Search Documents

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By Georges Caraghiaur

INTRODUCTION A small, independent mining enterprise (SIME) is an independently owned and operated business concern engaged primarily in mineral development, from the exploration to the production stage. By definition, a SIME is not dominant in its field and has no long-term financial backing. It is not a major producer of minerals, nor is it a petroleum company, a government organization or a subsidiary of such organizations. A SIME may or may not be listed on stock exchanges. The SIME is also called small miner, junior mining company, speculative mining company, and penny-stock mining company. The survival and growth of a SIME is most often controlled by an independently minded entrepreneur, who not only conceives and carries out new projects, but is materially affected by the success or failure of these projects. Usually, a SIME does not have a large or constant cash flow. Such a lack of long-term financial backing forces the SIME to meet the challenge of finding capital for its activities on a step-by-step basis. Its survival strategy is thus based on finding funds at the right time, of the right type and in the right quantities. The purpose of this paper is to show that the type of venture in which a SIME is involved affects the difficulty of raising new capital and the choice of possible sources of funds. The Small, Independent Mining Enterprise (SIME) The SIME is not a figment of the imagination of financial speculators. In Canada, there are more than 1,800 small mineral enterprises which spend on the average less than $1,000,000 per year on activity which is directed at bringing forth new mineral supply. In the United States, 64% of the non-fuel mining operations are conducted by nine or fewer men, and the coal industry is characterized by several thousand smaller independent producers, still predominantly family owned or controlled. In Chile, 80% of the mines can be classified as small mines. In the Philippines, approximately 60% of metal mining operations are classified as small mines. The SIME is actively engaged in mining all over the world, and very much so in the Pacific Rim. The Mineral Supply Process The whole process of bringing forth new mineral supply involves a dynamic sequence of activities, ranging from the initial exploration for a mineral occurrence to the production of a marketable product. A typical sequence is outlined in Figure 1. At the grass-roots exploration stage, a series of geological, geophysical and geochemical tests is aimed at locating a mineral occurrence. Especially in the early phases of such activities, the uncertainty (risk) surrounding a venture is high, since only general geological information exists on which to base a judgement of the economic viability of the venture. Such risk is attractive to few investors. As the information-gathering process continues, uncertainty diminishes. Once exploration efforts result in the discovery of a mineral occurrence, i.e. when indications of mineralization and mineable widths are obtained by drilling, there is still uncertainty concerning the extent of mineralization and the probability of having located an economic mineral deposit. The expected return on investment at such a stage may well be negative but the slight possibility of a very high positive return will make a number of financial sources available to an exploration company. At the development stage, much of the uncertainty

Jan 1, 1985

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.'" One of us (A. D. Le C.) has calculated from Johnson's results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson's reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.' aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By L. D. Lamont, W. C. Muehlhof

Throughout the anthracite industry's history, the problem of handling and disposing of refuse material has been one of major importance. In the early days of the industry's activities, only the large sizes of anthracite were satisfactory for market requirements and the smaller sizes were deposited as refuse. As time went by, more efficient coal-burning equipment was developed and a market demand was created for the finer sizes of coal. This demand made it possible to recover marketable coal from banks deposited as refuse in the earlier days of mining. The same condition holds good today and we can see a definite trend toward the objective of utilizing the No. 4 and No. 5 buckwheat sizes. Under present conditions, we know that a limited market exists for No. 4 and 5 buckwheat; we know that the finer sizes of anthracite can be burned as pulverized fuel; we know that these fine sizes can be processed and sold as briquettes, and we also know that the heat content of these fine sizes of coal is comparable with that of the sizes now merchandized. Therefore, it should be the objective of the industry to conserve these fine sizes of coal in such manner that if and when processing facilities are developed, and market demands exist, the material can be salvaged and made available to meet these demands. From the standpoint of economical future reclamation, the ideal method of disposing of refuse containing the finer sizes of coal is to deposit it in banks separate and apart from other breaker refuse. By this procedure, the minimum amount of material will be processed in future salvage operations to recover the No. 4 and No. 5 buckwheat sizes. Many collieries in the anthracite region are operated under leases that have a specific term. These lease agreements provide that, upon expiration of the lease by term, exhaustion or otherwise, the ownership of the refuse material reverts to the lessor. Therefore, a question was raised in the minds of these operators: Why should I assume the expense of such procedure when I have no assurance that I will benefit by the future processing and sale of these fine sizes? Under present conditions, the answer to this question is not one of choice but of necessity, as restrictions imposed by legislation make it mandatory on operators of preparation plants to take necessary steps to properly treat silt-laden waters before permitting them to enter the streams. By reason of these restrictions, the disposal of fine sizes becomes a secondary rather than a primary operating consideration, and the procedure for disposing of this refuse becomes a matter of choice governed principally by topographical and geographical conditions. Methods of Handling Refuse There are three principal methods of handling and disposing of fine-size refuse; namely:

Jan 1, 1947

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By O&apos, R. G. Meara, M. M. Fine

One of the principal activities of the Bureau of Mines connected with the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydrofluoric acid, such as the use of the anhydrous acid as a catalyst in production of high-octane gasoline and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorite. † In 1943 the consumption of acid-grade fluorite was advancing at a more rapid rate than production, and was only slightly less than production during the latter half of the year.' The outlook for the postwar market for fluorite is encouraging Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a postwar demand for fluorite equal to about 60 to 75 per cent of the wartime production.1,2 Others believe that the postwar fluorite industry will be permanently expanded over its prewar status3 Acknowledgment This paper is one of many reporting on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources. The program has been under the general supervision of R. S. Dean, Assistant Director, since July 1942. The scope of the paper falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficultly beneficiated ores, the production of pure metals from domestic deposits, the exploitation of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice. The investigation was initiated at the request of Mr. J. H. Steinmesch, vice-president and general manager, Minerva Oil Co., Eldorado, Ill. His hearty cooperation and helpful suggestions, and those of Mr. 0. E. Anderson, mill superintendent,

Jan 1, 1947

By W. B. Stephenson

In the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of 'successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. Basic Requirements To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,' who says, among his conclusions: "... values of f (friction factor) . . . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head' is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. Maintaining Constant Volume Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping systen]. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1947

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By N. A. D. Parlee, I. D. Shah

The solubilities of oxygen in liquid Ag-Au, Ag-Pt, and Ag-Pd alloys have been determined in the range of 940° to 1200°C at 1 atm pressure of oxygen using an improved Sieverts technique. The additions of gold (0 to 57 pct), platinum (0 to 27 pct), and palladium (0 to 22 pct) to liquid silver continuously decrease the solubility of oxygen in liquid silver. Activity coefficients and interaction coefficients of oxygen in these alloys and have been calculated. The interaction coefficientscan be described by the following equations: Approximate second-order interaction coefficients (pM have been calculated. The contribution of the product, pMxNM, to In yo only becomes significant at high alloy concentrations. RECENTLY several investigators1"3 have redeter-mined the solubility of oxygen in liquid silver. In general the recent findings1" for Po, = 1 atm are in good agreement with the equation:4 log %O = 695.4/T + 1.086 [1] It is established1, 2 that the solubility of oxygen follows Sieverts' law reasonably well, at least up to 1 atm partial pressure of oxygen. It should be noted that a very slight deviation from Sieverts' law has been reported by Lupis and Elliott.3 Only recently has the solubility of oxygen in Ag-X binary liquid systems received much attention, and only the Ag-Cu, Ag-Au, Ag-Pt, and Ag-Pd systems have been studied. Par lee, Sacris, and zoellners reported that the solubility of oxygen in liquid silver increases progressively with the small additions of copper (0 to 0.5 pct) up to the point where the copper oxide phase appears. Lupis and ~lliott~ have reported that the solubilities of oxygen in liquid silver decrease progressively with the additions of gold, platinum, and palladium. However, their investigation was limited to 0 to 5 pct of these alloying elements, a range too limited to satisfy the requirements of the research program of this laboratory, where the solubilities of oxygen in the range of 0 to 30 pct were required for the calculation of chemical diffusion coefficients of oxygen in these alloys. The present paper deals only with the solubilities of oxygen in these alloys while another paper will deal with the diffusion of oxygen in these alloys. EXPERIMENTAL METHOD A Sieverts technique was employed which involved an improved design of the reaction tube, Fig. 1, as described briefly in a previous communication.4 Liquid melts (70 to 100 g) were held in Norton Alun-dum crucibles. The induction furnace used had a maximum output of 2.5 kw with very fine control. This induction system had excellent stability and the final equilibrium temperatures measured by calibrated Pt-Pt, 10 pct Rh thermocouples are believed to be within ±2C. These thermocouples were checked against the melting point of pure gold wire, and the results agreed with standard tables (±l°C). Each run involved a careful sequence of operations. The sample was heated to and held at about 900°C in vacuum for 3 to 4 hr with the thermocouple in a retracted position. After melting, the melts were usually exposed to a small amount of oxygen (0.5 to 2.0 cu cm) and then degassed slowly for 1 to 2 min to remove any oxidizable volatile impurities such as carbon and sulfur as CO, CO2, SO2, and SO forth. Argon gas was then allowed to enter the system. The protection tube containing the thermocouple was then

