Search Documents

By E. H. Erwin Gartner

The Rhenish lignite deposit in the Nordrhein-Westphalia province of the German Federal Republic covers an area on the left bank of the Rhine River of about 970 sq miles (Fig. 1). Here, in the Miocene era, some 20 million years ago a lignite seam was formed and later broken, through tectonic movements into several blocks, some thrown down into depths of over 1,500 ft. This deposit consists of a single seam, in places up to 300 ft thick, but averaging about 150 ft. In a few areas, it is split into as many as five seams, separated by barren strata. It contains about 60 billion tons (2000 lb/short ton) of lignite which, however, being relatively young geologically, has, because of approximately 60% moisture, 2 to 8% ash, and low sulfur, a net calorific value of 3,340 Btu. That calorific value increases, however, with rising thickness of the cap rock. About one-third of the yearly production of 90 to 100 million tons of raw lignites is converted into briquets. Raw lignite is pulverized and dried to about 18% water content and then pressed without binder into briquets under a pressure of about 14,000 psi. The briquets are being used primarily for residential heating; their sales, however, have been declining sharply since 1963. On the other hand, the volume of raw lignite used in steam power plants has been rising steadily and amounts at present (1968) to about two-thirds of the total production. Huge steam power plants, such as Frimmersdorf, shown in Fig. 2 (which, with an installed capacity of 2,600 MW [megawatt], represents the world's largest steam power plant) with a generating capacity of up to 300 MW per unit and a total installed capacity of over 6,000 MW, contribute about 26% of the total electric power production of the German Federal Republic.

Jan 1, 1969

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By Paul M. Tyler, Oliver Bowles

The extensive employment of nonmetallic minerals antedates the use of metals, but only within the last two decades has the production of nonmetals begun actually to keep pace with the complicated activities which characterize the so-called Machine Age. The economic changes ushered in by the Industrial Revolution were reflected first in an increased demand for metals and for fuels. In the modern sense, therefore, the nonmetallic mineral industries are new and afford new opportunities for engineer and economist alike. A certain amount of caution is indicated, therefore, before attempting to apply ready-made formulas to the problems of these industries. Economics is not an exact science. In the field of production technology where the number of variables is fairly well known, the principles of economics are readily applicable, but as the student proceeds through the province of marketing into the unexplored regions of psychology and sociology he must distinguish carefully between scientific reasoning and purely metaphysical speculation, even when the latter masquerades as economics. The present paper attempts to prove no preconceived theorems and is designed primarily to stimulate careful thinking on sundry neglected phases of these industries. An attempt is made to differentiate the general problems into single aspects which afford promise of being comprehended separately; also, some fundamental statistical data are presented, but merely to indicate a method of scientific approach applicable to more intensive studies. Definition Before discussing the economics of the nonmetallic mineral industries, it is appropriate to consider what we mean when we say "nonmetallic minerals." This term, inasmuch as it is merely a negative description, is somewhat loose and ambiguous and gives rise to questions in regard to minerals that, like chromite or bauxite, are alternatively classed either as nonmetallic or as metallic minerals (or ores). The chrome ore used to make ferrochrome for steel manufacture is undoubtedly metallic in character; similar material destined for use as a refractory in the same

Jan 1, 1934

By Richard E. Chism

SAN DIMAS, in the State of Durango, Mexico, on the frontier of the State of Sinaloa, is the centre of an extensive and rich mining region, which has been exploited for over a hundred years; and the patio process for working silver ores has there attained the highest perfection of which it is capable. Local modifications have been engrafted upon the underlying principles of the process, but, as a whole, the San Dimas practice so fully illustrates its typical capabilities, that I have undertaken to describe its workings in the hope of lightening, to some degree, the labors of my professional brethren who may have occasion to visit Mexico." As is tolerably well known, the patio process, like all other systems of free amalgamation, is not successful with ores containing more than a trace of zinc or lead, the presence of zincblende being especially obnoxious. Iron and copper in small quantities are not particularly disadvantageous. The process succeeds very well with all sulphide ores which do not contain much more than a trace of arsenic and antimony, provided the tailings are concentrated, although, of course, it is best adapted for free milling ores. For suitable silver ores that contain small amounts of free gold the process is still a good one, but where the gold is combined with sulphurets, a considerable and even an excessive loss is inevitable. Hitherto the Mexicans have submitted to this loss, but, since the introduction of American mills, they are gradually abandoning the patio process in favor of the other. The San Dimas ores have a gangue of quartz and feldspar. They are composed principally of silver sulphides, with some chloride and

Jan 1, 1883

By Philip Wilson

Tun mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic limestones of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft. the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances away from the zone of contact metamorphism.

