Search Documents

INTRODUCTION The meaning of cash flow has already been defined as after-tax earnings available for use by the corporation or business. It is therefore apparent that a significant part of mineral economic evaluation is concerned with correct and accurate computation of taxable income under existing tax laws, and the proper treatment of tax allowances and deductions. The various methods of depreciation, depletion, and amortization are all means whereby the investor can earn back or recover, before taxes are imposed, the investments made for purposes of doing business or for the production of income. Each of these three types of tax deduction are applied to different investment items such as property, equipment, buildings, research, etc. The cost of buildings, equipment, machinery, and transportation equipment are representative of capitalized business costs that must be recovered by depreciation over the life of the asset. The property investment costs of acquiring natural resources such as minerals, oil and gas, and standing timber are examples of investment costs that may be recovered by depletion. Several other capitalized business costs, such as research expenses and trademark expenses, may be recovered by amortization. The term "capitalized" means that the in- vestment cost is not deducted as an operating expense in the year that it is incurred, but is spread out over a period of years through depreciation, depletion, or amortization deductions according to lawful schedules. Of course, any capitalized cost can only be deducted once. The other costs of doing business which are not capitalized, such as labor and operating costs, are said to be "expensed," i.e., they are written off for tax purposes in the year they occur. DEPRECIATION Depreciation, according to US tax law, is a deduction from taxable income permitted as a "reasonable allowance for the exhaustion, wear and tear of property out of its use or employment in a business." The original cost of the property is the usual basis for determining depreciation. Since depreciation write-off is applied over the useful life of the asset, the first step is to determine the estimated useful life or its allowable depreciable life. These two lives may or may not be the same. No average life is applicable to all types of depreciable assets under different conditions or in different types of business. It is the taxpayer's responsibility to determine the useful life of the asset according to his own operating conditions and experience, within the guidelines set by the US Internal Revenue Service (IRS). The Class Life Depreciation Range (ADR) System permits the taxpayer to choose from a range of depreciable lives at 20% below or above the present guideline life. The second step required in calculating depreciation is to determine an estimated salvage value for the asset. The salvage value is an estimate, made at the time of acquisition, of the amount of money which can be realized by the sale of the asset at the end of its useful life. The four depreciation methods most widely used in the US are: (1) the straight-line method, (2) the declining balance method (double declining balance), (3) sum of the years - digits method, and (4) units of production method. Straight-Line Depreciation Method The straight-line depreciation method is the simplest for calculating depreciation. The depreciation for each year is determined by subtracting the estimated salvage value from the first cost of the asset and dividing the result by the years of life. The method gives equal annual deduction over the depreciable life. Salvage value equal to or less than 10% of the first cost may be ignored. [first cost - salvage Straight line = years of life ] Declining Balance Depreciation Method Declining balance depreciation, or double declining balance (DDB) as most frequently applied, is used for accelerating depreciation in the early years of the asset and is the fastest depreciation method allowed by the US Internal Revenue Service. The declining balance

Jan 1, 1980

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the Ger- man techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low- cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first German assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission- to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high- cost coke and anthracite for the production of water gas. Although varying degrees of success have been achieved and the water gas produced generally has been higher in calorific value, in only a few isolated in- stances has there been any sustained use of bituminous coal for water-gas production for public utility uses after the shortages of anthracite and coke have been lessened.

Jan 1, 1946

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By Arnulf Muan, R. W. Taylor

