Search Documents

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By W. C. Elmore

THE magnetic powder method, long used. for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickels single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By David H. Davis, John Griffen

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944

By H. S. George

On one occasion when it seemed desirable to reveal under the microscope not only the metallic structure of an alloy, but certain small non-metallic inclusions that are ordinarily obliterated by etching, it was discovered that, by partly eclipsing the illuminating pencil of light rays, the residual light was thrown on the object from one side and the structure was brought out in relief. At the same time, the non-metallic inclusions were retained in clear view. In this first demonstration of lighting obliquely through the objective a card was thrust part way into the light beam between the arc iris and the light filter; the shadow of the card on the filter served to locate its position. Next several stiff-paper disks of various diameters were mounted on flexible wires; some plasticine on the other end of the wires made it easy to adjust and maintain a disk at any desired position in the light beam. To facilitate manipulation, an assortment of disks was mounted on a wheel, as shown in Fig. 1. The purpose of partly eclipsing the light beam was discussed in an earlier paper.' There it was pointed out that the usual methods of illuminating opaque objects for microscopic examination lend an unnatural appearance to the view, while the new method, which has been termed conical illumination, revels the true relationship of constituents by simulating natural lighting. In nature, all objects are lighted diffusely, or by light predominating from one direction, or by a combination of diffuse and directed light. Under these conditions, objects appear to have three dimensions—they possess relief. The kind of illumination known to metallographists as vertical or axial results in an unnatural appearance, as a large proportion of the illuminating rays are parallel to the line connecting the eye with the object, a condition almost never met in nature. Microconstituents

Jan 1, 1924

By Robert E. Green

Experiments were performed in order to investigate the influence of magnitude of driving force, recouery, and previous heat treatment on grain boundary migration in deformed aluminum crystals. The frequency of occurrence of strain-free grains possessing Preferred crystallographic orientations was studied both as a function of heat treatment and as a function of amount of deformation of the matrix crystal. Aluminum of such composition as to exhibit precipitation-hardening behavior was used. CONSIDERABLE work has been devoted to the factors influencing grain boundary migration in metals.1'52 Aust and Rutterl-9 have studied grain boundary migration into matrix crystals containing a striation substructure, which provided a thermally stable driving force during the course of the migration experiments. These authors state that, while variations in the striation pattern were sometimes observed, it was possible to obtain reasonably uniform and reproducible striation structure by careful control of the solidification conditions. Admittedly, this source of driving force is a unique one and has served well in numerous experiments. However, although the striation substructure provides a thermally stable driving force, the subject of its reproducibility from crystal to crystal is questionable. In fact, Aust and Rutter3 attribute the scatter shown in some of their experimental points and several anomalies in boundary migration rates to variations in the substructure driving force along a single specimen. A further limitation on striation-induced driving force is that the driving force cannot be varied over wide ranges in a controlled manner. More often used as a source of driving force is the strain energy stored in a crystal during plastic deformation. This type of driving force has the disadvantage that it is not thermally stable due to recovery taking place simultaneously with the grain boundary mobility measurements. On the other hand, this strain-induced driving force is very reproducible from crystal to crystal since it is very easy to grow single crystals possessing the same purity and crystallographic orientation and then to strain them identically. In order to measure grain boundary migration rates two different methods are primarily used. Most often the technique employed is the heat-cool-etch method1' which involves thermal cycling, while the other technique, developed by Graham and Cahn11 using an X-ray diffractometer and goniometer furnace, involves continuous heating only. Thus the influence of thermal cycling vs continuous heating is a factor to be considered in grain boundary migration rate measurements, particularly in cases where the source of driving force is the strain energy stored in the deformed matrix, and recovery is likely to occur. Numerous recent investigations have shown that extremely small impurity additions to zone-refined metals exert a marked effect on grain boundary migration rates1-5, 9, 12-27 and a few have considered the effect of the distribution of impurities.28-35 The concentration of impurities and their distribution as influenced by heat treatment must also be taken into account in migration-rate studies. In the present article consideration is given to the influence of the magnitude of driving force, recovery, and previous heat treatment on grain boundary migration rates. In order to vary the driving force over a large range it was necessary to use as a source of driving force the energy stored in the matrix crystal during plastic deformation. A majority of the investigations were performed on aluminum specimens which were of such compositions as to exhibit precipitation-hardening behavior.