Jan 1, 1969

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry. At the coal washing plant of the Colorado Fuel and Iron Corp., washed coal from the Deister Plat-O tables is sluiced to a stationary inclined de-watering screen provided with 3/16 by 1-in. slots, and the coarse coal passing over this screen is conveyed by a Baum-type elevator and a flight-type distributing conveyor to a battery of Carpenter centrifugal driers. The fine coal and water passing through the openings of the primary dewatering screens, plus the fine coal passing through the screens of the centrifugal driers (and no small portion of which is the result of the disintegrating action of these driers) is pumped to two 30-ft Link Belt settling cones. The sludge recovered as underflow from these cones was formerly dewatered on stationary screens having 1/16 by 1-in. slots and discharged on top of the coarse washed coal in the Baum drainage conveyor; but after a relatively few hours of op eration the circulating load of fine coal on this conveyor built up to a point where it became necessary to reduce the quantity of feed to the washing tables. The original arrangement of our coal washing and dewatering equipment is shown in Fig 1. In order to regain the loss in active throughput which had been caused by this circulating load, an installation of six vibrating filters was made during the year of 1936. This resulted in an increase in normal tonnage of washed coal from 1430 to 1750 tons per 8-hr shift, a gain of slightly over 22 pct. This increase in throughput has made a very substantial decrease in the " conversion cost" per ton of washed coal. Since the vibrators were installed, we have gained about 2,000,000 tons in production, compared to what would have been produced in the same number of shifts at the former rate. Putting it in slightly different form, we have saved in the past 12 yr the cost of 1400 operating shifts in the washery. Fig 2 shows the location of the vibrating filters as applied to the original flowsheet. It will be noted that the sludge from the bottom of the settling cones is passed through a distributing box and thence to the filters. The de-watered coal from the filters is de-livered to the conveyor receiving the dried coal from the Carpenter driers.

Jan 1, 1950

By William P. Roe, James F. Ellis, W. P. Fishel

This paper reports the distribution of sulphur between iron and titanium in Fe-Ti-S alloys and in Fe-Ti-C-S alloys. The compound TiS was found, which exists as a separate phase at temperatures below 1200°C. Titanium in steels reacts with sulphur in preference to carbon. THE general relationship between sulphides and oxides suggests that titanium should form a sulphide having properties similar to those of titanium oxide. Specifically, titanium should form a sulphide having a high melting point, indicating a stable compound of low solubility in iron. In order for titanium to function as a desulphurizer or sulphur-fixing agent, it must form a stable sulphide. In order for titanium to be useful in steels as a sulphur-fixing agent, it must react with sulphur in preference to carbon; and to prevent red shortness, the sulphide formed must have solubility characteristics such that grain-boundary precipitation of a low melting phase be prevented. The terms desulphurizer and sulphur-fixing agent when used in this paper mean that titanium effectively ties up the sulphur as a stable sulphide of titanium and prevents the formation of FeS. The partition of sulphur between iron and titanium was studied first in a series of Fe-Ti-S alloys with carbon absent, and then in similar alloys with carbon present. It has been established1 a that titanium forms in Fe-Ti-S alloys a sulphide of undetermined composition which can be identified microscopically, and that the titanium-sulphur compound does not respond to sulphur printing. It has been suggested" that titanium acts as a sulphur-fixing agent, although little proof has been given. A report% f The Advisory Committee on Metals and Minerals summarizes the existing knowledge concerning substitutes for manganese in steels. Distribution of Sulphur Between lron and Titanium with Carbon Absent The alloys for this investigation were made by -melting Armco iron, metallic titanium, and iron sulphide in alundum crucibles in an induction furnace. The titanium was added after the other ingredients had melted. In these alloys it is recognized that some TiO, is present, since the melts were made in the air and since no other deoxidizing agent was used; therefore, some of the titanium was not available for union with sulphur. Thirteen ingots were made. Ingots 2 to 8 were cast in baked-sand molds; ingots 12 and 13 were cast in metal molds; and ingot 9 was allowed to cool in the crucible in which it was melted. All ingots were annealed at 900°C for 3 hr and were cooled slowly in the furnace. Subsequent information indicates that this anneal had no effect upon the titanium sulphide particle size, since the sulphide does not go into solution at this temperature. The ingots as-cast were approximately 8 in. long and % in. diam. The compositions of the eight ingots and the results of the partition of sulphur are recorded in Table I. Total titanium and total sulphur were determined by standard gravimetric methods. Sulphur, as iron sulphide, was determined by the evolution method. Boiling HC1 (1:4) liberates the sulphur from iron sulphide, but leaves the titanium sulphide practically undecomposed. A complete separation of titanium sulphide and iron sulphide cannot be made by digesting these compounds in dilute HC1 since titanium sulphide was found to dissolve slowly. The amount of titanium sulphide decomposed will depend upon the time in contact with the acid and upon the particle size of the sulphide. The point