Activities of iron in Fe-Pt alloys have been dctermined by equilibrating mixtures of platinum metal and iron oxide at known oxygen Pressures in a thermobalance at 1300°C. Conzpositions and iron activities of the oxide phase at equilibrium are known from previous work, and compositions of the Fe-Pt alloy phase formed at equilibrium were detcvt?zined from the observed weight changes of the samples. The activity curve obtained shows a strow negative deviation from Raoult's law. THE present investigation was undertaken as part of a research program dealing with phase equilibrium relations existing among the oxides of iron and titanium at 1300°C. At low oxygen pressures of the gas phase in equilibrium with these oxides, the iron activity of the system is high, and considerable alloying of iron with the platinum used as a container material takes place. Thermodynamic data for Fe-Pt alloys at 1300°C are needed in order to evaluate quantitatively the extent of such reactions. Larson and chipmanlhave determined activities of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with CaO-iron oxide-SiOzmelts in which the iron activities were known. Compositions of the resulting Fe-Pt alloys were determined by chemical analysis. Mundiath and Gerassimov2 have studied thermodynamic properties of Fe-Pt alloys by electromotive force measurements in the temperature range 550" to 1000°C. The experimental method used in the present investigation is a slight modification of that used by Grube and Ratsch3 in studies of NiCr-alloys. 1) EXPERIMENTAL METHOD 1) General. Mixtures of platinum metal and iron oxide were equilibrated at 1300°C in atmospheres of known oxygzn przssures, and the course of the reactions was followed by measuring the weight changes of the mixtures. The principles involved in the derivation of composition-activity relations from these measurements are illustrated by the composition triangle for the system Fe-FeZO3-Pt shown in Fig. 1. Take as an example a mixture of FeZO3 (hematite) and platinum such that the total composition is represented by point T. If this mixture is heated to 1300c in air (poz = 0.21 atm) and the oxygen pressure is then reduced gradually, the oxygen content of the oxide phase decreases and increasing amounts of iron enter the metal phase. As the oxide phase and the metal phase for all practical purposes are insoluble in each other, their compositions are represented by points moving toward Fe along the joins Fe-Fe,03 and Fe-Pt, respectively. The total composition of the mixture during this process also changes, but only with respect to oxygen content, because the vapor pressures of iron and platinum are negligible at 1300°C. Hence the change in total composition is described by a straight line (constant Fe/Pt ratio) radiating from the 0 apex of the composition triangle Fe-Pt-0, of which the triangle in Fig. 1 is a part. Only one such line ("oxygen reaction line", T-T",) is shown in Fig. 1. The total composition of the alloy-iron oxide mixture at any instant must, in addition, be located on the straight line (conjugation line) connecting the two points representing the compositions of the two coexisting phases. It therefore follows that the total composition of the mixture at any instant is represented by the point of intersection between the conjugation line and the oxygen reaction line. An example of the situation prevailing at a chosen oxygen pressure, po2, is shown in Fig. 1 by points a' (alloy composition), b' (oxide composition) and T' (total composition). Point b' is known from the work of Darken and Gurry,4 and point T' is experimentally determined by the observed weight change of the mixture (distance T-T). Hence, point a', the composition of the alloy, is determined from the above data as the intersection between the join Pt-Fe and the extension of the straight line bl-7'. The activity of iron in the alloy at equilibrium is identical to that of the iron oxide phase, if the same

Jan 1, 1962

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber' in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman' has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By Thomas S. West

A gravel pack completion is described which, in addition to sand screening, permits the exclusion of water and gas from the oil production. A gravel pack composed of alternate layers of different particle sizes is employed which has horizontal but not overall vertical permeability to drilling mud. A packer is run on the tubing and set in the screen member, around which the gravel layers are placed. The hydrostatic pressure of a mud column prevents the entry of fluid above (or below) the level of the packer. The producing level may be changed by raising or lowering the tubing. Vertical coning is controlled by replacing the mud column with oil and continually injecting oil into the sand section above (or below) the packer. Three well histories with this completion are described in detail. Statistics on the first 100 completions of this general type are given. INTRODUCTION Gravel pack type completions have heretofore been almost exclusively for the purpose of preventing sand production. This paper describes and presents well data on a gravel pack procedure which is primarily a selective completion method. Although complete sand screening is achieved, the exclusion of gas and water is the primary objective. The application of this procedure is therefore not limited to unconsolidated sands. Application to hard sand or limestone reservoirs is equally feasible. GRAVEL PACK PROCEDURE Figs. 1 and 2 illustrate the gravel pack procedure employed. The gravel is placed by means of the frangible disc type dump bailer shown by Fig. 1.' This bailer has its lower end closed by a plate glass or steel rimmed cement disc. This disc breaks when the bailer passes over the liner allowing the gravel to be deposited around the liner. The liner employed is usually 2 3/8 in. to 2 7/8 in. OD and 1.995 in. or 2.07 in. ID (ID of 2-in. tubing or 2-in. line pipe). Two tvDes,. of slotted sections have been employed. One type employs horizontal hacksaw cut or milled slots of about 1/32 in. width opposite the producing section. The other type employs the same type,. of horizontal slot. but slots are placed in groups of six at intervals of about 8 in. A cage composed of half round vertical bars, spaced apart, is then welded to the pipe over the slotted sections. This liner has the bottom end closed, usually by bull plugging. The upper end is closed, while placing the gravel, by a cap which is held in place by means of a shear pin. This cap has a mandrel attached to it which extends downward inside of the liner to within a few inches of its lower end. The top of the liner cap is formed to fit a releasing type wire line core barrel overshot. The liner is lowered to bottom on the wire line by means of this overshot and released. The length of the liner is usually suffi- cient to extend to about 20 ft above the highest level to which gravel is to be placed, the upper end of the liner always being in the casing. The dimensions of the liner and bailer are such with respect to the casing size that the bailer will always pass over the liner. After releasing the liner the bailer is run to bottom. Passage of the empty

