Search Documents

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By W. M. Peirce

Commencing in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very- broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole. to pain: out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount . that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things' Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944

By Robert S. Dewey

Drilling in West Texas during 1942 was substantially less than in the previous year. In all. 1267 Wells were drilled, as compared with 2325 wells in 1941. Of these 1267 wells, 1052 oil wells, 10 gas wells and 69 dry holes were drilled in proven fields and 36 oil wells, one gas well and 99 dry holes were wildcat operations. Of the 36 wildcat wells completed as oil producers, 16 led to new field discoveries, three found new productive horizons in old fields, and 17 extended the productive limits of established fields. Where semiwildcat drilling took place along established productive trends, there was often no sharp demarcation between wildcat wells that extend field limits and normal development to fulfil lease obligations, other than the arbitrary classification of a well as a wildcat if it was drilled at a distance of 2 miles from a producing oil well. The dry hole drilled on the edge of a field may have proved a more hazardous operation than a semiwildcat drilled several miles from production but favorably located on structure. The percentage of successful wildcatting ranges from 26.5 down to 14 per cent, dependent upon the degree of inclusion of the semiwildcat operations. Irrespective of which figure was used, the West Texas area maintained its better than average exploratory position. No doubt a number of factors may have influenced the extent of the 1942 development. Among those arising from the economic dislocation attendant on the war effort, the following are worthy of note. Owing to inductions into the armed forces and shipyard competition for mechanically trained men, experienced drilling personnel was sharply reduced, thereby increasing drilling costs and well-completion hazards. Replacement labor has not met the same standard of responsibility or workmanship to which the oil industry has grown accustomed. Increased military consumption of aviation gasoline and other crude products, coupled with decreased domestic consumption of lower-octane gasoline, has stimulated the market demand for the types of sweet crude most readily processed with available refinery equipment to meet war requirements, and has depressed the market demand for the sour West Texas crudes. As a majority of the purchasers of West Texas crude normally ship a substantial portion of sour crude to the refineries on the Atlantic seaboard, the loss and diversion of tanker service between Gulf Coast and north Atlantic ports have further curtailed the market demand for this type of crude oil. As some purchasers of crude oil were able to move by pipe line their West Texas trunk-line capacity to Midwestern refining centers, they were not impelled to curtail purchases of West Texas crude. The varying ability of the purchasers of crude oil to market West Texas crude was reflected back to various fields to which they were connected, causing an unequal distribution of production as among fields and operators. The pipe-line runs from the West Texas-New Mexico area decreased from approximately 354,000 bbl. Per day in January to about 265,000 bbl. in December 1942. .Approximately 2,991,000 bbl. of West

Jan 1, 1943

By L. S. Darken

The manufacture and treatment of metals comprises operations whose effectiveness depends in large measure upon diffusion phenomena. The significance of such phenomena has, for a few simple cases, long been understood, but in more complex cases it has not been adequately recognized. This paper presents a mathematical analysis of some of the cases in which diffusion leads to the formation of a new phase within the metal, and this analysis provides a basis for interpreting quantitatively many apparently diverse experimental observations recorded in the literature, some of which are outlined in the following pages. OBservt1ons Recorded in Literature An outstanding instance is the general type of phenomenon in which diffusion of an element into an alloy is followed by a phase change, which most frequently is a reaction (precipitation) of the diffusing element with one or more components of the alloy to form a compound. Thus in certain alloys heated in contact with oxygen not only the usual oxide scale appears but, in addition, beneath the surface, a well-defined zone in which free oxide particles are dispersed with notabIe uniformity. This zone, commonly referred to as the subscale or zone of internal oxidation, is remarkable in that the visible boundary between it and the unaltered metal is usually sharp. Such a subscale, which appears to have been recognized first in oxidized copper alloys, has been described and studied by C. S. Smith,l by Rhines,2 and by Rhines, Johnson and Anderson;3 but it appears also in other alloys when they are exposed to conditions that bring about the precipitation of some compound, not necessarily an oxide. Another clear case of this same kind is the diffusion of carbon into a steel containing an element such as molybdenum, chromium, vanadium or tungsten, whose carbide is less soluble in iron than iron carbide, the result being that some part of that element is precipitated as a dispersed carbide. A similar phenomenon may occur on the welding of two alloys each of which contains one of a pair of elements that react to form a compound or a new phase of any sort. But in addition to the precipitation of a compound formed from the diffusing element, other effects may result merely from the presence of the diffusing element. For instance, if homogeneous austenite, nearly saturated with respect to carbon, is heated in contact with silicon in the absence of oxygen, one would expect to find, behind the several iron-silicon phases analogous to a scale, a zone of austenite containing dispersed carbide, because of the fact that silicon decreases the solubility of carbon in iron. As still another example, oxidation of an alloy may result in diffusion toward the surface of one or more of the constituents; for instance, during oxidation of a steel containing an element such as "copper, which is less prone to oxidation than iron, there is a notable enrichment of copper just beneath the scale-metal interface. AS an example of a yet more

