Search Documents

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By Charles Barrett

SINCE 1925, when the preferred orientations in compressed aluminum were first determined1, 2 the orientations have been described as a fiber texture in which a face diagonal, [110], of the face-centered cubic lattice is parallel to the compression axis. Subsequent experiments have seemed to confirm this texture,3-5 and a number of theories (recently summarized in references 6 and 7) have been proposed to explain it and to relate it to the behavior of single crystals during compression. 3,8-11 The experiments reported in this paper prove that the orientations are not adequately described as quoted above-i.e., as a [110] fiber texture-although this is a first approximation to the actual texture. They also show that the texture cannot be thought of as a stable orienta-tion that is reached and maintained after a sufficient amount of deforma-tion. The actual texture, when studied in detail at successive stages of compression, indicates that a hitherto unsuspected range of orientations is present, both in the polycrystalline metal as a whole and in various individual grains in its interior, and that a state of dynamic equilibrium exists within this range. The reasons for the failure of previous theories to predict the actual texture become obvious when the heterogeneous nature of the flow is considered. In addition to the deformation texture, the manner of its develop-ment, and its theory, this paper presents data on the following related subjects: the identity of strain markings in aluminum; the orientation changes in aluminum single crystals during compression and a com-parison of these with the conditions in individual grains of a polycrystal-line specimen; the origin of asterism in deformed single crystals, which heretofore has been regarded as a distortion localized at the surfaces of slip planes; and the relation of plastic strain in individual grains in an aggregate to the strain of the whole.

Jan 1, 1939

By Thomas Haight Leggett

I.—The Deep-Level Shafts. The gold-deposits of the Witwatersrand (Anglice, " White Waters' Range ") are, as is well-known, more or less parallel and tilted sedimentary beds of quartz-pebble conglomerate impregnated with gold. These beds, however, are locally called "reefs"—a term equivalent in signification to the American "ledge"—and, like the latter, usually applied to lodes, though covering in practical usage all deposits of tabular form. The first developments of the reefs of the Rand were naturally made along their outcrops. Since the mining law of the Transvaal does not confer upon locators the "extralateral right," the property of each locator upon the outcrop or apex ends with the vertical planes drawn through the boundaries of the claim. Consequently those portions of the reefs which lie "on the dip," beyond these boundaries, are separately acquired by locating new surface-claims, and are usually to be mined only by means of vertical shafts, reaching the reefs at considerable depths. The term "deep-level properties " is given to such claims on the dip, and the " deep-level shafts " are the vertical shafts sunk in the hanging-wall of the Witwatersrand reefs, in contradistinction to the incline-shafts almost universally employed on the outcrop-properties. Number and Distribution.—The accompanying diagram, Plate I., shows the number and depth of these deeplevel shafts, completed or under process of sinking, up to January 1, 1900. A number of shafts already located upon new deep-level properties, but upon which no work has yet been done, are not included in this diagram.* Vertical shafts sunk upon outcrop-

Jan 1, 1901

By D. J. McAdam

IN a recent survey of the literature, the author has found evidence incompatible with prevalent views regarding the technical cohesive strength and yield strength of metals. Some of the evidence regarding the technical cohesive strength was presented in a previous paper,21 and views were presented that are believed to be in better accord with the evidence. In that paper, it was shown that the technical cohesion limit (contrary to prevalent views) varies with the combination of principal stresses,† and that the influence of plastic deformation on the technical cohesive strength is not in accordance with prevalent views. In this paper, consideration will be given to both the technical cohesion limit and the yield stress as affected by the combination of principal stresses. Evidence will be presented that the variations of the yield stress and the technical cohesion limit with the combination of principal stresses are not in accordance with prevalent views. Consideration will also be given to ductility and work-hardening capacity, which depend on the initial difference between the technical cohesion limit and the yield stress. By the "technical cohesion limit" is meant the mean stress at actual or potential* fracture. An example of a technical cohesion limit is the "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. The cohesion limit thus obtained for a ductile metal, however, has been greatly altered by the plastic deformation. It is important to consider the cohesion limit of the metal prior to this deformation, and the variation of the cohesive strength with plastic deformation. The relation between the cohesion limit and the corresponding flow stress† determines the ductility of a metal and the energy that it will absorb before fracture. In this paper, as in the previous paper,21 tensile stresses will be viewed as positive and compressive stresses as negative. The algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. In the previous paper, attention was confined to stress combinations with two of the principal stresses equal (with the intermediate principal stress S2 equal either to S3 or S1). In this paper, consideration will also be given to the effect of stress combinations with all three principal stresses unequal. In the earlier sections of the paper (pp. 1 to 14), attention will be confined to stress combinations with