Jan 1, 1951

By A. Romero-Juarez

This paper is concerned with the effect of propping-agent concentration on flow capacity of a fracture in the case in which there is embedment of the propping agent. Previous published studies have shown definitely that there is a relationship between fracture flow capacity and prop ping-agent concentration, and it has been shown that the theoretical results are confirmed by laboratory experiments. The problem of directly finding sand concentration for maximum flow capacity of a sand-propped fracture is solved, and formulas and charts are given to obtain this concentration under various conditions of effective overburden pressure, medium sand-grain diameter and rock properties. It is shown that, for the same effective overburden pressure and the same rock characteristics, optimum sand concentration in pounds per gallon does not depend on medium sand diameter. For conditions met in bydraulic fracturing operations, it is found that sand concentration in grains per square inch for maximum flow capacity varies within a wide range of values; this indicates the convenience of using data of fracturing pressure and rock characteristics for calculating sand concentration in order to achieve the best results in fracture treatments. INTRODUCTION It has been pointed out in the published literature1 that one important factor controls the success of a hydraulic fracturing operation — the propping of the fracture. The main effect of the propping agent is to hold the fracture open by means of the reaction forces that oppose the pressure due to the overburden. It is assumed in this paper that the propping agent is sand, that the grains are spherical and uniform in size, and that this sand is distributed in a monolayer in the fracture. The existence of a sand concentration value for maximum fracture flow capacity has been recognized since the publication of one of the first studies on the subject.2 In the reference cited, flow capacity was assumed to be proportional to the cube of the fracture volume per square inch not filled by sand. The obtained experimental curves relating to flow capacity and sand concentration had the same appearance as the curves obtained with the afore-mentioned assumption. Recent work3 has shown that fracture permeability, in the case of a monolayer, can be calculated accurately by means of a modified Kozeny-Cacman equation; thus, it can be shown that fracture pqmeability is a function of free volume in the fracture and of the rock and sand wet surfaces. The flow capacity of a fracture is dependent on the permeability of the fracture and on the fracture width. If all excessive quantity of sand is present in the fracture, its width may be large but its permeability i:; low due to the greater flow resistance; too few grains of sand per square inch are present in the fracture, sand embedment in the rock is greater and the width becomes small enough to appreciably decrease the rate of flow. To determine optimum conditions of flow, therefore, it is necessary to know the dependence of fracture width on density or concentration of propping agent. This relation is given in a study4 in which the approach to embedment is similar to the one made in a penetration hardness test of metal. With the equacions presented by Darin and Huitt,3 the number of sand grains per square inch that results in maxirnum fracture capacity can be determined graphically by plotting fracture capacity vs sand concentration. Since the relationship between fracture capacity and sand concentration may be considered known, one is led to formulate the analytical problem of directly determining sand concentration for maximum fracture flow capacity, in order to study the effect of the various quantities that come into the process. The solution of this problem appears to be interesting both from the viewpoint of fluid mechanics and from the practical viewpoint of oil production in hydraulic fracturing treatments. EQUATION FOR FRACTURE FLOW CAPACITY It can be shown3 that the fracture flow capacity of a monolayer is given by the following expression,