Jan 1, 1942

The Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysi-cists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1946

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931

By R. S. Dean

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steel-making furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

The Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysi-cists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1946

By J. B. Reed, T. A. Read, H. Rosenthal

Although the season cracking of brass has been a subject of experimental investigation for more than thirty years, the mechanism that is responsible for this phenomenon is still obscure. While at- tempts to elucidate the stress-corrosion cracking of some alloys have been relatively successful, the principal accomplishments made in the studies of the season cracking of brass have consisted of improved techniques for the fabrication of articles of alpha brass, which reduce the danger of season-cracking failure in service. The primary purpose of the present paper is to collect the published experimental data which appear to be of importance to the development of an adequate theory of the mechanism of the season cracking of brass. Some of the possible mechanisms which have been proposed will also be discussed, together with some promising avenues of future attack on the problems. Several excellent survey papers on season cracking are available, including the recent ones by Croft and Sachs(1)2 and by Gibbs(2). The principal facts concerning season cracking, as presented in these papers, may be summarized as follows. The season cracking of alpha brass is a special type of stress-corrosion failure, which may occur in atmospheres containing ammonia, air, and water vapor. The stress causing failure may be either the

Jan 1, 1945

By W. H. Brandt

ThEre has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidcnce. Particularly noteworthy among the empirical work is that of Grossmann,12. who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.'-5 They have shown that formation of pearlite proceeds by a process of nuclea-tion and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to Hl in a small part of the gap. A method was prcsented recently1' for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eu-tectoid steel was calculated, using linear extrapolations of the ferrite and comentite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and T', the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1947

By J. H. Hollomon, L. D. Jaffe, M. R. Norton

In the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermalt‡ decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work.§ Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. Method In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1947

By S. LeFevre

, The solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covcrs briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results. Sanitation The sanitary service covers 238 tenements. The installation cost was about $22 per tenement, as follows: Privy, $15; privy box, $3; proportion of incinerator cost, $2; garbage can, $2. The operating cost is $1 per month for each tenement. In considering the installation of an ordinary village system of water supply and sewerage two difficulties were encountered: First, lack of a sufficient quantity of water; there is no stream large enough, as Mineville is situated very close to the divide between the Lake Champlain and Hudson River watersheds. A storage reservoir was tried, but the only location available, among glacial hills, would not hold water. Second, the expense of digging ditches for the distribution of water and sewer pipes is so great as to be prohibitive; Mineville is built chiefly in a valley covered in the bottom with drift, in this case a combination of boulders and hard pan. Digging in this material costs 80c. to $1 per cubic yard, and pipes must be placed 41/2 ft. down to be below frost. The houses are scattered along 4 miles of streets, the oldest having been built in the original forest 65 years ago. The newer houses have gone up a few at a time wherevcr a clear space could be found and the slopes were not too steep. This has advantages, as it separates the dwellings into

Jan 1, 1915

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

By G. A. Croes, N. Schwarz

The dimensionless groups, to which the variables that govern the displacement of oil from reservoirs by liquids can be combined, are derived. Three types of displacement are considered, viz. cold-water drive, hot-water drive and solvent injection. The derivation of the dimerzsionless groups is carried out by means of the relevant basic equations (in-spectional analysis). The resulting sets of groups are afterwards completed by means of dimensional analysis. The form of the groups is given in such a way that they can be adapted to suit the various boundary conditions that are encountered in practice. The physical meaning of the groups is discussed. They have all been brought together on a chart, from which their mutual relation and their corresporzdence to related dimensionless groups in common use in other engineering sciences can be read off. The limitations of dimensionally scaled model experiments as a useful tool for studying liquid flow in porous media, as occurring in oil reservoirs, are discussed. The use of models to study fluid mechanics has an appeal for everyone endowed with natural curiosity. What active boy has not played with ship and airplane models, or crude models of dam and drainage systems Even in the most advanced technical engineering, such models play a fundamental and indispensable role. "And yet in few departments of the physical sciences is there a wider gap between theory and practice, between scientific knowledge and the state of art, than in the use of models to study hydrodynamic phenomena." Garrett Birkhoff1 INTRODUCTION Laboratory displacement experiments are extensively used to investigate, directly or indirectly, the production behavior of petroleum reservoirs. Such experiments are representative of the reservoirs as a whole, if they are carried out with models that are "properly scaled." The performance of oil reservoirs is governed by the values of a number of variables, which can be combined to dimensionless groups. Two general methods are available for the derivation of these groups. In the first of these, dimensional analysis, combination of the variables is done essentially by trial and error. Its only premise is knowledge of the complete set of relevant variables. In the second method, inspectional analysis, the dimensional homogeneity of the equations describing the behavior of the system to be studied is used. The resulting dimensionless groups can be divided into: (a) independent (variable) groups, such as dimensionless length, time, etc.; (b) dependent groups, giving the dimensionless form of the variables, such as recovery and pressure, that can, at least in principle, be measured during an experiment; (c) similarity groups, which are independent constant groups, such as ratio of length to height of the reservoir and ratio of