Jan 1, 1952

By L. Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope' at the supports (Fig. 1). Essentially this assumes:5* ?A = ?, = ?b and dA = dB = 0. However, a host of conditions can cause differential sag or deflection at one support, and even an apparently trivial deviation can have major consequences in the beam: variations in spacing, size, and material of supports; local settlement due to floor heaving or lower mine openings; non-uniformity in wedging or bolt tensioning.8 In one particular instance concrete pillars, poured in place, shrank away from the roof upon setting.' When understood and controlled, differential sag becomes a definite advantage, permitting the transfer of loads from one support to another. Where one support is a bolt or prop and the other a pillar or rib, the load on the former can be reduced while the load on the pillar or rib is increased. This means two things: 1) savings can be effected by using smaller artificial supports such as props and bolts and 2) loads can be increased in the rib to induce eventual failure for longwall caving. In this last respect, another factor underlying coal bumps becomes understandable. The design of a mine roof by beam theory assumes that when a bedded formation is homogeneous, iso-tropic, and elastic, it will act like a uniformly loaded beam, fixed or clamped at both ends,6 s in Fig. 1.'" These are important assumptions. The uniform load is the weight of the beam itself or its body load. For a beam of unit width, this load becomes per foot: w = yhb. w = uniform load y = specific weight, lb per ft3 h = depth or thickness of beam, ft b = width of beam, ft Since b = 1, w - yh [ 1 ] A beam fixed at both supports is statically indeterminate to the second degree, that is, two equations in addition to those for static equilibrium are required to determine the reactions at the supports. These equations result from the geometry. From statistics: ^F,= 0;RA + RB — wL = 0 [2] wU S,M0 = 0 ; MB H------------MA — RBL = 0 [3] it Using superposition in which the left support is kept intact and the right one resolved into an active force and moment, we obtain from Fig. 2:" ?b = ?m + ? b2 + ?B3 = 0 dB = dB1 + dB2 + dB3 / wU Ma RBL \ V d°=(-r+-2—r)-zr [5] Where: Subscripts refer to position on axis of beam R = force, lb M = moment, ft-lb w = uniformly distributed load, lb per ft L = span, ft 0 = slope, radians d = deflection, ft E = Young's Modulus, lb per ft" 1 = Moment of inertia about the neutral axis, ft4 Solving Eqs. 2 through 5 for the four unknown reactions, we obtain: 2 L3 Fig. 3 is obtained by plotting MA and M, vs d, and then plotting RA and R, vs d, and adjusting their scales to coincide with MA and M, vs d,. It should be noted in Eqs. 6 and 7 that as dB increases, MA increases the same amount that Mn decreases. Eqs. 8 and 9 show a similar relationship between RA and R,. Proof that MA is the maximum absolute moment occurring in the beam is as follows: where M, = moment at x wx-When where M,., = maximum positive moment Eqs. 6 and 8 into above: For small dn: MA> M,,,

