Search Documents

By K. K. Clark

Excessive injection pressures in water injection wells may create deeply penetrating fractures, or may open up existing reservoir fractures. If these fractures are oriented toward offset producing wells, oil recovery at injected water breakthrough and ultimate recovery will be impaired. A method of calculating fracture lengths from pressure fall-off test data is presented. The method is based on a linear flow model that simulates conditions present during the early-time period after shutting in an injection well. Fracture lengths can be calculated directly if formation permeability is known. A graphical technique is presented that provides fracture lengths based on permeabilities calculated from normal fall-off tests, where those permeabilities are adjusted for flow geometry. Test data from four injection wells and results obtained from applying the method to these wells are discussed. Introduction Rates of water injection into nonstimulated wells in low permeability reservoirs frequently fall below economically desirable levels. Therefore, some form of stimulation such as hydraulic fracturing often is performed on these wells. Usually these fractures penetrate a short distance from the well — short as compared with interwell spacing — and therefore should not create problems of water channeling to offset producing wells. In the past, some operators have been tempted to increase injection pressures continually to maintain a specified injection rate. But pressures cannot be increased indefinitely. Field data indicate that continued injection above fracture opening pressure can cause excessively long fractures to approach between well distances. If these long fractures intersect or closely approach offset producing wells, premature water breakthrough can result. It is difficult to seal effectively these fractures by various workover procedures after premature water breakthrough has occurred. This paper describes testing procedures that are potentially capable of detecting premature water breakthrough before it occurs. Knowledge of fracture lengths and fracture opening pressures can assist field engineers in selecting optimum operating conditions for water injection wells. Fracture lengths should be calculated from pressure fall-off tests on injection wells, and maximum permissible iniection pressures should be determined from step-rate injectivity tests. Equipped with this information, the field engineer is in a better position to recommend for a particular injection well the optimum operating conditions that will lessen the chances of channeling to offset producers. Historically, pressure transient tests have been conducted primarily on producing wells and analysis procedures have been based on radial flow concepts. Several authors have suggested that these same procedures be applied to tests conducted on water injection wells. This application is justified for wells that are not connected to extensive fracture systems. However, if the formation is severely fractured, the interpretation methods must be modified. Several authors have presented the pressure response of various systems that are intended to simulate reservoir conditions. A paper by Russell and Truitt* on vertically fractured svstems is probablv the most useful from the standpoint bf the fieid engineer. Russell and Truitt presented the pressure-vs-time behavior of a well connected to vertical fractures with various fixed lengths. Their permeability adjustment technique is used in this paper to refine methods of calculating fracture length and interwell permeability. Theory and Definitions Three flow-system geometries are considered in analyzing injection well test data. These various geometries are applicable during specific time intervals of transient pressure tests. Schematic drawings of the flow models, and the time intervals over which they are applicable, are shown in Fig. 1 in the chronological order that they are applied to the pressure response of water injection wells in fractured formations. The very early response is simulated by an infinite linear system as shown in Fig. 1A. This representation permits the calculation of matrix surface area exposed to the fracture. The model shown in Fig. 1B is identical with the one studied by Russell and Truitt. They evaluated the transient pressure response of this vertically fractured system by finite difference techniques. The results were presented as tabulations of dimensionless pressure drop functions for a range of fracture lengths. A semilog plot of these data shows that the apparent matrix permeability can be related to the true matrix permeability by a simple exponential function. Their adjustment factor is used in this paper to improve the accuracy of matrix-permeability and fracture-length calculations.

Jan 1, 1969

By David Scott

THE MOGOLLON mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately. $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent, of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. LOCATION AND TOPOGRAPHY The town of Mogollon is 75 mi. (121 km.) by a poorly located highway from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western-slope of the Mogollon Range. The main canyons run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the

Jan 2, 1920

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By George S. Rice

Those who for the first time see, at a mine, a great hole caused by subsidence; or, going underground, see an extensive fall of roof or hanging wall are apt to regard such an occurrence as an accident and not a normal condition of exhaustive mining. Moreover, the public is inclined to believe that a cave or subsidence of the surface is the result of carelcssness in mining or the rapacity of the mine operators in "robbing pillars," a tern too loosely used in descriptions of coal mining. This belief is fostered by the common-law requirement that an owner of the surface or of surface improvements is entitled to full support of the surface. Court decisions have upheld this law even when that owner has sold or leased the underlying mineral, unless a clause in the sale or lease contract exempts the mining company from paying the owner of the surface for damages that may result from mining. Another reason for this belief is the earlier practice (which is still extensively followed in this country) of leaving all coal pillars unmined, except as they have been thinned by so-called robbing; by not extracting the pillars, the surface may be supported by them for years, perhaps for generations. Inasmuch as the practice of leaving permanently in the mines from one-third to one-half of the mineral is wrong, with respect to conservation of a national resource, it behooves the mining engineers to assemble data and disseminate information on the subject, pointing out that subsidence must follow complete extraction, unless expensive methods of back-filling are employed, such as are used in Germany and France. These methods inevitably increase the cost of mining and the price of the mineral produced. It is popular to speak of "waste in mining" without a realization that much so-called wasting is unavoidable unless subsidence is accepted and provision made therefor where the surface is valuable, or else the only present known alternative of hydraulically placing sand or crushed stone filling in the excavations, at an increased cost of the mineral product to the consumer.

