Search Documents

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By J. S. Fulton

THOSE who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangement, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartment septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries) ; portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. PHASES Of the many papers published on various phases of the Bessemer process, nearly 170 according to one bibliography, over go per cent were concerned with the metallurgical phase and less than 10 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to one of the causes of the Bessemer process. Is it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.O.b. mines, the output in 1948 was 1,-568,848 tons worth $19,756,738. Paradoxically, it seems in retrospect that the early failure of the American industry to meet foreign competition was due to the superior quality of our sedimentary clays in their natural state. Kaolin, of course, is the principal decomposition product of feldspars which originate in acidic igneous rocks such as granite, aplite, alaskite, granodiorite, quartz porphyry, etc. English china clays occur in residual deposits and before they can be marketed they have to be treated to remove accompanying quartz, mica, and other impurities. Notwithstanding the relatively crude methods employed, the final product is a beneficiated clay which is subject to a certain amount of technical control as to quality and uniformity. Although the naturally concentrated deposits in Georgia and South Carolina contain some of the finest crude white kaolin in the world, even it can be made better by suitable treatment. In recent years well over half of the high-grade china clay produced in the United States has been used in making paper. Some qualities of paper clays are still produced by the dry process, or air flotation, but the paper industry's specifications have grown so exacting that wet processing was adopted and more refined methods had to be perfected. Notwithstanding notable advances in clay-preparation technology during the past decade, or possibly because these advances have implemented and encouraged technologic changes in consuming industries, demand has grown for products of higher uniform quality than can be obtained from even the best natural deposits without rigidly controlled fractionation. Largely as a result of the wide adoption of machine coating for paper, the clay industry has been obliged not merely to eliminate virtually all mineral impurities but also to segregate the clay substance itself into narrow particle-size ranges. By extraordinary coordination of sales effort and production technology, several Georgia companies manage to market a wide variety of specialized joint products but the commercial success of many producers depends upon their mining only the best parts of their deposits and then skimming the cream of this almost pure clay in order to obtain a maximum yield of kaolinite finer than about 2 microns in maximum particle size and possessing low viscosity as well as the more familiar attributes of suitable color and brightness, or reflectance. To the casual visitor from another mineral industry, the kaolin mines and plants may appear to be

Jan 1, 1951

By C. H. Li, R. J. Stokes, T. S. Liu

Poly crystalline silver chloride specimens having different micro structures were prepared by extruding monocrystals or precompressed powder at varying temperatures. Extrusion at high temperature (370°C) produced a Fully recrystallized equi-axed material which was brittle and fractured by simple cleavage below its transition temperature (60°C for notched specimens). Extrusion at low temperatures (down to -196°C) produced an extremely tough cold-worked material with grains elongated in the extrusion direction. This material fractured below its transition temperature (which varied from —20" to —200°C) by an intergranular mode. It is concluded that cold work increases the resistance to transgranular cleavage. Fracture is then de-flected to propagate intergranularly ouer surfaces making an angle with the tensile axis with a corresponding improvement in notch toughness. This deflection is greater for extruded powder than for extruded monocrystals because of the extremely elongated grain shape. PREVIOUS work1,' on the fracture properties of fully recrystallized silver chloride under notch impact conditions has indicated that the fracture behavior is rather invariant. Thus polycrystalline materials originating from a number of sources ranging from relatively pure Harshaw single crystals to commercial-purity powder and prepared by hot extrusion at 370°C all fracture by simple cleavage with a ductile-brittle transition at 60°C, see Fig. 1. This behavior is also typical for fully annealed single crystals and appears to be fundamental to silver chloride for the particular loading conditions and notch configuration adopted. One way in which this characteristic fracture behavior can be modified is by the dispersion of alumina particles in the silver chloride matrix.' Then, particularly when the alumina particles are in the shape of spheres, the duc tile-brittle transition is much less sharply defined and occurs over a range of temperature, the transition temperature is lowered considerably and the fracture mode changes from simple cleavage to a fibrous or shear mode. The reason for this change is believed to be partly due to the nucleation of cavities in the region of the dispersed alumina particles which influences the state of stress locally and the distribution of plastic constraint at the root of the notch. It is emphasized however that this is not the sole factor responsible for the increase in toughness. In extruded materials it is reasonable to expect that the resultant grain size, texture, and the residual cold work will be influenced by the presence of a dispersed phase. The present experiments were initially designed to determine the extent to which cold work influenced the fundamental ductile-brittle transition temperature and fracture mode of silver chloride. They were stimulated by the discovery that silver chloride could be extruded at temperatures as low as -25°C when commercial-purity powder was used and as low as -196°C when single crystals were used. This working temperature was far below that previously used (370°C) and it was found that such extruded material was exceedingly tough. The reasons for the enhanced toughness and its relation to the previous work on silver chloride-alumina compacts will be discussed. EXPERIMENTAL PROCEDURE Materials Used. Two forms of silver chloride were used in this study: i) silver chloride powder