Jan 1, 1960

By John McGhee, Jack Newcombe, M. J. Rzasa

A series of water floods was made on laboratory prepared unconsoli-dated sand columns to study the effects on oil recovery of the solid-water-oil contact angle, the oil-water interfacial tension, flood rate, and oil viscosity. A procedure was developed for treating silica sand with silicone polymer to produce surfaces of varying degrees of wettability as evaluated by measuring the contact angle on a flat silica plate that had been simultaneously treated with the sand. Fluid interfacial tensions were changed by the use of surface active agents in the flood water. Water-wet, oil-wet, and intermediate wettability systems were studied at high and at low values of interfacial tension, at several flood rates, and with oils of different viscosities. For both oil-wet and water-wet systems and a low viscosity oil, recoveries were functions of the oil-water interfacial tension; also, increase in flood rate resulted in increased oil recoveries. High interfacial tension floods were more efi- cient than low interfacial tension floods on water-wet systems, while low interfacial tension floods were more eficient on oil-wet systems. Intermediate or neutral wettability systems were less sensitive to rate of flood advance and interfacial tension than either oil-wet or water-wet systems. The eflects of surface forces on oil recovery for high viscosity oils were not so well defined as for low viscosity oils. INTRODUCTION Reservoir rock surfaces vary in their wettability1, some being water-wet while others are apparently oil-wet. The factor of wettability enters into reservoir performance in both primary and secondary recovery, and into laboratory measurements of capillary pressure, connate water saturation, and relative permeabilities.' In theory, the degree of wettability is measured by the contact angle for the system solid-water-oil. A water-wet system is defined as one in which the advancing water contact angle is less than 90". An oil-wet system is one in which the advancing water contact angle is greater than 90°.3 The surface forces in a solid-water-oil system are related by the Young-Dupree equation as follows4: These surface forces are commonly expressed as the difference in adhesion tension, or the product of the water-oil interfacial tension and the contact angle. If the contact angle is less than 90°, the adhesion tension difference is positive and oil displacement by water from a solid surface will be spontaneous and favored by a high oil-water interfacial tension. If the angle is greater than 90" the displacement will not be spontaneous but will require less energy the lower the oil-water interfacial tension. The contact angle and interfacial tension also appear in the capillary pressure equation5: PC = 2ocosejr .... (2) The quantity cos was used by Rapoport and Leas6 s a factor in the generalized form of their "sealing coefficient." Warren and Cal-houn' presented the results of cos on oil recovery in oil-wet systems and correlated their data using a "scaling coefficient" suggested by Jones-Parra and Calhoun.8 The "sealing coefficients" were advanced to help correlate the effects of the variables influencing oil recovery by

Jan 1, 1956

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 BROADWAY, NEW YORK, N. Y. J. E. JOHNSON, JR. F. T. RUBIDGE, Treasurer, P. G. SPILSBURY A meeting of the New York Section was held at The Machinery Club on Friday evening, Oct. 4, 1918, The Chairman, Allen H. Rogers, presiding. The CHAIRMAN.-MOST of us, I suppose, have been affected more or less by The request of The Fuel Administration that we leave our automobiles standing in The garages on Sundays. We shall all be interested in hearing about The situation that has called forth This, request, and The Oil Administrator, Mr. Requa, has kindly come from Washington to Tell us about it. MARK L. REQUA.-I am very glad To Tell you about the oil problem during This war period. The United States is supplying by far The greater part of all The petroleum products consumed in Great Britain, France and Italy. In addition To This, we have had To supply a marked increase in our domestic consumption, not only of The refined products, but of fuel oil as well. The combination has put a strain on The oil industry, which it is very difficult To meet. The oil companies, being under contract, had no option as To who should get Their oil first, and They were delivering pro rata To everybody; manufacturers of furniture were getting oil with The same regularity as Those who were making aeroplanes or munitions, and The oil companies felt that something should be done. The first order with which I had. anything To do was The priority list for The delivery of fuel oil. That list contained 12 classifications, beginning with bunker fuel and railroads, and you will realize The complexity of The situation when you hear that munitions plants are in class 11. The priority list held during The winter, but transportation became so bad, because of The number of ships that were Taken for trans-Atlantic use, that some of The oil companies were not able To deliver more Than about 60 per cent. into class 5, and nothing beyond that point. To add To the Troubles, the Tank-car mileage fell off. The average for 1917 was about 36 miles per car per day. in January, 1918, it dropped To about 8 miles, and it must have been nearly zero in The early part. of February. Because of The extremely severe winter, furthermore, pipe lines were not delivering anywhere near Their normal capacity. A new priority list has recently been promulgated, introducing a few slight changes. Natural gas has been brought under its provisions, and it has been extended To include The Pacific Coast, which was not considered necessary last winter. The situation in The gas industry is not satisfactory; it is estimated that There will be a decrease of 10 To 20 per cent. in The quantity of natural gas available This winter, as compared with last winter.

