Search Documents

By Robert E. Cuthbertson

It is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson,= by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be corfined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. Brief History of Reagent Practice at Climax Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 19-20, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Nevertheless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1947

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,' as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By M. E. Wadsworth, J. S. Cho

The kinetics of silicate adsorption from aqueous colloidal (SO2 . nH2O) silicate sols on thoria (ThO 2) surfaces were determined at 100, 150 and 200°C in an autoclave system. The amount of chemisorbed silica on the thoria surface was determined by means of infrared spectroscopy. First order kinetics were observed in all cases with the anomalous result that the first order rate constant was found to vary with the initial amount of silica added to the system. These results have been correlated quantitatively by means of a strain model of adsorption involving two types of surface silicate bonding, both of which may be readily observed in the infrared spectrum. Initial adsorption occurs rapidly to produce one type of surface silicate followed by a slow transition to a second type of surface bonding, the latter transition representing the slow step in the adsorption process. Initial interest in silicate adsorption on thoria arose from the dispersive effect silica has on finely divided thoria in aqueous suspensions. Spaepen et al studied the equilibrium adsorption of silica on thoria and noted increased adsorption up to approximately 215°C with a notable decrease in adsorption at temperatures above 215°C. Similar results were observed by Cho and Wadsworth2 who identified two types of surface silica by infrared spectroscopy. At temperatures of 100°C and above, rapid initial adsorption occurred producing a surface species with maximum infrared absorbance at 9.4 After extended periods of time, the 9.4 species converted to a more strongly bonded surface silicate with maximum infrared absorbance at 10.3. The latter was very strongly bonded and difficult to remove by desorption in hot distilled water, while the 9.4 species could be removed more readily by similar treatment. The 9.4 and 10.3-p species were distinguishable from free unadsorbed silica which had maximum infrared absorbance at 9.1 The kinetics of the formation of the strongly chemisorbed silica (10.3) on thoria as determined by infrared examination are presented in this study. EXPERIMENTAL PROCEDURE As a source of silicate, Ludox SM (16.36% SiO2) or Ludox HS (30.25% SO2), DU Pont colloidal silica in aqueous suspensions, was added directly to a thoria slurry made up of one liter of distilled water and one gram of thoria. The thoria used was designated D-16-650 and was received from the Chemical Technology Div. of Union Carbide Nuclear Co. It was prepared by firing thorium oxalate at 650°C. The D-16 thoria had a surface area of 32.4 ± 0.6 sq m per g as determined by nitrogen adsorption.* This thoria 'Determined by Unlon Carbide Nuclear Co., ORNL. had a total adsorption capacity for silicate of approximately 19.4 mg of silica per gram of thoria.1 This amounts to approximately one SiO2 molecule for every surface thoria site. In all cases in this study.

Jan 1, 1963

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct Tho2*, and the ilmenite 561/2 pct TiO2, whereas the corresponding Travancore minerals carry 9 pct Tho, and 60 pct TiO, respectively. The Brazilian zircon is a dirty brown color (which can be removed readily) as compared with the gleaming whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be available in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources.' Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations. Substantial tonnages of rutile have been exported from Brazil. The sources of this mineral are stream placers and residual deposits over gneisses in the States of Goyaz, Minas Geraes, Ceara, etc. (Leonardos,' and Chambers". With these handicaps, Brazilian production from beach sands has been marginal, and there has been only one consistent producer. This is a company, originally French, which was called Companie de Franco-BrazilliCne, but, with the downfall of France in 1940, became Brazilian under the name Monazita e Ilmenita do Brasil ("Mibra"). This company has operated several deposits in the vicinity of Guara-pary, in the State of Espirito Santo. Its office and plant has been at Guarapary. Recently a company called, "Fomil" (Fomento Monazita-Ilmenita) started operations. This company was organized by the Foote Mineral Co. of Philadelphia, and such share as a foreign company can hold under Brazilian law has now been acquired by the Lindsay Light and Chemical Co. of Chicago. When the writer went to Brazil in the fall of 1940, he found that no general survey of the beaches had been made except for a thorough study of part of the area by Abreu.4 The paper by Miranda6 had not then been written. The federal Geological Survey and Department of Mines knew only of the existence of the deposits in Espirito Santo south of Vitoria, and had a hazy idea that others might be found north of Vitoria. One deposit in Bala was known in Rio, but the larger one at Guaratiba was not known, although a Frenchman had prospected