Jan 1, 1942

By W. S. Holt, E. T. Tkac, R. A. Grange

QUANTITATIVE knowledge of the time element involved in austenite transformation in a particular steel provides a sound basis for understanding and planning heat-treatment. Such knowledge is conveniently obtained by measurement of austenite transformation as it occurs at each of a series of temperature levels. The results of these measurements usually are summarized in the form of the now familiar isothermal transformation diagram (I-T diagram, TTT diagram, or S-curve). Although a considerable number of such diagrams already have appeared in the literature, there remain many compositions of commercial importance for which no I-T diagram is available. The diagram for many such steels may be predicted from published data with sufficient accuracy for most practical purposes, but for others no satisfactory prediction can be made because the effect on austenite transformation of one or more of the important alloying elements present is not well enough known. Such a steel is Nitralloy, Type 135-Modified, which, containing about 1.25 per cent aluminum, differs from any whose I-T diagram has been published. This paper presents results of a study of the isothermal transformation behavior of a sample from a commercial heat of this aluminum-chromium-molybdenum steel, together with pertinent supplementary data including the equilibrium transformation temperatures (Ae3 and Ae1), the temperature range of martensite formation, and the end-quench hardenability. These data are directly applicable to the heat-treatment of this type of steel and are of interest in revealing some of the fundamental effects of aluminum as an alloying element in steel. MATERIAL All specimens were prepared from a 13-in. diam bar forged from a 5 by 5-in. billet from a commercial heat made in an electric arc furnace. The composition of the bar was; C, 0.41 per cent: Mn, 0.57: P, 0.016: S, 0.005: Si, 0.24: Ni, 0.17: Cr, i.57: MO, 0.36: Al, 1.26. The forged bar was normalized from 1750°F (955°C) and then tempered for one hour at 1200°F (650°C), this tempering treatment having been given to facilitate the machining of specimens. EQUILIBRIUM TRANSFORMATION TEMPERATURES In hypoeutectoid steel the minimum temperature at which austenite is completely stable, Ae3, and the maximum temperature at which austenite is completely unstable, Ae1, are of great significance in heat-treatment. Since these temperatures are dependent upon com-

Jan 1, 1946

By Raymond D. Sloan

During 1944, substantial gains were recorded in practically every phase of the petroleum industry in Oklahoma. With the spotlight of activity focused on other states during the more recent years, the production momentum that was achieved in Oklahoma through the discovery and development of such outstanding pools as Oklahoma City, Fitts. and major pools in the Seminole area during the late 1920's and early 1930's was practically spent by the end of 1943. However, with much of the industry's exploratory efforts greatly reduced in Illinois, Indiana and Kentucky, the strong demand for Mid-Continent crude and the optimism created by some discoveries in the state toward the end of 1943, Oklahoma has again become the recipient of much activity and interest, with its 1944 drilling activity, production and refinery runs to stills registering substantial gains over the preceding year. Development and Exploration Since the discovery of the West Edmond pool in April of 1943, with the substquent drilling and development boom, the scene of exploratory activity has shifted from the central. south and east portions of the state to the general trend of the . Granite Ridge, where leasillg and wild-catting were greatly activated within a wide radius of this high subsurface feature. Leasing activity, however, jumped the confines of the Granite Ridge trend and extended into all of the northwestern counties in the state. Seismograph activity at once began following and keeping pace with this shift in the leasing and exploration locale, by the concentration of a large number of seismograph crews in the area. At one time during the year,35 crews were concentrated in Oklahoma, the majority being west of the Granite Ridge and extending into the northwestern counties. To illustrate the increase in geophysical work done in the state during the year, records indicate that 377 crew months were worked in 1944, which is a 21 per cent increase over the 311.5 crew months activated in 1943. With the discovery in 1943 of several encouraging prospects and the finding of West Edmond as an incentive, drilling operations increased some 54.3 per cent, for a total of 1986 completions during the year. This is compared with a figure of 1287 for wells drilled in 1943, an increase of 699 wells. The industry, with a total of 1064 oil producers, enjoyed a success percentage of 53.6 per cent. Gas wells completed were 223, while 699 dry holes were drilled. In 1943, completions included 587 oil wells, 127 gas wells, and 573 dry holes. The number of oil producers completed during the Year was almost double the numher of wells in 1943. Of the total drilling wells completed in the state, 350, or 17.6 per cent, were wildcat operations—an increase of 5.1 per cent over the 194.3 total of 333. The wildcat success percentage was 13.4 per cent, 47 successful wells being completed for an average initial potential of 160 bbl. In the state, 23 gas wells were completed with an average initial production of