Jan 1, 1965

J. R. Lane (Metals Research Laboratory, Washington)—A new type of deformation called "kinking" has recently been described. Is there any relation between the "rumpling" described in this paper and "kinking?" D. C. Jillson (author's reply)—Both are manifestations of bending about [210] axis. The difference is one of degree. W. C. Ellis (Bell Telephone Laboratories, New York) —Some observations of deformation in zinc recorded in this paper may be applicable generally to flow in metals. One of these, deformation in torsion without evidence of slip or twinning in the early stages and with startling ease, when the twist is about the hexagonal axis, adds another method of flow to the presently increasing list of mechanisms. This illustrates again that a crystal will utilize any realizable process to flow and relieve stress. The process is not necessarily classical directional slip—& this case, it is rotational slip. The question naturally occurs: Will face-centered cubic metas stressed by twisting about an octahedral axis flow in a similar manner by rotation on an octahedral plane? I would like to ask Dr. Jillson if he has made any experiments or knows of any experiments of this type on face-centered cubic metals? Face-centered cubic metals possibly would behave differently from zinc, since, for one thing, the stacking sequence is different for the two structures. The results of such experiments, however, would be instructive in providing more information about deformation processes. D. C. Jillson—Dr. Roy E. Swift, working in the Hammond Laboratory at Yale, performed a twist test on a single crystal of brass. The work has not been published, and I do not know the crystallographic direction of the axis of the specimen used. Lo-ching Chang (Columbia University, New York)— Observations similar to Figs. 1 and 2 of the paper were obtained by us during the bending and unbending of an orthorhombic Au-Cd alloy.'l This orthorhombic alloy is the product of diffusionless transformation from a single crystal of p Au-Cd alloy (CsC1 structure) containing 47.5 atomic pct Cd on cooling to about 60 "C.62 Referring to the effects of annealing, has the author tried any loilg time high temperature anneal, such as 150 to 200 hr at 40O°C? D. C. Jillson—No. C. Crussard (Ecole des Mines, Paris: France)—I

Jan 1, 1952

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

By W. D. Robertson, E. G. Grenier, V. F. Nole

The electrical, mechanical, and corrosion cracking properties of an age-hardenable Cu-Ni-Si alloy have been studied over a range of time, temperature, and deformation states for the purpose of determining the relationship between the properties and the structural state. The precifitate has been identi3ed as and the sites of preferred precipitation have been located by electron microscope studies of the structures developed by various combinations of heat treatment and plastic deformation. An extreme form of deformation banding has been observed in the aged alloy that results in high strain concentration in bands lying parallel to {111} planes. These bands are the structural paths along which transcrys-talline cracks propagate in the deformed alloy. The observations provide a basis for a general mechanism of transgranu-lar corrosion cracking of face-centered cubic alloys in terms of stacking fault probability. AMONG the age-hardening copper alloys the copper-nickel-silicon (Silnic Bronze) type is outstanding in exhibiting a high strength combined with a considerable capacity for cold working, a relatively high conductivity, and a low to negligible susceptibility to stress corrosion cracking. It is not a new alloy and it has been the subject of a number of investigations,1-5 which were made primarily to establish practical composition and heat treatment limits. The structural characteristics of the aging processes in this alloy have not previously been studied in detail. This particular investigation was undertaken to explore, in detail, and over a wide range of conditions, the properties obtainable by various combinations of working and heat treatment and to correlate structural changes with the observed mechanical, electrical and corrosion properties. MATERIAL AND PROCESSING Eight different commercial heats of the alloy were made and used in the investigation. The range of composition among the eight heats is shown in Table I. Billets, 8 by 24 in., were cast into water-cooled molds, extruded to 1.687-in. rod, and quenched in water after extrusion. Extruded material was rod rolled to 0.750 in., annealed at 1450° F for 2.5 hr, and quenched in water. Subsequent working operations were performed by tandem rolling to various sizes depending on the degree of reduction required. Final cold-working operations were performed by drawing to a uniform size of 0.187 in. diam and straightening by a roller straightening machine (Lewis). The combinations of heat treatment, working and aging that were investigated are summarized in Table 11; the various treatments were performed in the order given in each row of the table, and they will be subsequently identified by the symbols shown in the first column. SOLUTION TREATMENT All material investigated in the cold-worked condition, or cold worked prior to aging, was solution

Jan 1, 1962

By Stuart Croasdale

Not long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale. Temperature, Degrees F. High Low Average June...................... 112 62 84.0 ' July...................... 115 71 87.8 Evaporation June July Concrete tank, inches............ 11.7 10.72 Iron tank, inches.............. 14.8 13.07 Rainfall, inches................ None 0.77 Cloudy days................... None 10.00 Aside from several springs about 10 miles from the property, the nearest known water in quantity at the time these experiments were made was the Gila river at Gila Bend, 45 miles distant. Part of the developinent of the property of course included drilling for water in the valley, which was in progress at the conclusion of my experiments. The ore deposit itself is unusual. It consists of of intrusive plug of monzonite or granite porphyry. Chalcopyrite, bornite, and magnetite are finely disseminated throughout the magma in sufficient quantities to make the greater part of the mass commercial ore to a certain depth.