Jan 7, 1916

By J. E. Lawver, J. D. Raulerson, J. P. Bernardi, R. S. Hearon, D. Lynch, G. F. McKereghan

Despite recent economic problems, the future of the Florida phosphate industry appears optimistic. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal, and land reclamation. The geology and mineralogy of future deposits are discussed with reference to specific deposits. Lower ore grades, increasing power costs, and environmental regulations are necessitating development of new concepts of mining and matrix transportation. Because one of the ores to be mined in the future contains appreciable amounts of dolomite, research and development efforts are being concentrated on new techniques in beneficiation. Changes are being made in plant design to meet environmental and regulation standards. However, the expected new technology outlined for the industry depends on the geology and mineralogy of future reserves.

Jan 1, 1985

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By Sidney H. Loram

As the work carried on by this Company, of which the writer has been in charge for the past two years, is somewhat unique, the following account of it may be of interest, and, on that account, is offered to the Institute without any attempt to claim this practice as the best. Mines. The mines supplying ore to the Company arc situated in three groups: the Guanaco field,.about 80 miles N.E. of the port of Taltal (lat. 25" S., long. 70" 30' W. of Greenwich); the Sierra Overa, about 63 miles S.W. of Taltal; and Paranao, about 42 miles due N. of Taltal (12 miles N. of the small town of Paposo, once famous for its copper-output). Guanaco. This field lies in the center of an absolutely waterless mountainous desert, where not a sign of vegetation can be found for miles. The dryness is such that ivory and horn crack and open, while raw-hide must be used in place of leather, which -would become worthless in a very short time. Water is brought about 21 miles by piping from the Cordillera, but only in small quantities, and costs in the Guanaco $7 (= $1.78 gold) per cubic meter. All supplies and food are sent from the port of Taltal, which in turn draws its supplies from the south of Chile, the

Jan 1, 1900

By P. F. Gnirk, J. B. Cheatham

The basic objective of this paper is to present a review of the state of knowledge concerning the fundamental mechanics of rock/bit-tooth interaction under downhole conditions. Of particular concern is the contributing significance of the various variables associated with the generation of rock chips by a single penetrating bit-tooth. The variables to be considered are fluid pressures which simulate borehole conditions, the mechanical properties of the rock, the shape and angle of attack of a bit-tooth, and the rate of load application on a bit-tooth. In addition, consideration is given to multiple bit-tooth penetration insofar as the effects of distance from and geometrical shape of adjacent penetration craters are concerned. Both experimental results and idealized theoretical models for single bit-tooth penetration are presented. Finally, the applicability of plasticity theory to drilling phenomena at depth, results of recent drag-bit studies, and several general theories of roller-bit drilling are briefly discussed. FUNDAMENTALS OF ROCK/BIT-TOOTH INTERACTION Drilling efficiency at depth in terms of penetration rate depends largely upon three essentially interdependent factors: 1) the bit, insofar as the mechanical motion, shape, and configuration of the bit-teeth are concerned; 2) the rock, as regards its mechanical behavior, or response to the penetrating action of the bit-teeth, when subjected to a state of stress induced by mud column, interstitial pore, and overburden pressure (and at great depths to high temperature) ; and

Jan 1, 1967

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is - and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result : Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobusea grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton.

Jan 1, 1935

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,' Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer's suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By R. D. Leitch, W. P. Yant, R. R. Sayers

In 1924, the United States Public Health Service was requested to undertake a special study of stream pollution. The Public Health Service asked the United States Bureau of Mines to take up the study because the training and experience of the personnel of the former was considered not to be as well suited to this type of investigation as that of the Bureau of Mines. Under H. Foster Bain, then Director of the Bureau, field investigations were begun in the spring of 1925. Along with mine-drainage wastes, the problem of gas-house and coke-oven waste was investigated in the laboratory and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau Experiment Stations, on a trip to Germany in 1924. He saw a practical application of the process, but obtained no information as to definite chemical or mechanical processes. Because of the then pending American patent applications by the German firm, we made no attempt to develop our findings further. Shortly afterward, a similar method of treatment was developed in the United States,' and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage. Scope of Work There was such a diversity of opinion at the time this work was begun, on the whole subject and apparently so little accurately known, that it was decided to undertake a basic study from which first, certain definite information might be evident, and second, what might be considered