Jan 1, 1923

By Max Roesler

Page I. Introduction........................... 78 Location.......................... 78 Scope of Work and Acknowledgments.............. 79 History and Mining...................... 80 I1. Topography and its Interpretation................. 80 III. Petrology............................ 82 Sedimentary Rocks...................... 82 Description....................... 82 Age.......................... 84 Igneous Rocks........................ 85 Diabasic Rocks..................... 86 Dioritic Rocks...................... 87 Granitic Rocks...................... 88 Later Dike Rocks.................... 88 IV. Areal Geology.......................... 88 Rock Types Found in the District............... 88 Distribution of the Various Rock Types............. 89 Surface Distribution................... 89 Vertical Distribution................... 90 Causes of Present Areal and Vertical Distribution of the Various Rock Types..................... 91 Faulting...................... 91 Magmatic Differenti~tion............... 91 Tilting........................ 95 Erosion....................... 96 V. General Description of Ore Deposits................ 96 Nature of Ore ........................ 96 Shap~ and Size of Orebodies.................. 96 Geologic Position....................... 97 Mineralogy......................... 98 Distribution....................... 98 Interpretation...................... 99 Superficial Alteration................... 102 VI. Genesis of the Ore Deposits.................... 104 Previous Theories...................... 104 J. P. Kimball...................... 104

Jan 1, 1917

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By Max Mason

In 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which automatically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1929

By Charles W. Eichrodt

So much has already been wimitten on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place. Effects of Excavation on Ground Movement Broadly, the effects of excavations on the overhead or adjacent ground can be classified under three headings, as follows: 1. Ground movements due to excavations made from surface only, such as those made in opencasts where no excavations underlie them. The stability and strength of the ground to resist movement must determine the slopes. 2. Ground movements due to underground excavations only; i. e., where the surface is not removed. 3. Ground movements due to a combination of both; i. e., from excavations taking place from the surface for the purpose of stripping an orebody and recovery of the ore to a certain horizon combined with excavations being carried out below, at the same time, for the winning of the ore below the horizon at which mining by stripping or opencasting under the specific conditions is no longer economical. Nos. 1 and 2 represent independent and distinct problems and No. 3 is a combination, which presents results much more difficult of explanation. The accompanying plans and sections give examples of what has occurred under the three conditions. Unfortunately, the class of ground is not exactly the same in them all, but the difference is not greater than is generally encountered over districts of equal area. Excavations from Surface To illustrate No. 1 three cross-sections are shown, of excavations made for the stripping and excavation from three different orebodies

Jan 1, 1930

By S. B. Christy

The practice of the cyanide-process of gold-extraction has brought to light many important contradictions of familiar chemical analogies, which still obscure both the theory and the practice of the art with distinctions subtler and more difficult to make or follow than those which delighted the heart of the old-time metaphysician. Yet Nature herself has drawn these distinctions; and if we hope to succeed in this modern search for the Golden Fleece, we must be able to follow her through the winding labyrinth. There are so many phases of this question that I shall attempt to touch on only one of them at this time, but it is one that lies at the root of many others. In reviewing my paper on " The Solution and Precipitation of Cyanide of Gold,"* Mr. E. B. Wilson contends† that" in the solution of gold by means of alkaline cyanides the various reactions are determined, as to their order and intensity, by the relative position of the elements concerned in the electro-chemical series, or series of voltaic tension." In a modified form this statement is probably true. That is to say, the difference of electrical potential in any closed electrical circuit determines the nature of the reactions which ensue. But the matter is not so simple as Mr. Wilson assumes. Recent investigations show that the order of the metals in the electro-chemical series depends not only on the nature of the elements themselves, but also on the chemical composition of the solution in which they are placed; its degree of concentration; its temperature; and, in the case of gases, on the pressure. Unless all these conditions are taken into account, inferences drawn from the electro-chemical series are likely to prove more