Jan 1, 1945

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By T. Prof. Ph. D. Egleston

(Read at the Amenia Meeting, October, 1877.) THE copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Hecla Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as "mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently too make it pay. The metal is so uniformly distributed through these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces,, up to many pounds. III one instance, in making an excavation for a cellar of a

Jan 1, 1878

By R. T. Walker

GROUND waters-hot or cold-containing small amounts of the more common earth acids, such as carbonic acid, silicic acid, hydrogen sulfide, sulfurous acid and sulfuric acid, have only a very limited "solvent effect on dominantly siliceous rocks, whether of igneous or sedimentary origin, but in limestone they often form extensive cavities; and such "limestone caves" are the only openings of considerable size and continuity in rock formations that do not owe their existence directly and almost wholly to dynamic action. Limestone caves such as are developing at the present time must have been formed in all past geological ages in which limestone beds existed and where suitable conditions for the development of such caves prevailed; hence it would seem a reasonable expectation that, in the course of geological history, a certain number of ancient limestone caves must have been utilized as channels for the passage of mineralizing solutions, during portions of their course, at least, and that, in consequence, orebodies must have been deposited in such caves. Such a conception is not novel; it was proposed many years ago, but its possibilities, as explaining certain types of ore deposits, have been rather lost sight of in the development of the theory of the metasomatic replacement of rocks by minerals. It is the purpose of this article to assemble evidence to show that many of the orebodies found in limestone beds have been deposited in pre-existing caves; to discuss the criteria whereby such orebodies can be distinguished from others which have been formed along fissures and fracture zones traversing limestone, by the more common method of metasomatic replacement, analogous to orebodies in other formations; and to describe certain orebodies-particularly the "ore channels" of the Tintic district, Utah-as illustrative of the principles discussed. Limestone caves may be divided into two classes: those formed by cold, descending surface waters, which emerge again at some lower elevation as cold springs; and those formed by hot, ascending waters of deep origin or circulation, which attain the surface as thermal springs. Although these two classes are similar in many respects, there are certain characteristic and inherent differences whereby they can usually be distinguished.