Jan 1, 1964

By J. R. Lucas, H. E. Rutherford

The primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this study was to determine experimentally the elastic wnstants of various rock specimens with the use of ultrasonic equipment. Elastic constants can definitely be determined quickly and accurately by ultrasonic investigation. With proper equipment there are indications that ultrasonic waves could be utilized in the detection of flaws, such as fractures and planes of weakness, measurement of thickness, and the study of structure of rock material. Ultrasonic principles have been applied in many industries for the purpose of determining the structural characteristics of various materials. The principal applications of interest here are detecting flaws, measuring thicknesses, and determining elastic constants. The main advantage of ultrasonic analysis is that it is nondestructive. It also has extreme sensitivity, high penetrability, good accuracy, rapid response, and the necessity to have access to only one side of the specimen. These various applications and advantages lead one to think that ultrasonic principles might be applied to rock material in situ for purposes of analyzing its structural characteristics. Therefore, the primary objective of this research was to evaluate the feasibility of ultrasonic testing for the purpose of analyzing the structure and properties of rock material. A secondary objective of this research was to determine experimentally the elastic constants of various rock specimens with the use of ultrasonic equipment. The term ultrasonics is given to that branch of acoustics dealing with periodic sounds whose fre- quencies are above the audible range or above approximately 15,.000 to 20,000 cps. The first practical production of this high frequency sound was made possible after World War I due to developments of electronically controlled sound wave sources. At the present, the maximum practically attainable ultrasonic frequency is approximately 1000 megacycles per sec. Sound waves of sufficiently high frequency can be made to travel in a beam with little spreading. Therefore, such a beam can explore a material and detect nonhomogeneities in it by reflection. This is the principle of the ultrasonic reflectoscope invented by F. A. Firestone' in 1942. An ultrasonic beam, on pulse-penetratink a solid material medium, produces an echo when it strikes a flaw which has different acoustical properties than the surrounding medium. This echo can be detected by the same transducer which sends out the original pulse. This principle is the basis of the important industrial techniques of nondestructive ultrasonic testing of metals and other solid material. Later developments in the field of ultrasonic testing of solid material have been mostly improvements in equipment and instrumentation. To date, most of the industrial applications of ultrasonic analysis of solid bodies have been in the aircraft, electrical, and nuclear energy fields on the nondestructive testing of metal. The one solid material similar somewhat to rock material, upon which some work has been done to apply ultrasonic testing techniques to study structural integrity, is concrete. Jones and Gatfield3 briefly summarize this work on concrete. Their basic conclusion was that the strength of concrete was a function of the change of the longitudinal sound wave velocity in the concrete. Only recently has any extensive study been made to apply ultrasonic testing techniques to rock material. Lutsch studied rock material by an ultrasonic pulse method to determine the extent and degree of fracture of rock faces. Lutsch states that the number of observed reflections is a measure of the degree of fracture and that only ultrasonic waves are able to detect fractured zones subjected to high pressure. Suzuki, Sasaki, and Siohara5 studied the characteristics of the sonic wave in rock for propagation over a wide range of wave lengths. They indicated that, in rock, the propagation constant and attenuation of the