Jan 1, 1901

By Herbert Hoover

THE desire of the engineers over the last few years, growing out of their contact with public affairs, that this Institute should take a wider vision than the narrower field of technology and should apply its skill to the development of civic problems which must lay in their foundation on engineering, has led to this discussion today. Some of us in San Francisco, in discussing this question of the relation of the engineers to civic problems, raised the question as to whether or not in this national emergency it was not the duty of the Mining Engineers to bring, forward their combined skill and knowledge and experience to bear upon the problems of the coal industry. This industry, considered as a whole, is one of the worst functioning industries in the United States. It is equipped with capital, with machinery, plants and labor to a peak load at least 20 per cent. above the average necessity. This peak load, therefore, involves the use of probably 100,000 men diverted from other productive industries; it involves an intermittency of employment through its whole personnel that results not only in a long train of human woe, but results also in a higher cost of coal -to the general public. The problem of whether the industry can, by any device, be cured or even partially cured of its intermittency, is solely an engineering problem. It is therefore an apropos problem for this Institute. Your President and myself and others thought that we could best develop this discussion by calling upon men of large experience in the particular branches of the soft coal industry, to bring the facts in front of this general committee, with a view to an exhaustive discussion and perhaps subsequently the appointment of a committee to formulate those facts and such remedies as may be developed into a report that would be of constructive value.

Jan 3, 1920

By T. W. Bossert

MELTING is the initial step in the fabricating of all aluminum and aluminum-alloy products. Its function may be considered as threefold: to improve the metal quality, to adjust the composition, and to change the form to that required for subsequent fabrication. Because the melting operation is generally somewhat removed from the final product fabrication, its importance is frequently overlooked. Melting equipment and melting procedures can reflect materially on fabricating procedures as well as on quality and cost of final product. The selection of equipment and the establishment and control of melting procedures, therefore, should be given careful consideration. It is the purpose of this paper to present the various factors that should be considered in establishing melting procedures and in selecting melting equipment. Certain of these are the result of the inherent characteristics of aluminum and can be treated rather specifically. Others depend on the particular production requirements and hence will have to be considered more generally. This paper is intended to cover only the melting of solids, as differentiated from fines, such as borings, turnings, and sawdust. The melting of fines, in many respects, is a subject that should be treated by itself, and practices for melting fines are by no means as standardized as are those for melting solids. The melting of fines is today the subject of considerable developmental interest; hence practices discussed today may soon be replaced by new or improved ones. CHARACTERISTICS OF THE METAL THAT AFFECT MELTING Aluminum and aluminum alloys possess several inherent characteristics that affect the melting problem. Of the physical properties, density, heat content, thermal conductivity, emissivity, and melting temperatures are important because of their effect on equipment design. A list of such properties for commercially pure aluminum is given in Table r, compared with similar properties for iron and copper. The low density of aluminum as well as of the aluminum alloys is of material advantage in the design of melting equipment, in that such equipment can be considerably lighter than similar equipment for handling the heavier metals. The density, however, particularly of the molten metal, is not greatly different from that of the oxides and other nonmetallic materials that develop or become part of the melt during the melting process. Separation of such nonmetallics is not as rapid a process as with some of the other metals, and consideration of this must be made in establishing melting procedures. Sufficient holding time to permit such materials to separate out and, in some cases, fluxing treatments to aid the separation, are required. Since some of these nonmetallics settle to the bottom of the melt, provision should also be

Jan 1, 1946

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By Earle Schumacher

COPPER-CALCIUM alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiens1 have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1929

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By Paul R. Dingess, Edward H. Hare, Douglas C. Brockie

Mining in the Tri-State district of Missouri, Kansas, and Oklahoma has been nearly continuous from about 1848 until the present day, although the major activity was from about 1880 to 1955. The district, which has produced over $2 billion in zinc and lead concentrates, ranks as one of the greatest mining districts in the world. Unlike other Mississippi Valleytype deposits in the United States, which occur in Cambrian and Ordovician limestones and dolomites, the Tri-State district ores occur in Mississippian limestones containing abundant chert. Zinc is 5 to 6 times more abundant than lead. In the Picher Field, the principal sub-district which has accounted for 61 percent of the total district production, most of the ore has been mined from the single horizon, M bed. Most ore bodies, other than those of the "Sheet Ground" or blanket-type, are in large, essentially flat-lying breccia zones and have a definite mineral zonal pattern. An irregular, generally elongated central dolomitic core is surrounded progressively outward by the main ore run, the jasperoid zone, the muddy or shaly and bouldery zone, the sparry calcite limestone zone, and the fossiliferous, dominantly crinoidal, limestone zone. Some of the zones may be absent or nearly so and may overlap to some extent with an adjacent zone. Although the district has been studied by many authors, much controversy still exists about such items as genesis, paragenesis, and time of emplacement. These subjects are discussed in the paper.

