Search Documents

By H. W. Knott, M. H. Mueller, P. A. Beck, W. P. Chernock

PREFERRED orientation studies by Harris of rolled uranium rods indicated that hot rolling to a small reduction of area caused the (010) planes to become strongly oriented and the (110) planes weakly oriented perpendicular to the rolling direc- tion. The relative intensities of these two fiber texture components were reversed upon rolling to higher reductions of area. Cold rolling caused the (010) planes to become strongly aligned and the (130) planes weakly aligned perpendicularly to the rolling direction. The present investigation was undertaken to explore in more detail the effect on the rolling texture of variables, such as the penultimate condition, the final rolling temperature and reduction of area. In addition, the recrystallization texture of rolled uranium rods was also investigated.

Jan 1, 1959

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

Sifto Salt Div. of Domtar Chemicals Ltd. has developed a new method for installing roof bolts in the high backs of its 1-million-tpy rock-salt mine at Goderich, Ontario, on the east shore of Lake Huron. The method teams a telescoping- boom hydraulic crane with a specially developed combination auger-drill and bolt-tightening ma- chine. One man, controlling all operations from a basket supported at the end of the crane's telescoping boom, installs an average of 100 5-ft roof bolts per shift, at heights to 45 ft. The mine has very long backs that are not as stable as might be expected. The result has been that roof scaling has occupied an unusually high percentage of the underground work force. About six years ago, company officials decided to go to 100% roof bolting of all backs as a safety measure. The present roof-bolting equipment is the result of a development program instituted at that time to find a faster and more economical method for doing the job.

Jan 9, 1967

THE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently attempted to make a much too simple correlation between mineral discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail

Jan 1, 1941

By William L. Saunders

Many members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-coxpressors and machinery driven by compressed air, has no desire to injure its own business by claiming for this new machine that it should immediately supersede all existing applications of pneumatic transmission of power for drilling. On the

Jan 1, 1908

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts'-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presenta- tion of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about 1/4 in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 1, 1959

By William L. Fink, H. R. Freche

This is the thirteenth paper of a series from the laboratories of the Aluminurrl Company of America presenting the results of investigations of equilibrium relations in aluminum-base alloys prepared from electro-lytically refined aluminum. The ninth paper, on The Constitution of High-purity Aluminum-titanium Alloys,' presented a type of system that had not previously been encountered in aluminum alloys. Subsequent work has shown that there are several similar binary aluminum diagrams including that of aluminum and chromium. The present investigation was limited to the cxtreme alnminum end of the aluminum-chromium system. The first systematic investigation of the aluminum-chromium equilibrium diagram was carried out by Hindrichs.? The resulting equilibrium diagram with some imaginary additions suggested by Guillet3 is shown in Fig. 1. Recently Goto and D6gane4 investigated the constitution of aluminum alloys containing up to 32 per cent chromium, and presented the diagram that is reproduced in Fig. 2. Wide discrepancies in the two diagrams are evident. The following intermetallic compounds have been reported in the literature: A1Crl5,6 AlloCrlzSi,5 AlCr4,6 AlCr3,7 AlaCr.8 Preparation of Alloys and Chemical Analyses With the exception of sample Y4206, which will be described under Determination of Hyperperitectic Liquidus, the alloys were prepared from electrolytically refined alurninum% Of which the analysis is given in

Jan 1, 1933

By T. Egleston

The treatment of the residues from the manufacture of sulphuric acid which contain small amounts of copper, silver and gold, has attracted considerable attention in Europe. They are successfully treated in several works on the continent, and in as many as twenty establishments in different parts of England. As the process must sooner or later attract attention in this country, I have put together my notes made in three of the most important establishments in Europe. These are the works at Hemixem near Antwerp, of Duisbourg in Westphalia, and of Oker in the Hartz. In the last works only, the ores are produced in the vicinity of the place where they are treated. The works at Duisbourg treat ores which come from the Rio Tinto mines in Spain, which often contain considerable quantities of arsenic. They are roasted in a number of different works along the Rhine for the manufacture of sulphuric acid. They are brought by boat and are landed at the works by steam-cranes. They are carried at once by a double-inclined plane worked by steam to the storagehouses to be kept, until treated. The wagons, after being weighed, are dumped. The ore is assayed at once, the assay-sample being taken from the boat while the ores are being discharged. They are all fine, and contain two to eight per cent. of copper and about sixty per cent. of iron, and a small amount of silver and gold. Their average composition is given below:

Jan 1, 1886

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887'0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937'0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By John V. Beall

Given: One large, but dated open-pit copper mine and processing plants, down about one third in production capacity in decade because of declining ore grade. Solve for: Restoration of former peak capacity without further losses during period of reconstruction. That is the problem that Kennecott's Utah Cop- per Division began solving in 1963. Most of the work went to a task force of engineers, several of whom were plucked out of line jobs and assigned to the so-called "Expansion Project" for the duration. There was no doubt from the beginning that effective cooperation between Expansion Project engineers and operators was critical to success, and personnel was chosen accordingly. This foresight paid off. The Expansion Project is all but complete, and the Utah Copper Division is returning to its rated capacity of 300,000 tons per year of copper metal.