Jan 1, 1928

By E. B. Hughes, F. G. Norris

Oxidation is characteristic of all processes for making steel from pig iron. This thought has been aptly expressed by H. W. Graham13 in the recent Howe Memorial Lecture, "The process of steel-making consists of using iron oxide to reduce the carbon content of the pig iron to the desired level." Direct oxidation refers to the reaction that results from introducing oxygen either alone or mixed with other gases directly into the steel bath. In working a heat, oxygen in some form is added to the steel to remove the undesirable constituents as oxides. There are two general methods of supplying this oxygen to the open hearth bath. The method in which the oxygen is added as a compound such as Con or iron ore is designated an indirect method because the steel bath must first decompose the compound to attain oxygen in a usable form. The other method in which oxygen is added to the bath in the elemental or gaseous form, more or less diluted by other gases such as nitrogen, is a direct method because no decomposition is necessary before the oxygen reacts with iron to form FeO which is dissolved in the bath in a usable form. Bubble formation (at least of a macroscopic size) presents no problem in case of direct oxidation because the reacting agent (oxygen) is in the form of bubbles when entering the metal. Regardless of whether oxygen is intro- duced into the bath directly or indirectly, several reactions proceed concurrently. In the presence of the bath of molten iron, FeO is formed either by oxidation of iron by oxygen or reduction of oxides by iron. This FeO dissolved in the molten iron is the source of oxygen for the oxidation of manganese, carbon, silicon, and phosphorus if these are present. The oxidation of carbon from steel is the controlling steelmaking reaction. The introduction of oxygen into the bath, its reaction in the elimination of impurities, and its control by the use of de-oxidizing additions have been subjects of importance since steel was first made by the bessemer process. Direct oxidation is, in a sense, an application of the bessemer principle to the open hearth process. Graham13 states: "The use of oxygen or air jets introduced into the metal bath is essentially an effort to approach in the open hearth the turbulence, rapid interface reaction, and high production rate per hour that exists in the bessemer process." The general subject, "Oxygen in Steel-making," was given new life by the studies of Herty and associates starting about1925. The current interest in elemental oxygen is intimately related to the large scale production of oxygen developed during the war period. Some of the first applications were made during the early summer of 1946 at the Steel Co. of Canada using oxygen with the fuel. Such a use is of considerable interest and importance in contributing to faster heats but is not the subject of the present discussion which deals entirely with the introduction of elemental oxygen directly into the open hearth bath.

Jan 1, 1949

By F. Paredes, W. R. Holman, R. W. Crawford

The diffusion coefficient for hydrogen in the ß titanium alloy containing 13 pct V, 11 pct CY, and 3 pct A1 was measured over the temperature range 20° to 500°C. Results fit the expression: D= 1.58 x lgs exp-------==-----) cm2,sec THE diffusion coefficient for hydrogen in the metastable ß-phase titanium alloy containing 13 pct V, 11 pct Cr, and 3 pct A1 was measured as part of an investigation of the effects of hydrogen on the mechanical properties of titanium alloys. Several theories on the mechanisms of hydrogen embrittle-ment include diffusion of hydrogen at ambient temperature as an important step in the embrittling process.'-5 In hydrogen-contaminated a-ß titanium alloys, it has been postulated that the rate-controlling step may be the rate at which hydrogen diffuses from the ß phase to stress- or strain-nucleated brittle hydride platelets at the a-ß interface.' However, embrittlement of the all-ß alloy investigated in this work may proceed by a different mechanism, since this alloy can be embrittled without the formation of detectable hydride platelets.6 Troiano has suggested that in this case the mechanism of delayed failure or embrittlement is similar to that proposed for high-strength steel, i.e., repeated crack initiation caused by a decrease in bonding energy as hydrogen diffuses to points of high tri-axial stress at the root of a notch. In both types of alloy the rate of embrittlement is believed to be controlled by diffusion of hydrogen in the ß phase. Accurate hydrogen-diffusion data in the vicinity of room temperature should therefore be of some assistance in understanding the mechanisms of embrittlement in these two classes of titanium alloys. Diffusion of hydrogen in pure titanium has been studied by Wasilewski and Kehl7 at temperatures above 500°C. Their measurements on diffusion in the ß phase were extended below the ß-a transformation temperature (882°C) to approximately 600°C. This was possible because of the 8 stabilizing effect of hydrogen. No results at lower temperatures have been published and there are no data in the literature on hydrogen diffusion in the ß -phase alloy used in this program. Hydrogen diffusion in metals is generally investigated by measuring the rate of transport of hydrogen past a solid-gas interface, i.e., by absorption, permeation, or degassing-rate measurements. These methods produce accurate diffusion data when bulk diffusion is the rate-determining step in the over-all process. However, at the lower temperatures of interest in hydrogen-embrittlement studies or under conditions where surface films are present, the measured rates may be surface-controlled and the calculated diffusion coefficients will be in error. Surface effects were eliminated in the present work by using a modification of the common welded-couple technique m which two bars with uniform but different compositions are joined before the diffusion anneal." The same type of step change in the initial concentration vs distance curve was produced by electrolytically hydrogenating thin-strip specimens which had been electrically insulated over half of their length. Concentration vs distance curves were determined, after appropriate diffusion-annealing treatments, by vacuum-extraction analyses of transverse samples sheared from the strips. Diffusion coefficients were calculated by the methods of Grube.M This technique was feasible because of the large concentrations of hydrogen which can be charged into p -phase alloys without the formation of hydrides15'16 and because of the extremely low degassing rates observed when hydrogenated titanium alloys are heated in air. EXPERIMENTAL WORK The diffusion couples were cut from a 0.022-in.-thick mi ll-annealed sheet.* Strips 8 in. long by 1/2