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

By Walter Hull Aldridge

Much has been said about the foreseeable exhaustion of known mineral reserves-particularly in the United States. It is claimed that we are about to become a have-not nation insofar as certain essential minerals are concerned; and in this respect our position is often contrasted with that of the world as a whole, largely because we have drawn so heavily on our domestic resources during the last fifty years. As a matter of fact, the difference is not great if one takes a reasonably long-term view of the situation. No one denies that nature endowed the United States richer in mineral resources than any other equal area. It is granted that we have skimmed the cream of many kinds of minerals; but in a free international trade in minerals it would not be many decades before the richer deposits-at least the deposits easy of discovery throughout the world would be depleted to much the same degree as those in the United States today. For it is a fact that the problem of satisfying the needs of our industrial society for minerals is fundamentally worldwide in scope. The singular and significant attribute to all minerals is that there is but a single crop. Forests can be grown, but mineral deposits can be replaced only by finding new ones. Thus, one of the vital tasks of the mining engineer, the petroleum engineer, and the geologist is to find these new mineral resources. Another task is to devise means and methods for the exploitation of, at costs that are economic, low-grade deposits and those deeply buried in the crust of the earth. The first need, however, is to find the deposits in the ground. If the assumptions of those who today fear an early exhaustion of all deposits are valid, the outlook for continued material and social progress is gloomy indeed. I take a more optimistic view, for it is my belief that vast new sources of needed minerals will have come to light before our known resources are gone. The real question is whether the outside layer of the crust of the earth that is accessible to engineers contains adequate mineral deposits; and whether engineers can find those deposits. The answer must be based on geologic science, geologic fact, and mining history. Every continent, and almost every country, has yielded minerals of industrial utility in substantial quantity. Mineral deposits are widespread. Geologists know the conditions that were favorable to the occurrence of ores and the types of rocks in which various kinds of ores may ordinarily be found. They know that such rocks occur over broad regions of the earth's surface. They also know that in large areas rocks that are potential carriers of ores are covered and concealed by material of entirely different character. Such cover may consist of lava flows, layers of volcanic ash, or beds of material washed down from the surrounding mountains. Sometimes those covers are thick, sometimes relatively thin. But men well-qualified to pass judgment are sure that concealed deposits, large in number and in size, exist close enough to the surface to make exploitation practical. Only by actual penetration of the surface can this contention be proved, but to conclude otherwise would be to ignore the laws of probability and to deny the over-all consistency of nature. The task of probing the crust of the earth to determine the location of these deposits, and to obtain some notion of their size and quality, poses serious problems. However, they should not be beyond human solution. Much more research must be done in analyzing and explaining the laws of ore deposition. New tools, in the shape of techniques and methods and of mechanical and electrical devices and instruments, must be developed. But no reasonable person can doubt that these objectives will be achieved. As the need becomes increasingly pressing, scientists and engineers will supply the imagination and the ingenuity that will provide the solution. The time and effort thus far devoted to the development of methods for locating hidden ore bodies have been pitifully meager. Energetic investigation of the subject of applied geophysics is essential to the success of the mineral industry, and I have no hesitation in predicting that effective techniques will be found and successfully applied. Twenty-five years ago the petroleum industry

Jan 3, 1950

By R. S. Wagner, H. Brown

Criteria for nucleation with the aid of twin planes during crystal growth from the melt are discussed. It is shown experimentally that bismuth crystals can grow from a subercooled melt in a twinned bismdtic form. A mechanism of growth based on the presence of at least me twin plane is proposed. It is well known that faceted growth can be observed in crystals grown from the vapor phase, dilute solutions, or from the melt. Faceted growth, in which the crystal is bounded by its slowest growing faces, will occur if the growth rate is strongly orientation dependent. The addition of atom layers on a facet plane can only occur by two-dimensional surface nucleation or with the aid of an imperfection. Nucleation with the aid of dislocations was proposed by rank' and observed to be of particular importance in crystal growth from the vapor phase. Nucleation with the aid of two-dimensional imperfections, notably twin planes, was suggested by stranski2,3 and Frank.4 A twin plane, terminating at the growth interface, can form a reentrant step at which nucleation can occur at a much smaller super-saturation (or supercooling) than required for two-dimensional surface nucleation. Nucleation by a twin plane usually results in a fast growth rate along a crystallographic direction parallel to the twin plane. Such a nucleation mechanism, based on the presence of a twin plane, has been used by Dawson5 to explain the growth and morphology of sheet-like crystals of paraffin n-hectane. In recent years more evidence was found that nucleation by twin planes occurs frequently in crystal growth from the vapor phase and from dilute solutions, for example, in cadmium,' barium titanate,7 silver,8 silicon9 and gallium arsenide.10 In crystal growth from a supercooled melt, however, nucleation by twin planes has so far only been observed in materials with the diamond or zinc blende structure. Bennett and Longini11 were the first to recognize the important role a single twin plane plays in the growth of germanium dendrites. Subsequently, it was found that a prerequisite for continued propagation of germanium dendrites is the presence of two parallel twin planes which form a self-perpetuating system of nucleation sites.12 Sili- con and some III-V compounds such as InSb also grow dendritically by twin plane nucleation. It appears that the following criteria must be satisfied in order that nucleation with the aid of twin planes can occur: A) The growth form of the material must be faceted." B) The formation of twin boundaries, by a fault in layer sequence during growth, by plastic deformation, or by an accidental meeting of properly oriented crystals, must be possible. C) Twinning must form a reentrant step where the twin boundary terminates at the faceted growth interface. D) These three conditions are necessary, but in certain cases not sufficient for continued crystal growth with the aid of a twin plane. Depending on interface morphology, a combination of more twin planes is sometimes required to form a self-perpetuating system of nucleation sites. This investigation was carried out with the idea in mind that nucleation with the aid of twin planes is a more general phenomenon and should occur in those materials, grown from a supercooled melt, which satisfy the criteria outlined above. It has been found that crystals of high-purity bismuth grown from a supercooled melt can grow by the aid of a twin plane. In the first two sections the faceted growth form and the twinning elements of bismuth are discussed. In the last section prismatic crystals of bismuth, which appear to grow with the aid of a deformation twin are discussed.