Jan 1, 1915

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

By Albert Sauveur

IT WAS in June, 1889, that I was first admitted to the society of educated men. The admission ticket had been signed, on the recommendation of my old and beloved teacher, Bobby Richards, by General Francis A. Walker at the time President of the Massachusetts Institute of Technology, an institution familiarly known as M. I. T. I immediately proceeded to take advantage of that privilege by departing for Steelton, Pennsylvania, where I understood I was eagerly awaited by the educated officials of the Pennsylvania Steel Company. I was some. what disappointed at the casualness of my reception and at being tucked away in that preserve closet of steel works known as the chemical laboratory. At Steelton I met Major Bent who was president of the company. When I say "met," that is a figure of speech as my acquaintance with him was confined to my being shown

Jan 1, 1937

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By J. O. Betterton, D. S. Easton

A detailed investigation was made of the phase diagram of silver-zirconium, particularly in the region 0 to 36 at. pct Ag. The system was found to be characterized by two intermediate phases Zr2Ag and ZrAg and a eutectoid reaction in which the -zirconium solid solution decomposes into a-zirconium and Zr2Ag. It was found that impurities in the range 0.05 pct from the iodide-type zirconium were sufficient to introduce deviations from binary behavior, and that with partial removal of these impurities an increase in the a-phase solid solubility limit from 0.1 to 1.1 at. pct Ag was observed. The phase diagram of the silver-zirconium system is of interest as an example of alloying a transition metal from the left side of the Periodic Table with a Group IB element. Silver would normally act as a univalent metal, its filled 4d-shell remaining undisturbed during the alloying. However, there is a possibility that some of the 4d electrons might transfer to the zirconium. An insight into such a question can occasionally be obtained by comparison of phase diagrams. The silver-zirconium system forms part of a more complete review of various solutes in zirconium in which these valency effects were studied.' Earlier work on the silver-zirconium system was done by Raub and Enge1,2 who investigated the silver-rich alloys. After the start of the present experhents, work on this system was reported by Kemper3 and by Karlsson4 which for the most part agrees with the phase diagram presented here. EXPERIMENTAL PROCEDURE The alloys were prepared by arc casting on a water-cooled, copper hearth with a tungsten electrode and in a pure argon atmosphere. Uniform solute composition was attained by multiple melting on alternate sides of the same ingot. Progressive improvements in the vacuum conditions inside the apparatus during the course of the experiments reduced the Vickers hardness increase of the pure zirconium control ingot from 10 to 20 points, observed initially, to negligible amounts at the end of the experiments. Such hardness changes in zirconium are a well known indication of purity. For example, -01 wt pct additions of oxygen, nitrogen, and carbon increase hardness by 6, 10, and 3 VPN respectively. '9' Further verification that the final casting technique did not add a significant quantity of impurities was obtained when pure zirconium was arc cast and then isothermally annealed in the vicinity of the allotropic transition. The transition was always observed to take place over the same temperature range as in the original crystal bar. The alloy ingots were annealed in sealed silica capsules for times and temperatures which varied between 1 day at 1300°C and 60 days at 700°C. The best method found to prevent the reaction of the zirconium with the silica was foil wrapping of molybdenum or tantalum. With this method, samples of pure zirconium were found to be unchanged in hardness after annealing for 3 days at 1200°C. In most of the experiments the protection of these foils was supplemented by an additional layer of zirconium foil inside the molybdenum or tantalum foil. The alloys, foil, and the capsule were outgassed at pressures in the range 10 to l0-7mm Hg in the temperature range 800" to 1100°C before each anneal in order to remove hydrogen and other impurities, and to provide a suitable container for the high purity, inert atmosphere, which is essential in the annealing of zirconium. The temperature measurements were made with Pt/Pt + 10 pct Rh thermocouples calibrated frequently during the experiments against the melting points of zinc, aluminum, silver, gold, and palladium. For the longer anneals the sum of various temperature errors was generally well within ± 2°C. For short-time anneals and during thermal analysis the overall temperature error is considered to be within ± 0.5°C. The compositions of the alloys from the quenching experiments were determined by chemical analysis at Johnson Matthey and Company, Ltd., under the direction of Mr. F. M. Lever. The actual metallo-graphic samples were individually analyzed in every case, and prior to the analyses two or more sides of each specimen were examined to insure that the specimen was not segregated. The sum of the solute and solvent analyses was in each case within the range 99.9 to 100.1 pct. In the course of the experiments, minor impurities in the range 0 to 500 ppm were found to have significant effects on the zirconium-rich portion of the phase diagram. Similar effects had been encountered previously in other zirconium phase-

Jan 1, 1959

By R. S. Dean. J. R. Long T. R. Graham, Roberson A. H., Armantrout C. E.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig' ') has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947