well Bill, designed to prevent the Commission from prorating small wells. The Railroad Commission held a heated hearing on East Texas in the latter part of March. During April the Commission issued three orders based on the Yates plan for the proration of the East Texas field. Each succeeding order raised the allowable for the field. In June the opposition held more mass meetings at which a plan based on acreage was endorsed. Apparently on the theory that any plan was better than none, the Commission issued an order on July 2 embodying some of the features of the proposed plan, limiting production to 250,000 bbl. per day, and dividing the producing area into 20-acre units participating equally in the outlet. Owing to the bringing in of many wells and the many violators of the Commission's orders, production increased to such an extent that prices went as low as 5c per barrel.

Jan 1, 1932

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923