Jan 1, 1965

By P. S. Rudman

Crystal-structure occurrences in binary phase diagrams of fifth- and sixth-period elements, zirconium through palladium and hafniun through platinum, are surveyed with the conclusion that average .group number GN is the dominant correlative. This is interpreted in terms of curves of enthalpy differences between competitiue structures that are continuous func -tions of GN. It is further reasoned that the absolute formation energies may also be continuous functions of GN and if so can be simply obtained from the regatives of the heats of sublimation of the elements. It is shown that from such a heat of formation-GN plot the heats of mixing of alloy systems can be quantitatively predicted. For example, for sixth-period alloys very large exothermic heats of mixing are predicted for systems that span GN = 6 (i.e., Hf-Pt, Ta-Os, ...). Thermodynamic data with which to test these predictions do not appear to be available. If in the latter transition (A subgroup) elements we eliminate from consideration the fourth period where magnetic terms contribute to crystal-structure stability, as shown in Table I, there is a very regular sequence of structures. Using the group number (GN) assignments of Table I, which differ from the usual assignments of 8 to the elements listed as 8 through 10, it is perhaps trivial to say that the phase occurrence is a unique function of GN. However, the interesting aspect of alloys from among these elements is that the alloy structures also appear to correlate with GN. The GN for an alloy is given as GN = SixiGNi, where xi and GNi = atomic fraction and GN of component i, respectively. It is difficult to credit anyone in particular with having discovered this correlation, so many people have implicitly or explicitly employed it in the last 10 years. However, Bloom and Grant' in their correlation of s-phase occurrence with total number of d + s electrons were certainly one of the first to appreciate the correlation and Hume -Rothery2 appears to be responsible for the use of average GN as defined above. Only in the last few years have the phase diagrams of enough alloy systems been determined for this correlation to be surveyed with any degree of completeness. We shall here, in an abbreviated format, summarize the available phase-diagram literature and discuss some consequences of the GN correlation. BINARY DIAGRAM SURVEY In Figs. 1 to 3 the phase occurrences are summarized. In Fig. 4 the occurrence limits for the more common structures are summarized. That the GN of an alloy falls within the occurrence limits of a particular structure is a necessary but not a sufficient condition for the appearance of that structure. The preceding figures certainly illustrate that GN is a dominant correlative for structures of these elements. Many of the diagrams have complications, with ordering and other phase changes occurring in intermediate phases, that cannot be clearly accommodated in such a schematic survey and have hence been left out. Such omissions cannot, however, negate the GN correlations discussed here. Relative atomic size is also an important crystal-structure determinant and since atomic size varies quite regularly with GN for these elements it is possible that the apparent GN correlation is basically a size correlation. In Fig. 5 relative size occurrence limits are given for intermediate phases and extended terminal solutions. The relative volume, ?v/(v) - 2(vA - vB)/(vA + uB), has been taken as the measure

