Search Documents

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By M. C. Miller, M. R. Tek, D. L. Katz

Previous studies have shown the influence of geometric variations on the drawdown and buildup behavior of a well completed in a homogeneous, porous medium containing a single-phase fluid. Other papers have shown the influence of leakage across caprocks on drawdown tests on water wells and aquifers. This paper presents two additional cases: the influence of an adjacent, expansible source of fluid, and the effect of caprock leakage on the measured in situ permeability and compressibility. Methods are developed for evaluating the influence of these two deviations from a uniform aquifer upon the in situ permeability and compre.ssibility indicated by pump tests. INTRODUCTION In relatively uniform porous media, saturated with a single-phase fluid, the effective reservoir permeability and compressibility of the water porous bed system may be obtained from drawdown and build-up data on wells, such as the initial wells drilled in aquifer storage reservoirs (Homers and Katz et al.7). In considering the drawdown and build-up behavior of wells adjacent to storage reservoirs, or of wells in an aquifer adjacent to an unknown gas field, questions arise as to the quantitative effect of the presence of compressible fluid on the measured permeability and compressibility of the formation. The solution to this problem is presented, using a constant pressure line source at some distance from two wells, one of which is pumped and the other used as the pressure observation well. The solution is presented in terms of the geometry of the wells and their relationship to the constant pressure line. It is known that caprock leakage can interfere with the determination of an aquifer in situ permeability and compressibility (Mantush4, Hantush and Jacob3 and Witherspoon and Muellerll). This paper presents an added case of the effect of leakage through a caprock of known thickness and permeability on well tests starting with a reservoir of constant pressure above the caprock and contributing to the aquifer as a result of the pump test. Again, both a pumping well and an observation well are postulated. These two cases are presented together since both a compressible fluid nearby and. caprock leakage show similar deviations from expected in situ permeability and compressibility results, and the solutions are similar in form. EFFECT OF A NEIGHBORING CONSTANT PRESSURE SOURCE ON IN SITU MEASUREMENTS Bixel, Larkin and van Poollenl presented a paper showing the influence of a discontinuity of the properties of a fluid formation system on drawdown and build-up performance. Their case is related to the present study but may be distinguished from it in that their numerical work and resulting graphs relate only to the performance of the pumping well itself. Incorrect values for in situ reservoir properties may be obtained from pump test data if the skin effect of the well and after-flow are not considered. Analysis of this problem by the authors indicated that the more reliable method of evaluating the influence of an adjacent gas field or expansible source was to use one well for pumping and another well at some distance from it for observing the aquifer pressure performance. An expansible source of hydrocarbon near a pumping well may be approximated by a line of constant pressure for a pump test. Fig. 1 illustrates a pumping well and an observation well near a line of constant pressure. Pressure behavior of an observation well during a drawdown pump test near a line of constant pressure is given by the diffusivity equation:

Jan 1, 1967

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

CHARLES CATLETT, Staunton, Va.-A great many important things have been said in an interesting way but the most startling, to me, is that for 25 years, the price has been in the neighborhood of $1.00, with a minimum of 86 cents and a maximum of about $1.25. It is evident that during all that time the price was inadequate. The amount paid to be divided between the land owner, the capitalist, and the laborer was too limited or too irregular to permit of a healthy condition; yet it is evident that the enormous industrial development of this country was fostered by this very cheap coal, probably the cheapest that has been provided in quantity in any country. I entered the coal business when the price was lowest and my interest and sympathy went out to the man who spent his days in the dirt and foul air of a mine and I was filled with schemes for helping. But at the end of the year, after exercising every economy and in blissful ignorance of proper depreciation and obsolescence, there was still only a profit of 1 cent per long ton for what I think is one of the best coals in the world, the best grade of New River coal. We are now paying a great deal more than we did a few years ago and probably will continue to pay more for some time; but any one who thinks we will not have low prices again is very young or very forgetful. Yet we must have larger profits if the industry is to be healthy, if the three parties to the production are to get adequate returns and be in shape to provide the improvements which will be needed to take the place of and supplement the man-power. This will come when the men are making so much money that the operator wants to replace the man by a machine, and when the operator is making so much money as to be in a shape to make the improvements. He will not put in machinery unless the machinery will save money. We have got to pay a higher prime cost for coal, but engineering skill will teach us how to handle it better and use it more economically, and the ultimate result ought to be of advantage to the public.