Jan 1, 1962

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of green- sand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of green- sand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace- element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield ( 1922) does not mention base-exchange; however, the base ex-

Jan 1, 1975

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

By Dirk A. Benham, William A. Warfield

INTRODUCTION Whenever a mine operator is faced with a decision between various mining methods or even equipment selection, he must be assured that his decision will have a positive effect on his economic operating goals. For instance, if a mine operator has a choice of using an LHD mining system or a slusher mining system, then his decision to use either must not only fit within the operational limitations of the mining plan (such as production requirements, physical features of the ore body, mine plant facilities, manpower requirements, etc.), but also assure that the ore is being extracted at the least possible cost. To aid in his decision making process, the operator will commonly compare acquisition costs, operating costs, maintenance costs, and the operational advantages and disadvantages of each system in addition to considering his personal observations and feelings. A decision to select a mining system using only those criteria aforementioned will not necessarily lead the operator down the path to maximizing profits. In addition, the operator should also compare the economic effects of each system upon the overall mining operation. A relatively simple method for determining the economic effects is to calculate and compare the break-even grades for each system under consideration. By implementing such an analysis, the operator can now select a mining system which can operate within the limits of the mining plan as well as extract the ores at the least possible cost, thus yielding maximum profits. This paper will present the geologic and physical conditions of a mine being operated by the Hypothetical Mining Company in the Grants Mineral District. An LHD and Blusher mining system are under consideration and are compared by examining operating costs, equipment availability, and the conventional operational advantages and disadvantages of each. Finally, the economic effects of each system upon the overall mine's operation are compared by utilizing break-even grade analysis. DESCRIPTION AND MINING METHODS The Hypothetical Mining Company has located an ore body in the Grants Mineral District. After extensive surface exploration drilling and cost considerations are evaluated, it is decided to open a mine. The following tasks must now be performed: 1. outline ore body and it's basic characteristics, 2. look at mining methods currently in use in the area, and 3. determine mining techniques and methods for exploitation of the ore body. For the sake of argument, the newly discovered ore body is located towards the western edge of the Grants Mineral Belt. The host rock for uranium mineralization is the Westwater Member of the Morrison Formation. The Westwater Canyon sands are overlain by the Brushy Basin Member of the Morrison Formation and underlain by the Recapture Member, all of Jurassic Age. Westwater Canyon sandstone is a fine to very course grained subarkosic sand with interbedded green and red mudstone. The Brushy Basin Member consists predominantly of greenish-gray mudstones and contains thin lenses of sandstone and a few thin beds of limestone. The Recapture Member consists of alternating thin beds of reddish brown, grayish red, and light gray sandstone and siltstone. The Recapture interfingers with the Cowsprings Sandstone in the area of the mine. The mineralization is based on the groundwater flow within the Morrison Formation. Primary ore distribution is based on three basic parameters: ore migration in a geochemical cell, lenticular mudstone interbedding, and enrichment along fault zones. In areas where two fault systems intersect, ore thicknesses of up to 30 m (100 ft.) are encountered. In those areas where the ore is well defined and thicknesses facilitate full face mining, the mining methods are determined more by ground or operating conditions, equipment availability, and access to working areas than they are in the fringe areas of the ore body where grade control is more important and split-shooting and break-even grade determines the mining technique. If a modified room-and-pillar mining method using systematic development is selected, better control of the ventilation, equipment utilization, and mining plan can be obtained. Figure I shows a typical mining area where the ore is thick,