Jan 1, 1951

By Richard McCaffery

WHEN we began the study of blast furnace slags we limited our work at first to a study of those slags containing only lime, alumina and silica. In our paper1 on some of the results of this first work, the solubility of. sulfur in slags containing no magnesia was reported and the question of sulfur solubility and slag viscosity discussed. There has been, for a long time, a very great difference of opinion among metallurgists as to .the effect of magnesia in blast furnace slags, and the literature is full of expressions of the most contrary opinions on the subject. As a result, our next publication2 developed the constitution of slags considered as a four-component system, silica-alumina-lime-magnesia, and advanced an explanation of slag structure which accorded with the facts and with scientific theory. The present paper continues our study of the general subject of slags. As blast furnace slags are included in the silica-alumina-lime-magnesia system, which is a particular case of four-component solutions, we have determined that there are 22 components (Table 1), which may enter into the silica-alumina-lime-magnesia system and that 10 or 12 of these components may be present in blast furnace slags which are within the ordinary ranges of composition. To have a very definite conception of the behavior of these components in a slag, we have developed the theory of the cooling of a four-component solution from the liquid state to the solid and the conclusions that we obtained have been made use of in this paper. On account of the importance of the four oxides and 18 compounds which enter into the silica-alumina-lime-magnesia system, some method of calculating the percentages of the various compounds that are present in the slag when the percentages of the oxides are given, seemed very desirable and we develop a method later herein for doing this, and finally we give illustrations of

Jan 10, 1926

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.', ' Other methods employed are the drag and spiral classifiers and the hydroseparator.' These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By P. F. McIntyre

Electrolytic refining of lead was first carried out on a commercial scale at Trail, B. C., in 1903. The capacity at that time was small, and cell-changing operations were managed with chain block and monorail. Development up to 1922, utilizing crane installations and cell additions, attained a production of 100 tons per day. Successive additions from 1922 to 1926 further increased the rated capacity to 396 tons per day. Other improvements in metallurgical practice have gradually increased production, until for the year 1935 it was 448 tons per day. During the first five months of 1936, an average daily production of 504 tons was maintained without increasing the size of the plant. Lead Refinery Buildings.—The tank room and the lead-melting and casting equipment are housed in two buildings, which parallel each other and which for the greater part of their lengths are joined by a connecting aisle. All basements, walls, sumps and floors are of concrete. Where exposed to the electrolyte, the concrete has a protective coating of asphalt (220" melting point) over a coat of asphalt paint as a primer. Buildings erected before 1924 are of wood. More recent additions are made of structural steel with gunite siding. A brick building, adjoining the older section of the tank room, houses the slimes-treatment plant. The power house, containing motor generators, air compressors and rectifiers, is constructed of tile. Cell Construction.—The electrolytic cells are of reinforced concrete lined with asphalt. They are cast in pairs, the outside dimensions of a double cell being 113 in. long by 73 in. wide by 48 in. deep. The bottom is 6 in. thick and the sides, ends and center wall are 4 in. thick. A ledge 3 in. wide and 2½ in. deep is left along the top of the side walls to carry the insulators and bus bars. Reinforcing consists of ½-in. round iron rods. Cell inspection and repair work is done in conjunction with the cell-changing operations. The repair work necessary is usually confined to renewing chipped asphalt, unless a tank has been accidentally broken. Minor concrete repairs can be easily made in place. The broken concrete