Jan 1, 1931

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By C. H. Herty

The elimination of metalloids in the open-hearth process depends on oxidation of the metal by diffusion of FeO from the slag (or absorption of FeO by the metal), with subsequent reaction between dissolved iron oxide and the metalloids carbon, manganese, phosphoms, and silicon. During an investigation on deoxidation with silicon, data on rate of oxidation of the metal were obtained, and these combined with certain other information, are presented here in an attempt to show the fundamental principles governing the diffusion of FeO from slag to metal. Inasmuch as the aim of the investigation was not a study of diffusion, certain data are lacking and it has been necessary to make assumptions on metal viscosity and effect of temperature on diffusion. These factors are known to exert a considerable effect on diffusional processes. Overoxidation, or supersaturation of the metal with iron oxide, is not taken up in this paper. Overoxidation has little effect on diffusion except under a few special conditions, and the discussion has therefore been limited to diffusional processes. Though the results given in this paper should be regarded as preliminary, certain of the conclusions drawn are definitely applicable to any steelmaking process. Previous Study of Absorption An extensive study of absorption has been made by the Department of Chemical Engineering, Massachusetts Institute of Technology. The results are of such direct interest in the problem of slag-metal reactions that it is feIt worth while to summarize them here. The following quotations are from Lewis and hitmman.1 The reader need simply substitute "slag and metal" for "gas and liquid," with proper modifications to take into account the variations in physical properties of

Jan 1, 1929

By Marvin L. Kay

In the spring of 1950, just two years after the inauguration of the domestic uranium program by the U. S. Atomic Energy Commission, the company entered the uranium mining and milling business through a newly formed subsidiary, Climax Uranium Co. This was the first venture into a new field of mining for Climax, which became the first old-time mining company, other than the vanadium producers, to become active in the embryo uranium industry. Twenty-five years earlier, Arthur Bunker, president of Climax Molybdenum, organized and operated the U. S. Vanadium Co. at Rifle, Colo. With this background, he viewed the budding industry of the Colorado Plateau with much interest. Upon its formation, the new subsidiary entered into a con- tract with the U. S. Government and the potential uranium-vanadium properties of Minerals Engineering Co. were assigned to Climax Uranium Co. Funds for the construction of a processing plant and working capital were advanced by Climax Molybdenum Co. The old sugar mill building of the Holly Sugar Co. in Grand Junction was leased to house the extractive plant. Construction of facilities, which were based upon a new process developed for the treatment of both uranium and vanadium ores, was completed and the mill was placed in operation early in 1951. Subsequent to that time several alterations were made and the capacity of the plant increased. In terms of recoveries, the plant has proved to be one of the most efficient on the Colorado Plateau

Aug 1, 1955

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By Samuel Shallcross

THE principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the line-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania.

Jan 1, 1936

By Molly Gleiser

The standard free energies of formation of some gaseous metal oxides together with those of their condensed oxides have been plotted against temperature. The heats of formation of the gaseozcs oxides are tabulated. An explanation is given of the use of the data to predict the importance of the gaseous metal oxides at high tenzperatures. RECENT mass spectrometric work1 has resulted in the detection of several hitherto unknown gaseous oxides and the measurement of their free energies of formation. Of especial interest is the fact that several of the refractories in common use either as crucibles or furnace tubes, and metals used in Knudsen cells and in furnace windings, have been found to have one or more stable gaseous oxides. In view of the present emphasis on high-temperature techniques, the development of vacuum metallurgy.z heating by electron bombardment and plasma jets, and the resultant shift to ever higher temperatures, it is no longer possible to plan experiments without taking into consideration the significance of the presence of these gases in the system, the reactions they undergo. and their contribution to the vapor pressure. A good example of what went wrong in earlier work, when the existence of these gaseous molecules was not yet known, is presented by the work of Hoch, Nakata, and Johnston. Hoch and coworkers attempted to measure the vapor pressure of solid ZrO2 by letting the vapor in equilibrium with zir-conia effuse from a tantalum Knudsen cell. The free energies of formation of solid zirconia and tantala are such that a short calculation showed that the reaction

Jan 1, 1962