Jan 1, 1962

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

By H. E. Wilborg, G. V. Henderson

This chapter deals with those sands employed by foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal is poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened by either heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%), and occurring in numerous locations thoughout the United States. Consumption End Uses Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe washed, graded, dried, and cooled clay-free sands which are found in many parts of the United States. They generally contain 90 to 100% silica but vary greatly in chemical analysis and grain structure. Lake sand is the sand dredged from Lake Michigan or dug from the dunes bordering that lake. Bank sand is composed primarily of silica grain but containing up to 5% clay. It is shipped in both the damp and dry state but the normal processing of bank sand consists only of drying and scalping. Occasionally two different grades of bank sand are blended prior to or during loading. Natural molding sand is a term used to describe a sand containing sufficient clay as mined to be suitable for molding purposes. Clay content may vary from 10 to 24% with the balance of the material consisting primarily of silica sand. These sands range in fineness from one peaked on the 20 mesh to one which contains more than 50% of the particles passing the 270 mesh. Lake sands are relatively coarse and are used in great quantities for the production of automotive castings. Bank sands and natural molding sands are gradually phasing out as the production of castings becomes more a science and less an art. The vast majority of foundry sands used today are those known as the silica sands and lake sands. Foundry sands are used in two basic ways. The majority are used in the green or uncured state with the balance used in the cured or set state. Green sand is grain bonded with clay and contains varying amounts of water to plasticize the clay in order to bond the grains together. Green sand is either naturally bonded or "synthetic" sand. The naturally bonded molding sands are generally found in the Hudson River Valley of New York State, Cumberland County in New Jersey, and in Tennessee and Mississippi. Synthetic sand is molding sand compounded in the individual foundry. It is made up primarily of graded silica sand, western or southern bentonite, water, and carbonaceous and/or cellulosic materials. Green sand is used primarily in making molds. The use of naturally bonded green sand has been declining for many years, primarily because naturally bonded sands are more difficult for the foundryman to find and control. Synthetic green sand, on the other hand, can be