Jan 1, 1968

By F. I. Stalkup

Vapor-liquid phase equilibrium experiments have been conducted in a static equilibrium cell on mixtures of a light, 45 API stock- tank gravity reservoir fluid and a rich hydrocarbon gas containing approximately 55 mole per cent of intermediate hydrocarbons. Both apressure-vs-composition study of the gas and a simulated reservoir fluid, and a multiple-batch contact simulation of the condensing-gas-drive oil recovery process were performed. In the latter experiments equilibrium gas and liquid compositions were analyzed. Also, conventional, "condensing-gas-drive", long-tube displacement experiments of the reservoir fluid and gases of various richness were performed. The results of these experiments could not be satisfactorily interpreted by the conventional pseudo-ternary-diagram representation of multicom-ponent phase behavior. The results seem to be explained better by considering a bubble-point surface and a dew - point surface joined in a plait-point locus. Portions of the plait-point locus cannot be "seen" directly by the rich hydrocarbon gas because of curvature of the dew-point surface. In such a system, continuous injection of the rich gas over stationary reservoir fluid might form a zone of contiguously miscible compositions from pure rich gas to pure reservoir fluid by: (1) saturating the reservoir fluid with injected gas to the bubble-point surface; (2) creating by mass transfer with fresh injected gas a path of contiguously miscible compositions along the bubble - point surface to the plait-point locus; and (3) creating by mass transfer with additional injected gas a path of gas compositions along the dew-point surface up to the point where direct miscibility results between dew-point fluid and the injected rich gas. INTRODUCTION The use of the pseudo-ternary-phase diagram to illustrate miscible displacement phase behavior has been discussed by several authors.5,7 Such a representation of phase behavior is not rigorous, but the ternary diagram nevertheless gives a qualitative picture of what actually occurs in a miscible displacement process. Fig. 1 is a typical illustration of miscible displacement phase behavior by a ternary diagram. The multicomponent hydrocarbon system is divided into three pseudo-components: a light fraction containing methane and nitrogen, an intermediate fraction containing ethane through hexanes plus carbon dioxide, and a heavy fraction containing heptane and heavier components. A two-phase region is bounded by a dew-point curve and a bubble-point curve, which are joined at the critical point. The concept deduced from such a representation for miscible displacement by a condensing-gas-drive process is as follows: a rich gas G, which lies to the right of the limiting tie line through the critical point C, is injected into the reservoir and contacts reservoir fluid L, saturating the reservoir fluid to give bubble-point fluid L1 and equilibrium dew-point gas GI. Continued injection of rich gas changes the composition of the saturated liquid L1 through a series of liquid compositions lying along the bubble-point curve, until the critical composition C is reached, at which point direct miscibility with the rich gas is achieved. Some equilibrium gas with compositions lying along the dew-point curve from G1 to C is also formed in this process. Thus, continuous injection of rich gas forms a

Jan 1, 1966

CONTENTS PAGE PEIRCE, CARL-Making Rimmed Steel. Discussed by L. F. Reinartz. H. D. Hibbard, C. L. Kinney, Jr., A. H. Woodward, V. B. Buck, A. L. Feild, J. V. W. Reynders 1 SCHROEDER, F. W., and LARSEN, B. M.-Progress Report of the Effect of the Open-hearth Process on Refractories. Discussed by D. A. Lyon 12 KEATS, J. L., and HERTY, C. H.-Elimination of Metalloids in the Basic Open-hearth Process. Discussed by J. V. W. Reynders 14 Making Rimmed Steel Discussion of paper by CARL PEIRCE, presented at the New York fleeting and issued, as Paper No. 1563-C, with MINING AND METALLURGY, March, 1926. L. F. REINARTZ, Middletown, Ohio.-Mr. Carl Peirce has presented a valuable paper on a subject that has been very widely discussed in recent years, especially since the demand for high finish, deep drawing and other grades of sheet steel in the lower carbon ranges has become an important factor in the steel business. Steel of this analysis has been produced for many years, but the product for which it was made did not require the extra care in the steel plant that it does today. It must now be worked down into thin sheets for special purposes and undergo many severe finishing processes both in the steel mill and in the fabricating plants. Mr. Peirce's paper has outlined in a concise and logical manner the steps which must be taken in manufacturing such steels. The secret of successs is attention to details of well known steel practices. I agree with him that quality steels of this class cannot normally be made out of inferior raw materials. Scrap should be clean and if possible not too variable in analysis. Galvanized scrap or babbit are particularly objectionable. Scrap should be in such physical condition that undue delays are not encountered in charging the furnace. Limestone should preferably contain over 95 per cent. available calcium carbonate, and be free from clay or other foreign substances. Almost universal practice shows that 10 per cent. limestone is required for proper slag volumes to protect the metal from over oxidation. The use of 8 per cent. limestone makes the operation less fool-proof.

