Search Documents

By Clarence G. Merritt

Stainless iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mlysterious electrolytic effects or comparatively minute non metallic inclusions. Many uses for a steel with such excellent physical properties as are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties,1-2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties—hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C;, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion. Monypenny reports that a loss of hardness is

Jan 1, 1932

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920

By Ivan E. Goodner, Charles H. Fulton

THE subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,1 Bolles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the sulphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to date no effort has been made to correlate the data obtained in the latter researches and apply then to the study of the product called " matte," which is made in such large quantities by copper and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections I. A review and discussion of the various binary systems of the metallic, sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical and chemical properties of these sulphides. II. A description of the results obtained from the chemical and metallographic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Nov 1, 1908

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By John T. Eash, Clair Upthegrove

During recent years nickel has had an increasingly important role as an alloying element in the copper-tin bronzes. Nickel additions not only produce better casting alloys but also make alloys whose properties can be varied by precipitation hardening; thus leading to increased commercial application of copper-nickel-tin alloys. Recent investigations have indicated a decrease in the solubility of tin in the alpha phase as the annealing temperature is lowered and as the nickel content is increased within certain limits. A further change caused by the nickel additions is produced in the excess phase of the copper-tin bronzes. The alpha plus delta eutectoid is replaced by a clear precipitated constituent in the alloys containing up to 15 per cent tin and not less than 1 per cent nickel. This paper has a dual purpose. The first is to present a new determination of the alpha-phase boundary in alloys containing from 0 to 20 per cent nickel, together with the liquidus and solidus temperatures above that field. The second purpose is to give the equilibrium conditions existing in alloys exceeding the alpha phase containing up to 31 per cent tin and 5 per cent nickel, so that the disappearance of the alpha plus delta eutectoid constituent may be explained. After considering the earlier investigations of the related alloy systems and the experimental procedure used in this investigation, the alloys will be discussed in groups as separate quasibinary systems containing constant amounts of nickel. The systems considered contain 0, 1, 2, 3, 5, 10 and 20 per cent nickel. The straight copper-tin system was reinvesti-gated in order to establish a foundation on which to build the remaining material. The 1 per cent nickel alloys studied give the relations existing in the region of the eutectoid transformation between the copper-tin system and the 2 per cent nickel copper-tin system which has been investigated in detail. The thorough examination of the latter system was made since 2 per cent of nickel is representative of the commercial additions to the cast bronzes and also because it is sufficient to produce