Jan 1, 1983

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By D. R. Bomberger, M. Deul

An automatic microscope has been developed to measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed. In the study of coal cleaning by pseudo-gravity methods (tables, cyclones, hydrotators, etc.), it is customary to express the deficiency of the process relative to float-sink measurements in some form of "percent efficiency". These have been calculated in many different ways in order to provide a means of extrapolation of test data to untested coal feeds. This works quite well with coarse coal (here defined as larger than one-eighth in.). Large, heavy pieces of refuse are rejected rather thoroughly by many cleaning processes, and the efficiencies relative to float-sink results approach 100%. In coarse coals, the difference in the sizes of fine pyrite is masked by the averaging effect of the large coal envelopes. The existence and fate of fine pyrite is often hidden in the larger numbers representing coarse (and easily removed) pyrite. There are cases where it is desirable to subject fine coal (here defined as smaller than one-eighth in.) to cleaning processes. This is true of naturally occurring fie coal streams and in cases where comminution followed by cleaning is necessary to provide the quality desired. It is in this area that the use of process efficiency relative to float sink fails. Percent efficiencies decline to very low figures, and equivalent separation densities become a matter for conjecture. The net result is that an attempt to estimate product quality from float-sink data and a process efficiency figure often results in large errors. This work represents a new approach to the problem by observing the fate of pyrite particles, grouped by sizes, in a cleaning process. Examples are given which relate pyrite size measurements to float-sink washability and to a Deister Table operation. EXPERIMENTAL WORK The automatic microscope used here has been previously described.' Briefly, it is an instrument which measures the diam of particles (as defined by a range of reflectance) exposed on a polished specimen. The instrument scans a sample briquet, measures diam of exposed pyrite inclusions and records the data by size intervals. Preparation of the briquet is critical, due to the automatic nature of the process. The principal requirement is for an optically flat surface, so that focus will be maintained as the motorized stage moves the specimen under the lens. The various substances present must be polished to the same level in spite of the wide difference in hardness between coal substance and minerals. The polishing method must not pluck out small grains, which might be rather loosely held by surrounding coal. The procedure below was successful in producing all of these results. The coal sample (8 mesh or finer) was riffled (a micro vibrating riffle is essential) to obtain 15 g. One volume of Lucite powder (thermosetting plastic mounting medium) was mixed with three volumes of coal and mixed thoroughly. A briquet was formed using a cylindrical die (1 1/4 in. diam) at 3000 lb per in.* pressure and 150°C. Preparation of the optical surface was accomplished on automatic polishing equipment, according to the following schedule: 1) Grinding: 3 stages, using successively fine Carborundum grits of 180, 320 and 600 mesh. 2) Rough polishing: 2 stages, using 3µ alumina on cast iron, followed by 1µ alumina on lead. 3) Fine polishing: 2 stages, using 0.5µ alumina on napless broadcloth over bronze, followed by 0.1µ alumina on silk filament cloth over bronze. Raw data were corrected for the fact that the chords

Jan 1, 1964

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By M. Cross

INTRODUCTION The development of refining processes involving gas injection into liquid metals has seen the evolution of a variety of designs [I]. During the last few years or so the top, bottom and side blown processes have, essentially, been combined to produce a series of mixed gas blowing schemes (eg. the LBE [2,3] and LD-OB processes [4,5]). Although, a variety of mixed gas blowing processes have been carefully engineered and recorded operational experience now attests to their effectiveness, optimising their design and operational performance is another matter. Detailed process analysis of such operations is impeded by the complex nature of the physical and chemical processes involved: . fluid flow behaviour of the liquid metal and injected gases, . chemical reactions in the vessel, . mass and heat transfer within the fluid phases in the vessel, . influence of the geometry (eg. location of the tuyeres, etc.), . monitoring the operational performance. By and large, design and operating parameters evolve from a combination of laboratory scale experiments, pilot plant work and, of course, practical engineering experience. Conventionally, the gas-liquid system used to model the industrial process is air-water, for a number of valid reasons including – . visual demonstration plus geometric and (to some extent) dynamic similarity, . the fact that the system demonstrates, at least, qualitatively many of the complex features of gas injection - interaction between the gas and the liquid - the nature of the gas flow behaviour - qualitative indications of mass transfer rates Important experimental contributions to the understanding of gas liquid systems include the work of Brimacombe [6], Wraith [7], T.Robertson [8], D.Robertson [9], Guthrie [10] and Szekely [11] (these references provide starting points to identify the major published work in this area). Although air-water systems have been instrumental in providing a great deal of qualitative insight into the fluid flow behaviour of the processes, reliable quantitative predictions are more problematic. A number of workers (notably Brimacombe and colleagues [6, 12])have demonstrated that different gas-liquid systems can lead to wide variations in behaviour. Other limitations of physical modelling include the assumptions of isothermal flow, scale- up of turbulent flow behaviour and the inability to directly include the effects of chemical reactions. The above limitations in physical modelling, therefore, yield a natural role for mathematical modelling provided that it can be made comprehensive enough whilst remaining cost-effective. The major physical processes involved in gas injection systems may be summarised as . behaviour of the gas envelope structure in moving through the liquid metal . the global movement of the liquid metal . momentum interaction between the liquid metal and the injected gas . heat transfer and mass exchange via the chemical react ions. The behaviour of gas envelopes forming at a tuyere and then moving through the liquid has been investigated thoroughly by a large number of workers. Such models are generally based upon simple physic- al concepts derived from visual observation. An early model by Davidson and Schuler (DS), based upon a force balance between the liquid inertia and a combination of the bouyancy and momentum forces on the envelope, has proved to be a useful tool in predicting bubble volumes at detachment [13]. The DS model has been successfully modified in a number of ways [14-17] to cope with heat transfer and reactive transfer rates, etc. Furthermore, the basic ideas summarised above have also been confirmed on industrial converters by both Guthrie [I8] and Brimacombe [19]. Models have also been developed to predict the behaviour of the "chemical" component of some gas-liquid systems. However, one thing is clear; all gas-liquid reactive systems are governed by the degree to which effective mixing occurs. As such, the processes are dominated by the behaviour of the heat and mass exchange of the two phase fluid flow system. It is the pattern of movement of the turbulent liquid metal plus its interaction with the injected gas which must be predicted reliably, if sufficiently comprehensive comp-