Jan 11, 1918

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By Edward H. Robie

SHOULD the name of our Institute be changed? Perhaps one should say, should it again be changed, for until 1919 the name was the American Institute of Mining Engineers. When the American Institute of Metals joined our ranks we became the American Institute of Mining and Metallurgical Engineers. To make it a full mouthful, and strictly legal, one should add the word "Incorporated." At the June meeting of the Board of Directors it was suggested that this name was not a particularly happy one, especially so far as members of the Petroleum Branch, comprising a quarter of our membership, were concerned-not particularly appropriate as the name for the professional society for petroleum engineers. Apart from the petroleum group, the present name is felt by some not to be sufficiently comprehensive. Most geologists and many metallurgists, ceramists, and fuel technologists, for instance, are not engineers. They could never qualify as registered professional engineers under the licensing laws and yet they are valued and fully qualified Members of the AIME. The Directors, at the June meeting, thought the idea of a change in name should be presented to the membership for discussion, and suggested this column as the avenue of approach. Nine years ago Dean Steidle, of Penn State, recommended among other things that the name of the Institute be changed to "American Institute of Mineral Technologists and Engineers." In an editorial in Mining and Metallurgy in January 1944 objection was offered to this name but "American Institute of Mineral Engineers" was suggested. A special committee appointed by the Board to review Dean Steidle's suggestions (W. B. Heroy was Chairman) suggested that if the AIME were starting from scratch, the American Institute of Mineral Engineers might be a preferred name. It was not thought that the change suggested by Dean Steidle was one of major importance, and the comment was made that "the present name has gained prestige through many years and is cherished by our membership. An important element of 'good will' is attached to it and some of this would be unquestionably sacrificed by any change." In M&M for February 1945, Oliver C. Ralston went into the derivation of the terms mineralogy and metallurgy, and pointed out that both Mining and Metallurgical mean "digging," etymologically. He went on to show, with tongue in cheek, that if we want a short and all-inclusive name it should be American Institute of Geo-urgists, or, for euphony, Geolurgists. Oliver's brilliant development seems to have been received with speechless wonder! Should a decision ever be made to change the name, we think most members will agree that the American Institute of Mineral Engineers is to be preferred over anything yet suggested. "Mineral" has become, through usage, a much broader term than is indicated in the dictionary. Webster states that a mineral, in the true sense, must be inorganic, but Murray's Oxford English Dictionary seems more liberal, defining "mineral" as "any substance which is obtained by mining; a product of the bowels of the earth;" and "mineral oil" as any oil of mineral origin, as petroleum or shale oil. Certainly "the mineral industry" is ordinarily taken to include those activities based upon processing all the metallic and nonmetallic ores and deposits found in the ground, including the fuels. One advantage of this title is that the familiar abbreviation, "AIME" need not be changed. The advisability of maintaining a well-known abbreviation is evident, and was recognized, for instance, when the Committee for Industrial Organization became the Congress of Industrial Organizations some years ago. But if the petroleum engineers are the ones to be chiefly considered in revising the name of the Institute, it is by no means certain that they would feel that they are much more adequately recognized in a group of Mineral Engineers than in a society of Mining and Metallurgical Engineers. 'And then there remain, of course, the considerable number of professional members of the Institute who are not engineers at all. Comment from readers is invited.

Jan 1, 1952

By C. D. Ramsden

DURING the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Pur¬chase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by sal¬vaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a con¬siderable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been re¬building locomotive wheels for several years with automatic open arc-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under¬flux arc-welding process for wheel rebuild¬ing, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three- sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. OPEN ARC WELDING With the open arc process, a set of wheels could be rebuilt for about 40 pct of the cost of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or posi¬tioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1946

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963