Jan 6, 1967

By Howard Willey

MINING operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of San Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This -paper describes the so-called "filled top slice" stoping method finally adopted as the standard system.

Jan 1, 1930

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By W. F. Carew, H. D. Kessler, F. A. Crossley

AS part of a program on phase relationships and transformation processes of titanium alloy systems, the titanium-rich corner of the Ti-Mo-V system has been investigated. This region was surveyed primarily to supply information toward the development of a creep resistant, weldable alloy, with a minimum alloy content, for use in the 425° to 550 °C range. Specifically, the investigation was directed toward the development of a stable ß alloy with less total alloying additions than is found in the Ti-30 pet Mo alloy. A secondary objective was the development of a creep resistant, weldable a-ß alloy for application around 300°C. Molybdenum was selected as primary additive to titanium on the basis of an investigation1 which showed that the Ti-30 pet Mo alloy had promising elevated temperature tensile properties. Furthermore, aging studies1 showed no tendency for this

Jan 1, 1957

By E. S. Hutchinson

The subject of the influence of coal-dust in mine-explosions has received considerable attention both in England and on the continent of Europe, but until the recent disaster at Pocahontas, Va., it seems not to have been of special interest to engineers in this country. The reason, perhaps, is that most of our bituminous mines are worked by short shafts, slopes and drifts; few have been specially dry; and the explosions that have occurred could readily be traced to fire-damp with 110 complicated circumstances. The object of the present paper is to bring together, for the convenience of members of the Institute, the principal English opinions upon this important subject. Messrs. Lyell and Faraday, in their report to the Home Secretary," in England, on the Haswell Colliery explosion in 1844, seem to have been the first to point out that dust fed the flame originating in a

Jan 1, 1885

By Thomas Fraser

There are large coal reserves in Argentina, Brazil, Chile, Colombia, Peru and Venezuela, and growing productive industries in Brazil, Chile, Peru and Colombia. The paper describes current activities in these coal fields, and improvement programs that are in progress, or are planned. Special emphasis is placed on improvements in mining and preparation practice, and expansion of production that have been accomplished by American equipment and technical assistance.

Jan 4, 1951

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

By D. L. Wood

This investigation was concerned with the aluminum-oxide particle dispersions, the mechanical properties, and the re-c,uystallization characteristics of some internally oxidized copper-aluminum alloys. Obserued hardness vaviations are in agreement with variations in oxide particle size revealed by electron metallographic studies. The increase in yield strength caused by internal oxidation is quite sensitive to matrix grain size and is accompanied by a loss of ductility, particularly at higher temperatures. Elevated temperature ductility is con-side,vably improved if major grain reorientation is accomplished by ve recrystallization prior to testing. The oxide particles offer a considerable restraint to softening during annealing after cold deformation. THE diffusion of oxygen under appropriate conditions into a suitable alloy causes solute oxide particles to be precipitated at an inward moving interface.1,2 Previous work has shown that the hardness

Jan 1, 1960

By Fred J. Hurst

In 1934, Irvin Lavine (A), University of North Dakota, stated that the low-rank coals (lignite and subbituminous) of this country represent a vast tonnage of fuel of commercial value and predicted that some day they will play an important role in our economic welfare. Lavine also pointed out that one of the major problems with efficient utilization of the low-rank coals is their high moisture content. Following the discovery of uranium-bearing lignite in the Williston basin of North and South Dakota in 1948 by D. G. Wyant and E. P. Beroni, detailed investigations were conducted (primarily during 1950 to 1954) by members of the U. S. Geological Survey to evaluate the geologic factors and economic possibilities of the radioactive lignites as a source of uranium. The information gained in these studies and summarized in several papers indicated that a large potential reserve of uranium is contained in the subbituminous coal and lignite deposits of the Dakotas and Wyoming (2,3,4). Most investigators concluded that an epigenetic emplacement of uranium in the coal by means of circulating groundwater and the more extensive concentrations of uranium in coal are apparently related to the permeability of the rocks enclosing the coal beds. Breger (5) and others have shown that uranium is readily adsorbed by coal and is held irreversibly as a disseminated adsorbed constituent. Briefly, lignite beds containing 0.1 to 10% uranium have been discovered in the Dakotas and Wyoming. The distribution of uranium was found to be erratic and was usually concentrated in thin layers, which were characteristically 10 to 14 in. thick and occasionally 30 to 36 in. thick. Lignite beds more than 3 ft. thick generally contain more uranium at the top of the bed than at the bottom. Special strip mining techniques are required to mine these thin

Jan 1, 1983