Jan 3, 1920

By Maurice Ewing, J. A. Peoples, J. W. Peoples, A. P. Craby

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By A. M. Gaudin, A. F. Taggart

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By C. A. Stout, S. W. Nicksic

The materials that stubilize emulsions of some Southern California crude oils were isolated from the produced crude. These substances were separated into acidic and nonionic fractions by ion exchange chromatography. Each fraction was further broken into groups of homogeneous molecular weight composition by gel permeation chromatography. Both ionic character and molecular weight of the individual fractions are reflected in the properties of the original crude oil emulsion. Specifically, the more acidic and the higher molecular weight fractions appear to be the most effective stabilizers. INTRODUCTION The treatment of oilfield emulsions is a continuing problem for the oil industry. In almost all cases, these are water-in-oil emulsions. Much more is known about the formation and stabilization of oil-in-water (O/W) emulsions than of the water-in-oil (W/O) type. To understand W/O emulsions, more information is needed on the materials responsible for their formation and stabilization. This is especially true in the case of oilfield emulsions where the stabilizing materials are complex mixtures of large asphaltene-like molecules. To study the chemical and physical properties of these emulsion stabilizers, it is necessary first to separate them from crude oil. This separation was achieved in the case of two Southern California crude oils. The materials that were isolated appear at first to be little different from an asphaltene mixture. However, if a mixture of distilled water and mineral oil containing about 1 percent of the natural emulsion stabilizers is passed through a colloid mill, the W/O emulsion formed may be stored in the laboratory for many months without any sign of breaking. This could not be done using undifferentiated asphaltenes from the same wells, indicating that there is a real difference between these materials and ordinary asphaltenes. The colloid mill used to generate the emulsion was required because tile natural emulsion stabilizers had very little effect on oil-water interfacial tension. The one characteristic — complexity of composition — that emulsion stabilizers share with asphaltenes makes virtually impossible the exact structure determination of the components of the mixture. For this reason, it was decided to investigate first the influence of molecular weight on the ability of these materials to stabilize emulsions. The emulsion stabilizers were first separated into acidic and neutral fractions according to whether or not the material was retained on a weakly basic ion exchange column. The extraction procedure was not designed to remove basic components from tile oils, and no attempt to isolate such a fraction was made. Following this separation, selected fractions were analyzed by gel permeation chromatography. Gel permeation separates according to molecular size, largely independently of chemical or polar characteristics. A heterogeneous mixture is separated into a number of fractions having much more homogeneous molecular weight distribution. A number average molecular weight of each fraction is therefore close to the true molecular weight of the principal component of that fraction. The fraction weights, expressed as weight percent of the sample, and the number average molecular weight of a representative selection of the fractions, will be referred to in this paper as the molecular weight profile of the original sample. DESCRIPTION OF GEL PERMEATION ANALYSIS The first reported gel permeation analyses were for separating partially hydrolyzed protein molecules in an aqueous system using expanded starch granules. Most of the theoretical work on gel permeation has been done by biochemists.1 This theoretical treatment is still incomplete, but the