Jan 1, 1982

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

The authors of T.P. 4179 have conducted a large number of experimental water floods, and the data are reported in a very clear manner. These data show significant variations of residual oil saturation with changes in wettability, interfacial tension, flooding rate, and oil-water viscosity ratio. Furthermore, some of the data obtained cover a range of variables not previously reported in the literature. It is our opinion that at least some of the observed variation in oil recovery can be obtained only in floods made under conditions identical with those used by the authors. There are other systems which may be said to have the same wettability, but which exhibit an entirely different qualitative dependence of oil recovery on the experimental variables. In this regard, we would like to direct attention to several items which we feel are not given sufficient consideration in the paper. The first of these items has to do with wetting equilibrium. A survey of the current literature will reveal that little is known, and even less is understood, about wetting equilibrium. This is particularly true of the relation between contact angle measurements made under static conditions, and the wettability existing under the dynamic conditions of floods carried out at relatively high rates. We feel that this is a very important consideration, particularly in the floods the authors performed under what they consider to be "water-wet" conditions. It is our opinion that wetting equilibrium did not exist in these floods, except possibly at the very lowest rates. This opinion is in part based on some flooding tests we have made which are very similar to some of those described by the authors. These floods were made in unconsolidated cores, 6 in. long and 13/4 in. in diameter, made up of carefully graded glass spheres of the approximate size of the sand grains used in the subject paper. The cores were mounted vertically, and distilled water was used to displace a refined oil equivalent to the authors Soltrol C. The glass spheres had previously been carefully cleaned so that they were strongly wet by the water. The floods were made with and without an interstitial water saturation. When interstitial water was present, the solid surfaces were mostly covered with water prior to injecting the flooding phase. Consequently, a condition very near wetting equilibrium existed throughout the flood. The data in Fig. A show that under these eircumstances, rate had no influence on residual oil at flood-out, over the range of rates studied. On the other hand, in the absence of interstitial water, the surfaces are all covered with oil before the displacement. To achieve wetting equilibrium the injected water must displace the oil from the surfaces themselves. This is not a fast process. Therefore, the effective dynamic wetting condition in floods of this type must depend upon the flooding rate. When the flood rate is very low, compared to the rate at which wetting equilibrium is attained, the residual oil saturation at flood-out is essentially the same as the residual obtained when interstitial water is present. This is shown in Fig. A, and occurs because the dynamic wetting conditions are the same in both cases. However, at moderately high flooding rates, the rate has an important bearing on the amount of oil recovered because in this case the attainment of surface equilibrium is the slow step. We believe that, in the absence of an interstitial water saturation, oil recovery varies with rate because of the reasonably slow approach to wetting equilibrium which occurs during the displacement. In fact, as the rate is increased, the oil recovery performance indicates the core is becoming progressively less water-wet. At the highest rate there is even considerable simultaneous production of oil and water after breakthrough. This does not occur at the lower flooding rates, nor is there appreciable simultaneous oil and water produc-

Jan 1, 1957

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,' Barrett,' Dunn,3 and Richards' give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum' or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,'" aluminum,' or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.' Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", '" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By Allen Rogers

THERE are few natural monopolies comparable with the nitrate industry. Perhaps the only other one is, curiously enough, also an essential fertilizer material, viz., potash, of which the Germans have heretofore held practically a-monopoly due to the existence in their territory of the most important known deposits of potash salts. And although nitrates in minute amounts are found in many desert regions, the only deposits callable of being worked commercially exist in Chile. Combined nitrogen in the oxidized form is an essential for plant life. Nature provides it mainly through the agency of nitrogen-fixing bacteria. But where lands are cropped artificially this supply is too small; and gradually the nitrogen supply becomes exhausted. In order to continue farming, it is necessary to furnish a supply of nitrogenous plant food, and this is clone by putting on various substances containing combined nitrogen. These consist of various animal wastes, ammonium sulphate, the ammonia of which is obtained in the destructive distillation of coal, and Chile saltpeter. The latter is immediately available as a plant food, the nitrogen being in the required form. The other substances must oxidize before they are available. Besides its use as a fertilizer, Chile saltpeter is the source from which the bulk of the nitric acid of commerce is derived. The use of nitric acid in the manufacture of almost, all modern explosives is, of course, well known.