Jan 1, 1933

By K. A. Natarajan, I. Iwasaki

Platinum electrodes are not inert as often thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g, in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measure ments in water-oxygen, iron-water-oxygen, and manganese-water-oxygen systems. Stability relations between Fe++ and Fe (OH), and between Fe (OH), and Fe (OH), were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions. Platinum electrodes have often been used in the measurement of dissolved oxygen concentrations and of redox potentials (Eh) in a variety of fields, e.g., analytical chemistry,' corrosion," geology and mineralogy,,'' biology,"' sewage treatment,' * hydrometallurgy,"I" and flotation."la The effectiveness of Eh-pH diagrams, first reported by Pourbaix' in 1949, has contributed much towards the theoretical understanding of numerous problems encountered in the metallurgical industry. Not many references are available in the literature, however, wherein attempts have been made to confirm Eh-pH diagrams from experimental measurements. One reason might be that, in spite of the apparent simplicity of the electrochemical technique, the direct measurement of Eh involves complex practical problems.' Factors such as the purity of the solution, the type of electrodes used, the history of the indicator electrode, and the type of atmosphere (namely, oxidizing, reducing, or inert) do have effects on the measured Eh values. The influence of mixed potentials cannot be underestimated. The poisoning of platinum electrodes by organic and inorganic impurities present in the solution may lead to erratic results. Platinum, commonly thought to be an inert electrode material, is not really so, as attested by a number of previous investigators who advised caution concerning the anomalous behavior of platinum electrodes in various electrochemical measurements.'" In the present article, a few pertinent experiments related to Eh-pH measurements in systems of interest in the metallurgical and water pollution fields are described in an attempt to correlate such information with what is already known, especially in the electrochemical literature. Iron-water and manganese-water systems were selected with a view of studying the correspondence between experimentally observed and theoretically established equilibrium lines. The work included an investigation of the behavior of platinum electrodes with respect to pretreatment and adsorption characteristics, the measurement of dissolved oxygen concentrations and their relation to Eh, the determination of the electrode potential of the ferric-ferrous couple at different pH, and the measurement of oxidation potentials in iron-manganese leaching systems. Experimental Procedure A rotating platinum electrode was used in many of the measurements to study the effect of rotation on measured Eh values. The electrode made by the Pine Instrument Co. consisted of a stainless steel rod with a platinum disk soldered to the end. It was covered with a Teflon insulation along the sides, so that only the circular tip of the electrode was exposed to the solution. Prior to its use, the platinum surface was brightened on a metallurgical polishing wheel with alumina as an abrasive, unless specified otherwise. The electrode was rotated with a Sargent cone-drive motor at 350 rpm. The contact of the electrode with the external circuit was made by filling a notch at the top of the stainless steel shaft with mercury and by dipping a copper wire into the mercury pool. The performance of the rotating platinum electrode was compared with the performances of a Beckman platinum button electrode and a platinum wire electrode. All the potentials were measured with respect to a saturated calomel electrode. A saturated KC1-agar bridge was used to minimize the liquid junction potential. A Beckman Zeromatic pH meter together with a Beck-man electrode switch was used to measure both the Eh and pH. A double-walled, all-Pyrex jar with a capacity of about 1 liter and themostated by circulating water of constant temperature was used for a reaction cell. Four equally spaced ports in the cover provided access for a glass electrode, a salt bridge connecting the saturated calomel electrode, a dispersion tube for bubbling gases into the cell solution, inlet and outlet tubes for passing the desired gases over the solution, and a graduated burette for introducing reagents from outside. The rotating platinum electrode was inserted through an opening in the top-center of the cover, and a positive gas pressure was maintained inside the cell to prevent air from entering into the cell compartment. A magnetic stirrer was used to mix the solution inside. For the determination of dissolved oxygen in the test solutions, the polarographic techniquex was used.

Jan 1, 1971

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy' presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. 'References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,' and Carter et a1.' treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy's law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By R. E. McNulty, R. D. Heidenreich, C. H. Gerould

TIIE electron microscope techniques and their application to magnesium alloys that are to be discussed in this paper are the result of research at The Dow Chemical Co. over the past three years. The view- point underlying the work is not wholly metallurgical, but has evolved through a variety of problems related to the physics and chemistry of surfaces. It can be said that the interest and stimulus were closely associated with a desire to employ effectively the electron microscope in research concerning the properties of solids as related to their physical structure. Only a portion of this work will be described here, and, consequently, many points of interest and debate are of necessity either only briefly recognized or are completely omitted. As has been pointed out by Desch,1 a great deal of the knowledge of the structure of metals has been obtained through microscopic studies of the surfaces of metallic specimens prepared in a particular manner. This information, when added to that obtained by means of thermal, electrical, X-ray, dilatometric and other methods, has been of great value both from a theoretical and a practical view- point. With the introduction of new instruments such as the electron diffraction camera and the electron microscope, it would be expected that still more information could be obtained. These two instruments have in many instances been very effective when directed toward the investigation of metallic surfaces, provided the proper methods of surface preparation were employed. Experience shows that the problems of surface preparation greatly limit the general application of these instruments to metallographic studies. It was found necessary to discard the standard metallographic procedures in applying the electron microscope to magnesium alloys and to work out new methods, which were required to satisfy certain conditions. These methods are unique to magnesium only in the specific chemical reactions occurring during etching. The presentation of the methods and results will be ordered as follows: I. Electron Microscopy of Surfaces. 2. Surface Preparation of Magnesium Alloys. 3. Discussion of Microstructures. a. Pure Magnesium and Single-crystal Studies. b. Types of Precipitation. c. Some Common Structures. d. Special Micrographs and Techniques. e. Structure of Mg-A1 Solid Solutions. 4. Correlation of "Fine Structure" with Corrosion Behavior of Magnesium Alloys.

Jan 1, 1946

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By M. J. Richards, A. Szirmae, G. R. Speich

The formation of austenite from ferrite, ferrite plus retastable carbide, spheroidite, and pearlite has been studied in a series of irons, Fe-C alloys, and plain-carbon steels using fast heating techniques. In the absence of carbide, austenite nucleates at ferrite/ferrite grain boundaries; nucleation is followed by the rapid growth characteristic of a massive transfornation. The trarnsformation occurs at 950°C at heating rates of 106º C per sec and cannot be suppressed. Metastable carbide dissolves before austenite forms and does not influence the transformation kinetics. For spheroidite structures, austenite nucleates preferentially at the jinction between carbides and ferrite grain boundaries. Growth from these centers proceeds until the carbide is completely enveloped; subsequent growth occurs by carbon diffusion through the austenite envelope. For pearlite structures, austenite nucleates preferentially at pearlite colony intersections. Carbide la)?zellae dissolve at the advancing austenite interface but complete solution of carbide does not occur; the residtial carbide is eventually dissolvled or spheroid-ized depending on the carbon cuntent. The magnitude and temperature dependence of the austenite growth rate into Fe-C pearlite when incomplete carbide dissolution is assumed are satisfactorily explained by an approximate colume diffusion model. The impurities present in plain-carbon steel reduce the growth rate of austenite in comparison to that jound in an Fe-C alloy. The formation of austenite has been studied in much less detail than the decomposition of austenite. This is primarily a result of the importance of harden-ability in determining the mechanical properties of steel. Recently, more interest in the kinetics of austenite formation has resulted from the discovery by Grange1 that rapid heating techniques strengthen steel by refining the austenite grain size. Although the strengthening effect is not large, it is accompanied by no loss in ductility. In addition, interest continues in rapid heat treatment of low-carbon steel sheet for tin plate applications.2,3 Among the few systematic studies of austenite formation are the early work of Roberts and Mehl4 on formation of austenite from pearlite and recent work of Molinder5 and of Judd and paxton6 on formation of austenite from spheroidite. Also, Boedtker and Duwez7 and Haworth and paar8 have recently studied the formation of austenite from ferrite in relatively pure iron, Kidin et al.9,10 have studied the formation of austenite in 8 pct Cr steels, and Paxton has recently discussed various aspects of austenite formation in steels." The present work was undertaken to determine the kinetics of austenite formation for a variety of starting structures including ferrite, ferrite plus metastable carbide, ferrite plus spheroidal cementite, and ferrite plus pearlitic cementite. Emphasis was placed on determining the active sites for austenite nucleation, determining the temperature and time range of austenite formation, and in the case of pearlite a careful study of the growth rate of austenite was made in the absence and presence of impurities. By using a variety of heating techniques including laser-pulse heating, it has been possible to study austenite formation in an isothermal fashion over a wide range of temperatures. EXPERIMENTAL PROCEDURE The alloys studied in the present work are a zone-refined iron with 4 pprn C, an Fe-C alloy with 130 pprn C, 2 Fe-C alloys with 0.77 and 0.96 wt pct C, and a plain carbon steel with 0.96 wt pct C. The zone-refined iron and Fe-C alloys contained 60 pprn and 200 pprn total substitutional impurities, respectively. The plain carbon steel contained 2400 pprn Si, 2000 pprn Mn, and 900 pprn Cr. Various heat treatments were given to these alloys to produce different starting structures of equiaxed ferrite, ferrite plus metastable carbide, fine pearlite, and spheroidite. These heat treatments are given in Table I. A wide range of heating rates were employed in this work because many of the reactions occur so quickly at temperatures in the austenite range that they are completed during the initial heating cycle unless very fast heating rates are used. Essentially the same heating techniques employed by Speich et a1.12 and Speich and Fisher13 were used in this work. For time intervals of 2 sec to 20 hr, simple hand immersion of 0.010-in. thick specimens in a Pb-Bi bath was employed. These specimens were quenched in a 10 pct NaC1, 2 pct NaOH aqueous bath. For time intervals of 100 m-sec to 2 sec, an automatic dunking and quenching device was employed with 0.002-in. thick specimens. Again, liquid Pb-Bi baths were used for a heating medium but now helium gas quenching was employed. For time intervals of 2 to 100 m-sec a laser heating device was employed with 0.002-in. thick specimens; a helium plus fine water-droplet spray was now used for quenching. Additional information on heating times shorter than 2 m-sec was obtained by study of the zones around the centrally heated laser spot. Here diffusion of heat from the centrally heated zone raises the temperature of the specimen locally to all temperatures between ambient and the peak temperature, but for times of the order of microseconds. All the heat-treated specimens were examined by