Jan 1, 1968

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By John H. G. Monypenny

The range of chromium content of stainless steel is, in most cases, included in the limits 11 to 14 per cent., or the middle part of the range, 9 to 16 per cent., specified by the discoverer. For some time after the steel was produced commercially, the carbon content was about 0.3 to 0.4 per cent. and occasionally higher; only rarely was material with 0.25 per cent. carbon or less produced. The reason for this is obvious from the nature of the alloys of chromium available for making such steels; as the lowest carbon content generally available was about 1 per cent., and this in conjunction with a chromium content of about 60 per cent., the production of a 12-per cent. chromium steel with less than 0.25 to 0.30 per cent. carbon was impossible. The advent, on a reasonable commercial scale, of carbonless ferrochromium has modified this condition, however, so that for the last three years stainless material containing 0.1 per cent. or less carbon and the normal amount of chromium has been on the market. As far as the author is aware, the material was first made on a commercial scale by the firm with which he is associated in June, 1920, when a 5- or 6-ton cast of material containing 0.07 per cent. carbon and 11.7 per cent. chromium was made and cast into 12-in. ingots. The necessity for using a totally different raw material, carbonless ferrochromium, instead of the ordinary low-carbon ferro (0.6 to 1.0 per cent. carbon) has led to the idea that stainless iron is a quite distinct product and quite different from stainless steel. While this may be true from a commercial aspect, it is wrong metallurgically. The name stainless iron is unfortunate as the material is a very mild stainless steel and forms the lowest carbon member of a series of steels of continuously varying content which are, in many respccts, the counterpart of the series of ordinary carbon steels ranging from "dead soft" to tool steels. In an article on stainless steel in the Journal of the Society of Chemical Industry, November, 1920, the author said "Just as in the far-off days 'steel' was regarded as a hard product of iron, and little or no attempt was made to grade it into harder or softer varieties, so at present stainless

Jan 1, 1924

By E. L. Claridge, K. S. Lee

Areal sweep efficiency of oil displacement by enhanced-viscosity water exhibiting pseudoplastic behavior was measured in a Hele-Shaw model representing one-quarter of a five-spot pattern. The pseudoplasticity of polymer solutions and the velocity distribution in the five-spot pattern produced a condition under which the mobility ratio between the displacing and the displaced fluid could not be assigned a single value. Instead, the movement of the displacement front is governed by local mobility ratios which are also time dependent. The areal sweep at breakthrough with polymer solutions was poorer than the sweep obtained with Newtonian fluids of comparable viscosity. However, the areal sweep at 1 PV throughput was greatly improved as compared to flood water without polymer. It was also demonstrated that, even after the oil-cut had declined to a low value during a regular waterflood, switching to polymer flood efficiently swept out the oil remaining in the model. INTRODUCTION The behavior of fluid displacements in isotropic porous media for various patterns of injection and production wells has been extensively investigated.1-7 These investigations all concerned Newtonian fluids, i.e., the viscosity of each fluid was constant regardless of flow rate. The generally unfavorable influence on areal sweep efficiency of higher mobility of the displacing fluid as compared to the mobility of the displaced fluid has been established for both miscible and immiscible fluids. The principle was also established that a close correspondence exists between miscible and immiscible flood front behavior,2, 3 although oil recovery in a waterflood at unfavorable mobility ratio may be less than that observed in a miscible displacement at the same mobility ratio. This is true even when oil recovery is expressed on the basis of movable oil. The reason is that oil saturation only slowly achieves its final value behind the water-flood front in accordance with the Buckley-Leverett8 simultaneous flow relations. It is convenient to use miscible displacements for laboratory simulation of waterflood frontal advance since the interfacial tension forces which are negligible in proportion to viscous forces on a reservoir scale9 are thus made nonoperative in the laboratory model. For miscible displacements, the Hele-Shaw type of model adequately represents a porous medium so long as the appropriate scaling rules5-10 are observed in its design and operation. During simulation of waterflood front behavior in the laboratory by using miscible displacements, the behavior of connate water may ordinarily be disregarded since it is usually indistinguishable from flood water in this process. However, when the flood water is deliberately thickened to improve the mobility ratio between water and oil. the effect on the sweep efficiency due to generation of a connate water bank during the process must be considered. In a uniform porous medium, such a bank is generated11 and efficiently displaced by injection of thickened water.l2 The oil originally in-place at the start of the waterflood is then displaced by connate water followed by thickened water. If the flood water must be thickened to obtain a favorable mobility ratio, the mobility of the oil phase is appreciably less than that of the connate water. Hence, the oil phase is inefficiently displaced by the connate water bank, and a considerable proportion of the oil comes in contact with and is displaced by the thickened waterflood front' A recent study 12 of five-spot displacements using miscible Newtonian fluids in which connate water banks of various sizes were simulated shows that, for connate water banks as large as 40 percent of 1 PV, major improvements in sweep efficiency resulted from use of a thickened

Jan 1, 1969

By O. W. Ellis

THE question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,1 Iwasé,2 Lobley and Jepson3 stand preeminent. SOLUBILITY OF . GASES IN. COPPER Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate-possibly 30° to 60° C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1928

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946