Jan 1, 1969

By Joshua I. Tracey, Mackenzie Gordon

THE bauxite deposits in central Arkansas were formed by weather¬ing, in early Eocene time, of fresh or kaolinized nepheline syenite above the water table in a subtropical climate of fairly continuous moisture. Four types are recognized: (1) residual bauxite deposits on kaolinized nepheline syenite, (2) residual deposits on kaolin and bauxite detritus, (3) alluvial deposits of sorted pebbles and pisolites of early Wilcox age, and (4) rubble deposits of later Wilcox age. All were invaded by kaolin and siderite during subsequent burial by Eocene sediments. PART I-FIELD RELATIONS OF THE DEPOSITS The Arkansas bauxite region for years has produced about 95 pct of the domestic supply of bauxite of the United States and it contains today reserves of more than 40 million tons-nine tenths of the known domestic reserves. During World War II, the Arkansas bauxite deposits were explored jointly by the U. S. Geological Survey and the U. S. Bureau of Mines. Some 6000 holes were drilled by rotary rigs under contract to the Federal Govern¬ment, which resulted in the discovery and delimiting of approximately 20 million tons of ore in place. Detailed study of the many sections cored through the bauxite, of data from a much greater number of drill holes made available by all the operating companies, and of the extensive mine faces exposed in the strip pits, has yielded valuable geologic information about the origin of the deposits. It is now possible to piece together a paleotopographic picture of the deposits and the now-buried land surface on which they formed. The bauxite region in the center of Arkansas (Fig 1) contains two producing districts: one in Pulaski County, just south of Little Rock, and the other in Saline County, about 15 miles to the southwest. The deposits in both districts are associated with hills of nepheline syenite, bosses of a large batho¬lith that was intruded into Paleozoic rocks and later buried beneath coastal plain sediments deposited during Cenozoic time. The folded Paleozoic rocks are exposed in the northwest half of the state and are covered in the southeast half by the nearly flat-lying coastal plain sediments. The older rocks were intruded by nepheline syenite, probably in Late Cretaceous time, and sub¬sequently were eroded so as to expose the top of the batholith. In Paleocene time, marine limestone and laminated black silty clay of the Midway group were deposited in an advancing sea, and covered all but the most elevated parts of the batholith. Erosion of the islands of nepheline

Jan 1, 1952

By Scott Howard

MANGANESE being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Ar3 transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the Ar3 transformation occurs at a temperature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3 quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Ar3 point as falling to 0° C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer,2 using alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 percent for the manganese content at which Ar3 is depressed to 0° C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By Charles C. Fatino, Joel S. Hirschhorn

Loose compacts of strained and annealed stainless-steel powders were sintered at various temperatures and times to determine the effect of residual strains on the sintering behavior. The atomized powders were prepared by annealing, ball milling, and rean-nealing. The residual strains and domain size were determined by a Fourier analysis of X-ray diffvaction dala. The specimens were prepared by siwzultaneously sintering cylinders of both strained and unstrained powder. The evaluation of the sintered compacts included density measurements, metallographic examinations, and analyses of X- ray diffraction data. The results of these studies reveal a definite increase in sintered density and sintering rate for the strained powders. THE pressure compacting of metal powders causes deformation of the particles, mechanical interlocking, and increased contact area. After the deformation, severe residual strains remain in these particles. The subsequent contributions of these strains to the sintering process have been considered to be negligible, since the recovery and recrystallization temperatures usually occur prior to the temperature required for the sintering process. Sintering is con-sidered to be the process by which the powders are transformed into solid compacts at temperatures below their melting points. The sintering operation for stainless steel usually takes place in the range of 2050" to 2400°F (0.84 to 0.95 T,, where T, is the absolute melting point or liquidus temperature) while the temperature required for recovery is approximately 1800°F (0.75 T,). However, it has been shown for several metal powders that densification becomes significant in the range of 0.35 to 0.45 T,.' It is the purpose of this study to determine what effect residual strains have upon the sintering behavior of stainless-steel compacts. Loose compacts were selected for study in order to isolate the strain contributions and eliminate the variables inherent in sintering of pressure-formed compacts. Additional variables were minimized by using only one mesh size, one composition, one particle shape, and also by simultaneously sintering both types of powder. Very little work has been carried out previous to the present study to delineate the effect of strains on sintering behavior. Lenel et 01.2 observed that residual stresses in copper compacts caused shrinkage at comparatively low temperatures. Delisle3 loose-sintered ball-milled electrolytic iron and observed that bonding among particles began at a lower temperature as compared to the behavior of annealed powder. Increased densification of ball-milled oxide powders has also been noted.4'5 EXPERIMENTAL PROCEDURES Powder Preparation. The powder used for this study was a commercial-type 316L stainless steel made by the atomization process. A typical chemical analysis is: C- 0.025 pct Mo- 2.2 pct Cr-18.6 pct Ni-12.5 pct Fe—Balance The atomizing process is essentially the rapid freezing of liquid droplets. This nonequilibrium cooling causes coring to occur and two distinct phases are present within the solid particle, the austenitic phase and the ferritic phase. Due to the presence of this ferritic phase, the particles tended to fracture as well as become cold-worked during the subsequent ball-milling operation. (It was also found that this type of cooling produced a broadened and shifted