Jan 4, 1926

By J. F. Held

In a study of the influence of cold rolling on mechani cal properties of steel, it was found that the specific rolling procedure influenced crystallographic orientation. Properties developed by several rolling modes were determined and related to crystallographic orientation. Sanzples were cold-rolled various amounts on a laboratory mill. When palm oil was used as a lubricant, the crystallographic orientation was homogeneous throughout the thickness of the samples. Other samples were rolled without lubrication. Variations in intensity of the recrystallization texture components persisted throughout more than 50 pct of the volume of these samples. When the average plastic strain ratio, which is dependent upon crystallogvaphic orientation, was plotted as a function of percent reduction, a maximum was found at 40 pct in the samples which contained the observed texture variation. No maximum was found for the samples with the homogeneous texture distribution. Other mechanical properties, such as tensile strength and yield strength, were not influenced by the variation in crystallopaphic orientation. MECHANICAL properties of steel sheets depend, in general, upon the structural properties of the steel. For example, the Petch equation describes the relationship between yield strength and grain size. Other properties, such as hardness, vary with chemical composition. The plastic strain ratio, or R value, has been found to be dependent upon crystallographic orientation . In the course of investigating the effect of cold rolling on mechanical properties, it was found that a previously reported relationship between percent cold reduction and R value was not always observed. Published data had shown that the optimum cold reduction for best R values is 70 pct for aluminum killed steel.' However, by altering the rolling conditions, the optimum reduction can be shifted to much lower values, or it can be moved to very high values. This paper describes the rolling conditions that lead to shifting of the optimum cold reduction. The effect of rolling conditions on the various structure parameters and the resulting mechanical properties are evaluated. EXPERIMENTAL PROCEDURE Samples of three low-carbon aluminum killed steels were cold-rolled various amounts on a 9-in.-diam 2-high laboratory mill. Hot-mill thermal practice and steel chemistries are listed in Table I. Steel A was rolled with palm oil lubrication and heavy reductions on each pass; i.e., a total reduction of 75 pct was ac- complished with a maximum of five passes. Steel B was rolled without lubrication, and light reductions were given on each pass. After approximately 75 pct reduction, it was necessary to use a small amount of light oil to achieve any additional reduction in thickness. Following cold reduction, the samples were box-annealed at 1300°F for 10 hr. The heating rate between 800" and 1300°F was 50°F per hr, and the cooling rate following the soak period was 50°F per hr. Tensile specimens were machined from the annealed material and these were used to measure yield strength, tensile strength, and the plastic strain ratio (R value). Recrystallization textures were determined by an inverse pole figure technique.*'3 Integrated intensities of the (110), (002), (112), and (222) reflections were recorded for those planes lying parallel to the sheet surface. Examinations were made on both surfaces of each sample, and also at various levels beneath each surface to approximately 0.010 in. depth by etching techniques. RESULTS R Values. The R values obtained in steels A and B are shown as a function of percent cold reduction in Fig. 1. No optimum cold reduction was observed in steel A, rolled with palm oil lubrication. It is likely, however, that an optimum reduction would have occurred had higher reductions than 88 pct been employed. The optimum reduction in steel B occurred at 40 pct. The behavior in both of these steels is quite