Jan 1, 1970

By Henry Rawdon

THE structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i.e., manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the inclosures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in "pure" metals in general (etching pits).

Jan 9, 1917

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,&apos; and his experiments have been described and summarized by Richards.&apos; White&apos;s contributions seem to have passed unnoticed by Fahrenwald,2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,&apos; USSR; Anselm and Grunder,&apos;, Germany: and Rose and Evans." Great Britain. Subcritical and Supercritical Speeds: In the formula of the critical speed given in the textbooks of mineral dressing, no factor indicating the coefficient of friction is generally included. If this factor = 1.0, which is equivalent to grinding conditions in a mill provided with heavily ribbed lining, the formula of the critical speed holds as such and grinding is possible at subcritical speeds only. In a mill equipped with a smooth or relatively smooth lining, the numerical value of the friction factor in the denominator of the formula becomes <1.0, indicating that grinding at supercritical speeds should be possible in such mills. It has been recently shown by the author&apos; that a wide supercritical speed range will become available for grinding—and especially for fine grinding—if the basic conditions within the mill have been selected properly. Mathematical analysis of mill dynamics at supercritical speeds&apos; has indicated that the mill speed may be increased if: 1) total mass of grinding medium decreases, 2) mass of the individual grinding piece increases, and 3) the coefficient of friction between the outer layer of medium and the mill lining decreases. It is obvious that the mass of the individual grinding piece will be affected by its shape and by its specific gravity. The coefficient of friction decreases with: 1) increasing smoothness of liner surface, 2) increasing roundness of the grinding piece, 3) increasing fineness of material to be ground, 4) decreasing pulp density, and 5) decreasing hardness (abrasiveness) of the mineral to be ground. In a mill equipped with heavily ribbed lining, practically no size reduction will take place between the lining and the outer layer of tumbling medium, because slippage is prevented. In the overwhelming majority of today&apos;s mills the grinding accomplished is by virtue of cataracting and/or cascading media with some action within the tumbling charge. Sub-critical speeds only can be applied. In grate-type or peripheral discharge mills equipped with a smooth lining a tumbling load of any kind of common medium occupying about 50 pct of mill volume will behave in such a way that practically no slippage will take place. This has been verified in experiments run by the author in the laboratory and in pilot plant mills&apos; equipped with smooth lining. Again, the operation is limited to the subcritical range. In a mill with a smooth lining, grinding will be possible either at subcritical speeds or within a wide supercritical speed range as soon as the basic requirements for a desired speed are fulfilled. In a mill operated at supercritical speed, any point on the liner surface proceeds at a speed greater than that indicated by the formula of the critical speed, while any grinding piece situated in the outer layer of the medium against the lining proceeds in the same direction at a speed less than that indicated by the critical speed. This speed difference produces a very effective attrition grinding zone between the liner surface and the outer layer of the medium. The share of attrition grinding of the total grinding accomplished increases rapidly with increasing speed in the supercritical speed range. The smooth surface of the mill lining may be well illustrated by the surface of a bucking board. The outer ball layer may be similarly represented by the lower surface of a muller. If the bucking board, the material to be ground, and the muller all proceed in the same direction at the same speed, no grinding will result. This is the general situation in the mills of today. If, however, the muller is pulled with respect to the board, moving or stationary, grinding will be accomplished effectively. Although grinding in today&apos;s mills is primarily the result of cataracting and/or cascading media, the principal place of grinding at high supercritical speeds will be the attrition zone.&apos; In the mineral dressing laboratory of the State Institute for Technical Research. Helsinki, Finland, large quantities of different ores have been ground in a pilot plant ball mill (3x3 ft) at a top speed about 230 pct of the critical. With the same mill, theoretical investigations concerning the grinding characteristics of ball mills equipped with a smooth lining have been carried out up to the speed of 313 pct&apos; of the critical. With a smaller mill, the grinding characteristics with a variety of grinding media have been investigated at speeds up to 2000 pct of the