Jan 1, 1968

By Russell W. Dayton

THE metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory - is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger, (1)‡ in 1909, was the first to apply polarized light to the microscopic study of

Jan 1, 1935

By H. D. Williams, R. A. Scriven

The distribution of elevation angle of finite plane facets distributed symmetrically about a given axis is derived in terms of the angular distribution of lines which these facets produce in a plane section parallel to the axis. It is assumed that the facets are not markedly elongated in preferential directions. The theory is intended for application to the angular distribution in polycrystalline metals of slip planes and of particular grain boundaries on which certain phenomena such as cavitation can occuv. Illustrative examples are given in closed form and simple numerical techniques are de-ueloped for practical application. The results are applied to the distribution of cavitated boundaries in a copper specimen after fatigue at 400°C and it is found that voids form on the boundaries that exper~enced maximum shear stress. When investigating the distribution of elevation angle between a given axis and planes symmetrically distributed about this axis the angular distribution observed in a plane section parallel to the axis is not necessarily the same as the required distribution. Consequently a technique for processing the results obtained by sectioning methods is required. An example where such a technique would find application is in the problem of intercrystalline void formation during uniaxial tensile creep. Two theories have been proposed to explain this cavitation in terms of the normal and the shear components of stress, respectively. Hull and Rimmer (1959) postulate that the growth of intercrystalline voids is controlled by the rate of supply of vacancies from the grain boundary, the local vacancy concentration being proportional to the normal stress on the boundary. Gifkins (1956) considers that slip arising within a grain causes a ledge to be formed at the grain boundary which is subsequently opened up into a cavity by grain boundary sliding. It might be possible to differentiate between these mechanisms by determining the angular distribution of grain boundaries containing cavities since the former theory predicts a predominance of cavitated facets normal to the stress direction whereas the latter should favor an angle of 45 deg to this direction. In a similar manner an indication may be obtained of the type of mechanism responsible for intercrystalline cavitation during high-temperature fatigue. Davies and Wilshire (1962) have analyzed the slip-plane distribution in a nickel specimen but the problem was not treated in any detail nor was any account taken of the finite extent of the planes being sectioned. Hilliard (1962) has given a very general account of how anisotropy in the microstruciure can be related to measurements taken in one or more plane sections by expressing both the measured and the true angular distributions as expansions in spherical harmonics.* The present analysis is con-

Jan 1, 1965

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920

By N. J. Grant, A. W. Mullendore, Y. Ishida

Creep tests were performed at 500°F on polished specimens of A1-3 pct Cu at stresses of 2000, 4000, and 6000 psi. The effects of the size and distnbution of the second phase were studied in connection with the mechanisms of deformation, especially grain boundary sliding. Although the amount of grain boundary sliding varied considerably for the different heat treatments, yestriction of grain boundary sliding is not due primarily to precipitate on the grain boundary. NUMEROUS prior investigations of grain boundary sliding, notably those of McLean, 1 Rachinger, 2 Rhines, Bond, and Kissel, 3 and Brunner and Grant,4 have established the importance of this phenomenon in the deformation of pure aluminum and its solid-solution alloys at elevated temperatures. An extension of this kind of study to the case of a simple two-phase structure is an important step towards understanding the deformation behavior of more complex alloys. A two-phase A1-3 pct Cu alloy was selected for this study. The creep behavior of alloys in this system has been studied by Sully and Hardy,5 by Underwood, Marsh, and Manning,' and by Pelloux, Chaudhuri, and Grant.7 In these studies, the prior heat treatments were such that some precipitation took place during the tests in most cases. Pelloux, Chaudhuri, and Grant7 studied the creep of A1-2 and 3 pct Cu alloys in the overaged condition. Their results indicated that the structure most effective in promoting high-temperature strength consisted of a fine, closely spaced grain precipitate and large, widely spaced particles on the grain boundary. The present work consists of quantitative meas- urements of grain boundary sliding during creep of an A1-3 pct CU alloy with four different precipitate distributions. The aims were to quantitatively define the role of the second phase on grain boundary sliding, and to obtain information regarding the mechanism of grain boundary sliding. MATERIALS AND PROCEDURE A high-purity A1-3 pct Cu alloy, kindly supplied by Alcoa, was used in this investigation. The composition of the alloy in weight percent was as shown in Table I. This composition is such that A12Cu exists as a second phase at temperatures below 850°F. A homogeneous grain size of 0.6 to 0.8 mm was obtained by annealing the machined test bars for 5 min at 1000°F, furnace cooling to 930°F, and homogenizing for 5 hr. Following the recrystalli-zation and homogenizing anneal, four different heat treatments shown in Fig. 1 were utilized. The F7 and F5 treatments utilize a furnace cool to the aging temperature while Q7 and Q5 have a water quench from the homogenization temperature before aging. Figs. 2 to 5, and Table 11, show the size and shape of precipitate dispersions obtained with the above heat treatments. The heat treatments produce variations in the dispersion both in the grains and along the grain boundaries. Precipitate particles along the grain boundaries are rounded and large (about 1.5 p diameter) in the F5 and F7 structures (Figs. 3 and 5). The grain boundary precipitate was somewhat smaller (0.9 p diameter) in the Q7 structure and no grain boundary precipitate was detected in the Q5 structure using light microscopy. The pre-

Jan 1, 1964

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-' have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.' Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967

By Joseph C. McCaskill

The writer assumes that this volume is not intended to serve as a source of statistics on international trade and that the reader is not interested in wading through a lot of statistical tables copied from the various reporting agencies. Generalizations therefore are made whenever possible and not always is the source of the information meticulously cited. The United Nations regularly publishes trade data on mineral commodities. E. J. Gealy, and C. L Kimbell, of the U S Bureau of Mines (USBM), work with these data and estimate that they cover approximately 78% of total mineral commodities traded. In addition the General Agreement on Tariffs and Trade (GATT) publishes analyses of certain trade data The most complete report of production and trade in minerals 1s probably the international volume of the U.S. Bureau of Mines Yearbook The latest available edition is for 1968, and some of the data in this edition cover only as late as 1967. Unless otherwise stated, the source of data used in the chapter is this Yearbook Other staff members of the Bureau were most helpful and cooperative They are not to be held responsible for conclusions or points of view to be found in the chapter. THE NATURE AND SCOPE OF INTERNATIONAL TRADE The two and a half decades since World War II have witnessed an unprecedented growth international commerce The end of the war found the world economy seriously crippled. Many countries had suffered severe war damage; international trade was disrupted and nations had to resort to exchange controls and bilateral trading arrangements. The postwar recovery, however, was remarkably rapid Within two decades, world Income more than doubled, and world trade which was less than $60 billion in 1948 exceeded $200 billion in 1968, 8 and reached $278 billion in 1970.18 The growing world trade contributed to world prosperity which in turn fostered growth of trade. This dramatic growth of international commerce was made possible by the progressive liberalization of trade and capital movements by the major trading nations of the world which began immediately after the War and has not yet completely lost its steam. The modern-day stimulus of the expanded trade movement was the enactment by the Congress of the United States in 1934, of the

Jan 1, 1976