Jan 1, 1984

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many loyalities. As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermoelectric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1—the validity of the calibration of the pyrite geothermometer; and 2— the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating pyrite geothermometer temperatures and thermoelectric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermoelectric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1953

By H. R. Brannon, F. M. Perkins, Weldon O. Winsauer

Both the abnormal resistivity exhibited by shaly reservoir materials and their potential are due to adsorption of ions. Interrelationships between the two have been derived and verified by laboratory results. These relations which have resulted from this work may be used in a qualitative manner to estimate whether or not a particular shaly reservoir contains hydrocarbons, and also to estimate the porosity of shaly sands. INTRODUCTION In spite of the progress which has been made in the last decade toward a better understanding and utilization of the electric log, there remain a number of problems in the interpretation of the log. One of these which is often troublesome is that of divining the nature of the fluids in sandstones or carbonate rocks which contain appreciable amounts of shale. It was shown by Patnode and Wylliel in 1949 that shaly rocks exhibit an abnormally low resistivity when saturated with solutions of low ionic concentrations. This phenomenon has been demonstrated to be due to the adsorptive properties of shale or clay in the rock.' In estimating the fluid content of shaly sands or carbonates from the electric log, it is desirable and sometimes necessary to correct for the abnormally low resistivity. A similar correction is likewise often necessary if attempts are made to estimate the porosity of a stratum from resistivity measurements. The correction may be made from data obtained on core samples and from information on salinity of interstitial water. Cores, however, are not always available. Moreover, even if cores are at hand, their examination is time-consuming. It would be most desirable, therefore, to make corrections of this nature from the log itself. Since both the abnormal resistivity and the potential' are consequences of the adsorption of ions on shale, it should be possible to utilize the potential curve to give better interpretation of resistivity data obtained in logging shaly materials. The work described in following sections was directed toward this end. THEORY Relation of Resistivity of Shaly Reservoir Rock to Adsorpttve Properties In discussing the effect which the presence of shale or clay exerts on the resistivity of a reservoir rock, it is convenient to make use of the resistivity factor.4,5 This quantity has been defined as the ratio of the resistivity of the rock when it is completely saturated with an electrolyte to the resistivity of the electrolyte itself. When the rock, such as a clean sand or carbonate, is free of shale the resistivity factor is virtually independent of the ionic concentration of the electrolyte used to saturate the sample, so that F = R0/Rw = constant for a clean rock . . (1) where F is the resistivity factor, R0 is the resistivity of the rock saturated with electrolyte, and Rw is the resistivity of the electrolyte. When the rock contains argillaceous material, the resistivity factor as defined above is no longer independent of the concentration of the electrolyte used to saturate the rock, but decreases as the ionic concentration of the electrolyte decreases. In explanation of this behavior, it is instructive to consider a sample of shaly porous rock placed in contact with a large volume of a dilute electrolyte. The sample is considered to become saturated with the electrolyte, and to attain equilibrium with it. As a result of adsorption by the shale surfaces within the rock, there is a greater concentration of ions in the solution adjacent to the shale particles in the interstices of the sample than there is in the external solution with which the

Jan 1, 1955