Jan 1, 1959

By AIME AIME

ANOTHER meeting of the Institute has passed into history and it fully sustained the reputation of the Institute as a live organization of the men, and nowadays the women, concerned with the mineral . ? industries and those working therein. The field meetings of, the 1nstitute are cine of its pleasantest and most valuable features. As Dr. Raymond used to say, ((It is good for a mining engineer once in a while to see a mine" and these meetings bring back to the mines those who, through progress into higher executive positions, have come to visit them infrequently, at the same time that they give opportunity for the .younger men to see regions and mines aside from those in which they are then working. This, and the formal and&apos; informal interchange of information resulting,, is of the greatest professional value to all, while the meeting of old and making of new friends causes each meeting to be notable in turn. This year&apos;s meeting at Salt Lake City was one of the largest that has been held outside of. New York City; 470 members and guests registered while many more were present at the sessions without attending to this formality. &apos;

Jan 1, 1925

By C. K. Leith

GENERAL GEOLOGY OF THE LAKE SUPERIOR IRON-BEARING AND COPPER-BEARING SERIES. THE geology of the Lake Superior region is of general interest, both from an economic and a scientific standpoint. The presence of large and rich iron- and copper-deposits has made a knowledge of the geology of the region necessary for purposes of exploitation and exploration. The ores of the region are contained in rocks of pre-Cambrian age, &apos;pith for most of the country up to recent years have usually been referred to as « crystalline schists " or " crystalline complex;" and regarded principally as metamorphosed basement-unit upon which the sedimentary rocks, beginning with the Paleozoic, were laid down. In the Lake Superior re¬gion this pre-Cambrian complex presents an unusual variety of rocks with determinable relations. It has been possible, with the large expenditures which-the magnitude of the iron-mining industry warrants, to work out their stratigraphy to a larger extent than has been possible in almost any other area of pre-Cambrian rocks. The real complexity of Lake Superior geology, the confusion of names and the multiplicity of reports covering small parts of the region, are such that interested persons, other than. geologists directly engaged in the work, may well hesitate to attempt to comprehend the geology of the region as a whole. The following paper is a somewhat elementary outline of the geology of the Lake Superior region with special reference to new developments not yet covered in published reports. Geological information concerning the region has been gath¬ered by mining companies, and by the geological surveys of Michigan, Wisconsin, Minnesota, Ontario, Canada, and the United States.. Perhaps in no other part of the country have the mining men themselves spent such large sums in purely geological work. This has made possible the publication of ,reports and maps by the State and Government surveys in much less time and at far less cost than would have been otherwise possible. The. U. S. Geological Survey is the only organization which has covered all of the region on the United &apos;States side of the boundary, and as its reports include the in¬formation gathered by the mining companies and State organi

Mar 1, 1905

Jan 1, 1902