Search Documents

Jan 3, 1950

By W. E. Keck, Paul Jasberg

THE flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of beneficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.-For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.-The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Witherbee- Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into -65 + 200 and -200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The -200-mesh material was rejected to eliminate possible introduction of error into flotation This paper describes a part of a general investigation into the flotation of Michigan's potential iron ores. A comprehensive discussion of the status of these ores and of the reasons for research on their Rotation beneficiation is available in mimeographed form on application to the Michigan allege of Mining and Technology, Houghton, Michigan. Manuscript received at the office of the Institute Nov. 12, 1936. Printfed without author's corrections. Subject to revision.

Jan 1, 1937

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By G. D. Van Ardsdale, A. W. Hudson

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By Alwyn Birchmore Cox, Ian William Wark

Sodium sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators1 claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1939

By M. King Hubert

The growth of human knowledge is an evolutionary process. Historically our separate sciences came into existence as people became interested in various apparently unrelated domains of phenomena, and in this manner we acquired the sciences of physics, chemistry, astronomy, biology and geology. As various of these sciences became established, cognizance of them came to be taken by the universities and in this manner there arose the traditional departments of physics, astronomy, chemistry, biology and geology of our American universities. As there was no particular rationality in the boundaries separating the various sciences, in the university departments the jurisdiction of each has assumed quite arbitrary limits. In the domain of earth phenomena the first science to grow up was that of geology, which arose originally from the activities of the collectors of rocks, minerals and fossils. Thus geology evolved as a descriptive science dealing with directly observable terrestrial phenomena for which elementary rational explanations were offered. The traditional treatment of phenomena by the science of geology has rarely been with more than an elementary regard for the fact that these phenomena were also phenomena of physics and chemistry. Since the latter part of the nineteenth century, a new approach to terrestrial phenomena has been emerging and becoming of so great a significance that it can no longer be ignored. This approach has been made by people trained primarily in the sciences of physics and chemistry, who have investigated terrestrial phenomena as constituting phenomena of their respective sciences. In this manner we have acquired the so-called "borderland sciences" of geophysics, the physics of the earth, and of geochemistry, the chemistry of the earth. Neither of these fields is new, having arisen chiefly at the hands of European investigators during the latter part of the nineteenth century. The European universities have long since given official recognition at least to geophysics, by the establishment of departments or institutes of geophysics, which are on a par with the university departments of the other sciences.

Jan 1, 1940

By C. S. Allen

With increased coal production and mechanization of coal mines many transportation problems arise. The main objective is to bring the coal to the tipple or dump it as quickly as possible. Larger and faster haulage locomotives or two locomotives connected in tandem have been adopted to solve the problem. Motor equipment, gears and control systems of locomotives to be placed on these hauls are carefully studied to meet these requirements, by an analysis of motor characteristic curves with the corresponding tractive effort curves, in order to determine the correct load for maximum efficiency and to determine the approximate schedule. Control equipment is usually considered to be the controller and resistance. Sometimes accelerating curves are calculated in order to obtain smooth starting in the least possible time without slipping the wheels. Train control is very important, but why limit this to acceleration ? Deceleratien-or-retardation of the locomotive is a part of the train control and should be given as much consideration as the control for acceleration. Types or Braking Common braking systems for mine locomotives utilize screw-type mechanical brakes, dynamic braking and the air brake. For gathering and haulage locomotives, the srrew-type mechanical brake is regarded as standard. A brake of this kind cannot be applied without much effort and lapse of time. Motormen, like other people, follow the path of least resistance, and therefore have their brakes ready for instant application—which means that the shoes are virtually dragging. Even then, a motorman bucks and plugs the motors to gain time and avoid as much physical effort as possible. "Bucking of motors" consists in turning the reverse cylinder of the controller to parallel position corresponding to the opposite direction of travel while the locomotive is in motion, without applying power from an external source. When this occurs, both motors tend to act as series generators, because the armatures are revolving and there is residual magnetism in the field circuit. Owing to slight differences in motor manufacture, one of these will generate a slightly higher potential and will overcome the generated voltage of the second and tend to drive it as a motor in the reverse Direction.-This action retards the locomotive but is very severe on the segments of the reverse cylinder and on the motor commutators. "Plugging motors" is the application of power to the motors corresponding to the opposite direction of travel. In order to "plug" the motors it is necessary first to "buck,, them (which reverses the connections to the motors) and then to apply power. Theoretically, this should be done only in an emergency, but locomotives in mine service are frequently thus treated., Dynamic braking is retardation of the locomotive by the motors acting as generators, which take no power from the line.

Jan 1, 1942

By H. F. Yancey, M. R. Geer, Franklin T. Davis

Coke with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning, An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. Previous Work Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,' and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.'

Jan 1, 1944

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By Carleton C. Long, George F. Weaton

Two years ago the general features of the St. Joseph Lead Company's zine-smelting process were described.' At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtowlz smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the company's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; SiO², 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the coacentrate to a calcine of average conlposition (first 10 months of 1938): Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; SiO², 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07'; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sulphuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in, by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO² to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1943

By V. H. Wilhelm

Developments in California during 1942 were marked by many difficulties in operation, of which the lack of labor and material were the main factors in slowing down work. During the many years of curtailment, which has been effective since 1928, a number of estimates of the state's capacity to produce have been built up, but during the year 44 fields were 'eliminated from curtailment and valuable data were obtained as to the normal capacity of these fields to produce. Because of new discoveries and the normal decline of old fields, which is more than 15 per cent per year, it is estimated that the sustained capacity of the state for a 5-year period is not more than 500,000 bbl. per day. Decline in the rate of production was greatest in the fields in the Los Angeles Basin district. These fields have been produced nearly at capacity for many years and had no reserve of shut-in production. The San Joaquin Valley and Coastal districts have responded well to the increased allotments assigned to them by the Petroleum Administrator for War. All heavy oil fields in the state are on full production, except in the Coastal district, where transportation is the limiting factor. Although approximately 2500 more wells are on production in the state than there were in 1941, the supply of heavy crude has not yet reached the demand. A summary of statistics for 1941 and 1942 is given in the following table. Production in California for 1942 was 680,000 bbl. a day as against 631,000 bbl. a day for 1941, an increase of 7.8 per cent. The present maximum efficient rate has been estimated at 808,000 bbl. per day. This indicates that in the 15 restricted fields of the state there is only an additional 83,000 bbl. per day of light oil available. Drilling Activity Drilling activity during the year was equivalent to but 70 per cent of normal. Although shortages of equipment and labor were in part responsible for the reduced drilling activity, the main reasons were the lack of proved locations due to a cycle of very few new discoveries and the restrictions of Conservation Order M-68. For the first six months of the year, 300 new oil wells were completed, which were equally divided as to the number of light and heavy oil producers. But, for the last six months of the year, it is

Jan 1, 1943

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

THE CHAIRMAN (DR. A. R. LEDOUX).-If there ever was a question in the mind of anybody as to whether there are some mining engineers, I think if they would look in the door tonight they would decide there are. We meet here tonight not only to enjoy a smoke and other incidentals which are permitted us in these days, but with a more serious thought in our minds, because that flag, with its 540 stars, only begins to show the number of our membership that are serving the country. We are thinking of them, and when we consider how many of those men are also citizens of one or another of our allied countries, we can imagine that many are tonight thinking of us and perhaps have received, even at the front, notices of our annual meeting and are wondering what we are doing tonight; so our thought this evening will be going out to them, going out to those of our number who are serving in the khaki or in the blue, or in other activities denied to some of us for one reason or another; but, gentlemen, there is one thing we will do now, we will rise and sing together r the Star Spangled Banner. Gentlemen, not only are American citizens here tonight, not only representatives of our country on the Speakers' platform, but. there are representatives of our Allies, and we are going to have the privilege of listening to one or two of the latter, a citizen of the great British Empire and a citizen of France. We will first have the pleasure of hearing Capt. Hodder-Williams. He has been loaned to us to take charge of training Columbia University students, after two years or more in the trenches, and lie carries with him the only German thing in this room, a German bullet in his shoulder. That has not affected either his spirit or his

Jan 4, 1918

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By Charles Brush

THE general subject of accurate pyrometry, its great development in recent years, and the importance of its application in arts and manufactures is so ably treated in other papers that this paper will bee confined to a resume of some research work on certain temperature effects in carbon and other steels, some of which appear to, be new. The results of these researches are embodied in several papers presented to' various scientific societies during the last few years, most of them under the general title of Spontaneous Generation of Heat in Recently Hardened Steel.1 Several years ago, when studying the behavior, tinder certain conditions, of specimens of hardened tool steel, I observed that they all spontaneously generated a small quantity of heat, the rate of generation diminishing from day to day for several weeks before generation became imperceptible in the sensitive calorimeter used. In each case the steel had been hardened only a few days prior to its use. It seemed highly probable that the generation of heat was associated with some sort of "seasoning" or incipient annealing process, perhaps accompanied by slight changes of volume, and that it would be most rapid immediately after hardening. I subsequently investigated this curious phenomenon more fully. Twelve ½ in. round bars of tool steel, 5 in. long and with machined surfaces, were hardened by heating to high cherry red in a reducing atmosphere of a gas furnace and quenched in cold water. The bars then had a thin strongly adhering coating of black oxide. They were next stirred in a large quantity of water at room temperature, to acquire that temperature, wiped dry, and oiled with heavy, neutral mineral oil to prevent generation of heat by further surface oxidation, wiped free of excess of oil and placed in the copper cylinder of a heat-insulated box.

Jan 9, 1919

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By D. L. Murphy

As the world's demand for iron ore increases and available sources are depleted, increasing attention will be centered on deposits in the Quebec and Labrador portions of the Labrador Trough. Improvements in the beneficiation of low grade iron ore stimulate exploration for deposits amenable to concentration. This study is centered on the Mt. Wright-Lake Carheil area, lying between Wabush Lake and Mt. Reed in Quebec. Described in detail are the general lithology, structural and economic geology, and mineralogy of the iron-formation. The iron ore province of Quebec and Baffin Island extends from the southern shore of Baffin Island southeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands. (See Fig. 1.) Future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. At present, only the deposits near Knob Lake and Lake Jeannine (Mt. Reed) have been brought into production although in the near future several other properties including those at Wabush Lake will commence operations. Within the next decade or so, as the world's demand for iron ore increases and available sources are depleted, this region will undoubtedly become a major mining district. Initial reports of iron-rich rocks in Labrador date back to the investigations undertaken by A. P. Low near the turn of the century. During the ensuing years the country was prospected chiefly for precious and nonferrous base metals because of its inaccessibility and the low tenor of the iron ore. In 1945 an evaluation of the direct shipping ores near Knob Lake indicated that sufficient reserves were present to justify the enormous capital expenditure required to bring the deposits into production. Initial open-pit mining began in 1954 following the construction of a townsite, a 360-mile long railway to Seven Islands, and an elaborate loading dock. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. The Mt. Wright-Lake Carheil area, bounded by longitudes 66O45' and 67 30' west and latitudes 52 30' and 52 45' north, is a nearly rectangular tract of slightly less than 500 sq miles. It is in Saguenay County, 174 miles north-northwest of Seven Islands (see Fig. 1). Except for the periods of the spring breakup and the fall freeze up, the area is readily accessible by air.

Jan 1, 1962

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976