Jan 1, 1968

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By F. V. Lenel

INTRODUCTION Two years ago in Chicago a seminar was held on the theory of sintering of pure metal powders As an introduction to this seminar Dr Rhines1 gave an excellent survey of the literature on this subject His method of presentation was to summarize the experimental observations on sintering and from them to develop a composite theory of sintering in which he combined all the important contributions to the theory into one organic whole In contrast to the mechanism of sintering of pure metal powders, which, of course, always takes place in the solid phase, sintering in the presence of a liquid phase, cannot be treated as one unified mechanism, such as the sintering mechanism of pure metals The reason is that there are really several mechanisms depending upon the type of alloy system which is sintered and the field of its constitutional diagram in which the sintering takes place Two mechanisms have been investigated and will be reviewed in this paper In the first mechanism the liquid is present during the entire time while the compacts are at the sintering temperature In other words they are sintered between the liquidus and the solidus of the alloy System and are heterogeneous during the entire sintering cycle The second mechanism applies to alloys in which the liquid phase is formed during the sintering process, but disappears before the sintering process is completed through diffusion and formation of a solid solution These alloys are therefore homogeneous at the end of the sintering cycle This second mechanism is more complicated because of the two stages of sintering, the liquid and the solid, as they may be called It is therefore not surprising that the few detailed investigations of sintering in the presence of a liquid phase have been concerned with heterogeneous sintered alloys, namely the tungsten-nickel-copper alloys, which is the so-called "heavy alloy," and the cemented carbides The mechanism of sintering of these systems is characterized by the fact that theoretical or near theoretical density is attained during sintering, while simultaneously a distinct grain growth takes place through solution of the smallest grains of the solid phase in the liquid phase and reprecipitation on the larger grains In the first part of the survey this sintering mechanism which is called for short the heavy alloy mechanism is treated in detail In the second part of the survey experimental observations for the sintering of homogeneous sintered alloys where the liquid phase disappears before the completion of sintering are discussed Much less systematic work has been done on these alloys to which the commercially important porous bronzes and the iron-nickel-aluminum permanent magnet alloys belong Emphasis will be laid throughout this survey upon the microstructural and density changes during sintering because the sintering mechanism can usually be described directly by these changes Other

Jan 1, 1948

By E. R. Stover, J. Wulff

A tentative 870°C isothermal section, the solidus equilibria, and the solubility of Tic and graphite in the nickel solid solution have been determined with arc-cast specimens. Each of the Ni-Ti intermetallics forms two-phase fields with Tic; only Ti,Ni has a measurable solubility for carbon. A quasi-binary eutectic exists between Tic: and a titanium-rich nickel solid solution; ternary eutectics occur on either side, with TiNis or with graphite. Graphite is in equilibrium with a nickel solid solution containing a ratio of Ti/C which increases below the solidus. DURING the past decade, titanium-carbide cermets containing nickel or cobalt alloy binders have been widely studied for high-temperature and wear-resistant applications. Recent work has emphasized control of the carbide grain size and distribution2's and the thermal exparision match between the phases/ The present study was initiated to determine the phase compositions during the sintering or infiltration process, and during subsequent heating. Although the effects of additives and impurities in commercial compositions are important, it was necessary to consider first the pure ternary, Ni-Ti-C. Emphasis was placed on the nickel corner, since the nickel solid solution is the continuous phase in compositions having highest strength. Early metallographic work by Zarubin and Molkov- showed that solid solubility at either end of the section Ni-Tic is small. Edwards and Raine reported that nickel dissolves between 3 and 5 wt pct Tic at 1250° C, on the basis of microstructures of annealed, vacuum-melted powder mixtures. Although the solubility of nickel in Tic has not been measured, Tic formed by the menstruum process in liuid-iron solution contains as little as 0.06 wt pct Fe. BINARY SYSTEMS The most recent determinations of the three binary systems are summarized in Fig. 1. Titanium carbide (6) is predominant among the binary phases, and it melts above the boiling point of nickel. The Ni-C binary is based on separate liquid solubility' ) and solid solubilitylo measurements. The eutectic temperature, 1328OC, is taken from the solidus determination described below. However thermal analysis data by Morrogh and williams also show eutectic arrests in this vicinity in the absence of supercooling. The Ni-Ti binary is taken from the work of Poole

Jan 1, 1960