Jan 1, 1937

By J. Hunter, P. M. Lyons, L. C. Aycock

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By Richard S. McCaffery, Clarence H. Lorig, Joseph F. Oesterle, Ira N. Goff, Oscar O. Fritsche

This paper is the report of an investigation to determine the relations between the viscosity, temperature and composition of that portion of the silica-alumina-lime-magnesia system(l) within which blast-furnace slags are found. The work reported in this paper was made possible by a grant of funds from Engineering Foundation. It is a part of a project, the determination of properties and structure of iron blast-furnace slags, upon which the laboratories of the University of Wisconsin have been at work for some years. Three papers have been published, which have marked the progress of the study of iron blast-furnace slags at Wisconsin. The first,(2) Desul-furizing Power of Iron Blast-furnace Slags, discussed the solubility of sulfur in slags that contained no magnesia and discussed the viscosity. The second, (3) The Constitution of Iron Blast-furnace Slags, developed the constitutions of slags in the four-component system, silica-alumina-lime-magnesia, and pointed out an explanation of slag structure. Composition of Iron Blast-furnace Slags,(l) which was the third paper, gave a method of calculating the percentages of the various compounds present in slags when the amount of oxide was given and also an interpretation of quaternary equilibrium. Illustrations were given of the mineral composition of blast-furnace slags and some applications of composition results were shown. Because of their relative ease of measurement, the viscosity-temperature relation for slags was selected as a factor which would be useful in correlating the physical properties of molten slags to furnace operation. With this in mind the viscosities of slags whose compositions are in that portion of the quaternary system, silica-alumina-lime-magnesia, in which blast-furnace slags occur, were thoroughly investigated.

Jan 1, 1932

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965

By Stephen Taber

A VEIN may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-hearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-hooks today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped 'masses should be classed as veins or as dikes. Some of

Jan 8, 1918

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By John E. Lanning

During the last decade, since most smelters have included Cottrell plants as standard equipment for the removal of dust from furnace gases, it has become apparent that smeltermen have had a new problem slowly developing. This problem has manifested itself in accelerated destruction of, or serious injury to, the masonry of flues and chimneys. The masonry either spalls, if the material is of low strength, or acquires large major cracks, either of which conditions attains such proportions that renewals or reinforcing become necessary to maintain the structure in satisfactory condition. This paper describes the failure of a large modern brick chimney to such an extent that its safety was vitally impaired; the investigation of its condition; the methods of restoring satisfactory strength to the structure; and the installation of an acidproof lining. Plant History The Clarkdale smelter of the United Verde Copper Co., which was put in operation in 1915, was primarily a blast-furnace plant. The smelter at Jerome had utilized blast furnaces exclusively, and in the design of the new (1915) plant, blast-furnace smelting evidently was considered of major importance, the smelting equipment consisting of four blast furnaces 48 in. by 26 ft. 8 in. and three reverberatories, each 19 by 101 ft. The latter, supplemented by roasters, were intended mainly for handling dust and fine ore resulting from the crushing operations. The original roasting equipment consisted of six six-hearth Wedge roasters, six more being added in 1917. All gases from blast furnaces, reverberatories, roasters and converters were conducted by means of suitable flues and dust chambers to one central chimney. This chimney, 30 ft. inside diameter by 400 ft. high, is a self-supporting steel structure, lined with 4-in. brick supported on steel shelf angles, riveted to the shell, spaced about 15 ft. vertically. The bricks were of local manufacture, not particularly hard-burned, and were laid in ordinary cement-fireclay-sand mortar. No record is available to indicate that any particular effort was made to secure an acidproof mortar. The same materials were employed in the construction of the reverberatory and roaster flues, and the roaster dust chamber. Parenthetically, it may

Jan 1, 1934

By W. A. Anderson, R. F. Mehl

RECRYSTALLIZATION of cold-worked metals has long been known to proceed by a process of nucleation and growth.1 When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.' Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrystallization is thus analyzed into its two component rates.2 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;* values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of N and G over appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913