Jan 1, 1957

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By J. R. Campbell

The need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. Washability Studies The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money can hardly be spent on "feed surveys') to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus. The sizes to be examined to get the picture are optional to the investigator. In modern wet washing, the range is from 4 to 0 in. Hand-picking on properly constructed belts is perhaps the standard for cleaning above these sizes. A good picture of the coal may be obtained by the following screen analysis: 3½ to 1¼ in. 1¼ to 3½ in. ½ to 5/16 in. 5/16 in. to 14 mesh 14 to 28 mesh 28 to 48 mesh and for very complete data on the fines: 48 to 100 mesh 100 to 200 mesh and through 200 mesh

Jan 1, 1930

By B. D. Smith, K. H. Coats

Experiments in which calcium chloride displaced sodium chloride from four cores showed the extent of asymmetry in the resulting effluent concentration profiles. These results provided a check on how validly the mixing process is modeled by a differential (i.e., not finite-stage) capacitance mathematical model. The effluent concentration profile from two consolidated cores exhibited considerable asymmetry, while two unconsolidated cores yielded nearly symmetrical profiles. All runs resulted in breakthrough of the 50 per cent concentration significantly before one pore volume was injected. In addition, velocity appreciably affected the effluent concentration profile from a Torpedo sandstone core. The differential capacitance model matched the data significantly better than a simple diffusion model. The capacitance model allows determination of the amount of dead-end pore space in a porous matrix and the effect of velocity on the rate of diffusion into this space. An experimental program yielding insight into the physical validity of the capacitance effect is described. INTRODUCTION Axial dispersion — the mixing accompanying the flow of miscible fluids through porous media — has been the subject of many relativeiy recent studiesl-13 and a comprehensive review of the topic has been given by Perkins and Johnston.14 This dispersion is of practical interest in studies of the miscible displacement process, fixed-bed chemical reactors, and the adsorption of solutes from a flowing stream onto the surface of a porous medium. In the latter case, the effect of dispersion must be considered when adsorption parameters are determined from the nature of concentration profiles. In general, early studies of dispersion assumed applicability of a simple diffusion equation and were concerned with correlation of the experimentallv determined "effective" diffusion coefficient with system properties over a large range of the latter. Recent have been concerned with the deviations between the asymmetrical effluent concentration profiles observed and the symmetrical ones predicted by the diffusion model. In the present study, effluent concentration profiles were obtained from consolidated and unconsolidated cores. These profiles were compared with those predicted by a differential (i.e., not finite-stage) capacitance model. Solutions to the simple diffusion model, for three sets of boundary conditions, were compared with one another and with the experimental profiles. SUMMARY OF PREVIOUS WORK The reader is referred to Perkins and johnston14 for an extensive review of studies of dispersion in porous media. Many investigators have employed the simple diffusion model characterized by Eq. 1 below: The dispersion coefficient D for unconsolidated systems is correlated by u is interstitial velocity and dp is particle diameter. Since heterogeneity of the sand pack affects the mixing, this equation is also expressed as where a is proportional to the degree of heterogeneity and is about 3.5 for random packs of unconsolidated sand.l4 Eq. 3 holds for 2 For a Do homogeneous (regular) type of packing, should be 1 or less.6 Aris and Amundson6 and Carberry and Bretton consider o to be the number of particle lengths per mixing cell in the finite-stage model. Data from consolidated cores indicate dp to be about 0.36 cm for outcrop rocks, Torpedo sandstone having a reported value of 0.17 cm.15 For v /Do less than about 2, the effect of molecular diffusion must be considered and the total dispersion coeffi-

Jan 1, 1965

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936