Jan 2, 1918

By Margaret V. Doyle, R. W. Powers

INTERNAL friction measurements, carried out as functions of temperature, have been used extensively to obtain data on the mobility of interstitial impurities in the Group V metals, vanadium, colum-bium, and tantalum. For a given frequency of vibration, the internal friction peaks at a temperature which depends principally on the particular metal and interstitial impurity. Relaxation times and corresponding activation energies are determined from a knowledge of such peak temperatures for various vibration frequencies. These experimentally determined relaxation times are related to the average jump frequencies of the interstitial impurity atoms using the model of Snoek1 and can be related to macroscopic diffusion coefficients as shown by Polder.2 In these Group V elements, the impurity whose diffusion rate has been the hardest to pin down by the internal friction technique has been carbon. The experimental difficulties associated with carbon in these metals were not evident in the earliest investigation carried out by Ke on tantalum.3 The carbon peak was thought to occur near 140°C at 1 cps on the basis of the enhancement of the height of this peak measured on specimens which had been coated with colloidal carbon and heated in vacuo at 1200°C. Presumably on the basis of similar evidence, Wert identified a peak also near 140°C at 1 cps in columbium with the diffusion of carbon in that element." Later, the difficulties of admitting carbon into these metals without simultaneously introducing oxygen were pointed out by Ang and Wert- nd by Marx, Baker, and Sivertsen.6 The latter suggested that the peaks attributed to carbon in tantalum and columbium might arise from the presence of traces of oxygen, adventitiously absorbed during the carburization. Such suspicion was confirmed, at least in tantalum, when it was found possible to prepare C-Ta specimens without contamination by oxygen. Specimens sci prepared, aitnough high in carbon content, gave no evidence of a damping peak near 140°C.7 Recently, the authors were able to Show that carbon diffuses in tantalum at a rate only slightly slower than that for nitrogen.8 At 1 cps, the carbon peak lies at 34g °C, only a few degrees above the nitrogen peak at 341 °C. However, the two could be distinguished by a different stability with respect to aging at 400 °C and by a different dependence of peak height on solute concentration. On the basis of this experience with tantalum, it appeared worthwhile to search also for a carbon peak in columbium in the vicinity of the nitrogen peak." In this report, the location of the carbon peak in columbium is made known and its position relative to the nitrogen peak is compared with the authors' previous findings in tantalum. In addition, a second source of internal friction seen only in specimens of very high purity is discussed. Columbium was obtained from the Fansteel Metallurgical Corp. as either 30 or 40 mil diam stock. The manufacturer gives the following analysis as typical of this material: 99.4 pct minimum Cb, 0.10 pct maximum C, 0.5 pct Ta, 0.04 pct Ti, 0.02 pct maximum Si, and 0.01 pct maximum Fe. Wires 13 in. long were degassed near 2200°C for 4 to 16 hr in an ultimate vacuum better than 2.10" mm Hg in an apparatus described previously.8 This treatment reduced the oxygen and nitrogen damping peaks observed in the as-received material to less than 0.0001 in Q-1 above background. The latter value varied somewhat from specimen to specimen in the range 0.0004 to 0.0008, depending chiefly on the wire diameter and the frequency of vibration. The high temperature evacuation left the specimen in a rather soft condition, the Vhn being reduced to 40 from a value near 121 in the as-received conGi~iur~. The gram size was about the diameter of the specimen. After outgassing, specimens were loaded with carbon by absorption of such hydracarbons as methane or ethylene. Carbon was also added to a few speclrnens by heating them at

Jan 1, 1958

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite