Search Documents

By Herbert H. Kellogg

IN 1930, Taggart, Taylor and Knoll1found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the "classical "[t] theory of Brownian movement and proposed an "ionization" theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,"5 Wark's "Principles of Flotation,"6 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.7 Bankoff15 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, all particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid-the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that the addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1945

By M. A. Torcaso, P. Raimondi

The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil. A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sor The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston-like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. INTRODUCTION A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two-phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would be represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil. called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition. of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important.

Jan 1, 1965

By Carl Wagner

This paper contains solutions of the differential equation of diffusion in binary alloys if the diffusion coefficient is an exponential function of the concentration of one of the components. THE general differential equation for one-dimensional diffusion in a binary system can be written as: where c is the concentration of one of the two components in any suitable units; x, the distance from a reference plane; t, time; and D, the diffusion coefficient. Hartley and Crank&apos; have pointed out that eq 1 with conventional length units for measuring the distance x holds only if the alloy can be regarded as a rigid framework. In general, this is not the case, especially if the lattice parameter varies appreciably with composition. If a modified coordinate system is used instead of an orthodox system based on the centimeter a:: length unit, eq 52 is obtained, which has the same general form as eq 1 and is generally valid. The necessary transformations are presented in the appendix. If&apos; D is independent of concentration, analytical solutions of eq 1 are known for numerous boundary conditions. If D depends on concentration, solutions based on known analytical functions are not available. Among others, Boltzmann2 and Matano3 have shown that the concentration c depends only on (x/t1/2) in the case of diffusion between two semi- infinite spaces with uniform initial concentrations: c = c, for x < 0, t = 0, i.e., x/tl/2 = — x [21] c = c2 for x > 0, t = 0, i.e., x/tl/2 = + a Moreover, Boltzmann and Matano have shown how D may be calculated as a function of concentration over the whole range of composition from c -c, to c = c2 if c as a function of (x/t1/2) for the initial conditions stated in eq 2 has been determined experimentally. Thus, for instance, in principle, the diffusion coefficient in silver-gold alloys may be calculated as a function of concentration for the whole range of composition from only one diffusion experiment with a couple of pure silver and pure gold welded together. If the diffusion coefficient D as a function of concentration c is known, a solution of eq 1 for boundary conditions as stated in eq 2 with arbitrarily chosen values of c, and C2 may be wanted. For instance, if the diffusion coefficient in an alloy A-B as a function of concentration has been derived from an experiment with a diffusion couple involving 0 and 30 pct B as initial. concentrations, the calculation of the concentration distribution in a diffusion couple involving other initial concentrations, e.g., 5 and 20 pct B, may be desired. This problem may be solved by numerical or graphical integration of eq l. The solution of an ordinary differential equation of second order, which results from using (x/t1/2) as an independent variable, can be computed quite rapidly if two conditions for the same value of the independent variable are given. In eq 2, however, two conditions are given for two

Jan 1, 1953

By N. H. Darton

In the coastal plain region of the middle Atlantic slope there are no large supplies of potable surface-waters. The great rivers by which the region is intersected are tidal estuaries, and the water of their local branches is often of bad quality. The cities situated at intervals along the western margin of the region obtain a plentiful supply of excellent water from the rivers above the tidal estuaries, but out on the coastal plain surface-waters are mainly used. A few artesian wells have been sunk which afford abundant water, but their number is at present very limited. Norfolk, Newport News, and the many smaller places use surface-waters, and all over the region there is great need for purer and more abundant supplies. During the past five years I have been engaged in a study of the geology of the coastal plain for the U. S. Geological Survey, and have given special attention to the question of subterranean waters. In this communication I shall present a brief review of the geological conditions under which such waters occur in this region, and give an account of the wells which have been bored. Unfortunately the number of well-records is small, and some of the most important questions of subterranean geology are as yet far from settled. It is hoped that this paper may lead to further borings, especially as the cost of artesian wells has been much reduced by the introduction of new machinery and methods, and is now quite within the reach of the average community. In New Jersey there are many wells, and the water-bearing horizons are so definitely determined that they may almost everywhere be predicted with certainty. In Maryland and Virginia the data are less definite, but there is excellent evidence of a wide distribution of water at moderate depths.

Jan 1, 1895

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter&apos; listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7&apos;8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen&apos;s observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

By L. W. Saperstein, D. Yeung, L. B. Phelps

Introduction The success of preventive methods for the mitigation of coal mine drainage formation will require a marriage of the minimization of initial coal mine drainage formation, the minimization of toxic fluid formation after toxic material disposal, the minimization of the mobilization and transpor¬tation of formed toxic fluids, and the maximization of the rate of diultion and attenuation of the formed toxic fluids. This paper contributes to the understanding of factors af¬fecting mobilization and dilution and attenuation of formed toxic fluids. When water containing a salt content different from in situ pore water in the soil is passed through a body of soil, the concentration of salts in the outflow will gradually change composition in a manner that depends on the kinds of hydraulic processes that occur in the soil. These processes are molecular diffusion, lateral dispersion, longitudinal dispersion, chemical reactions or exchange, physical adsorp¬tion, and biological retardation. This note considers only the first three processes. These three microscopic processes can be analyzed statistically on a probability basis. Such results, confirmed experimentally, indicate that a tracer introduced instantaneously as a point source will tend to form a Gaussian normal distribution as it moves downstream (Todd, 1964). Dilution During Flow The closed-form soltuion for pulse or instantaneous injec¬tion of a tracer during confined flow in a homogeneous porous medium shows that the maximum tracer concen¬tration at a point in space, x, after the time interval, t*, is given by [ ] where Aa is the effective flow cross-sectional area; A is the column cross-sectional area; a is soil porosity; M is mass of the injected tracer; C is concentration of the tracer in the permeating fluid and is a function of x and t*; D is the longitudinal dispersion coefficient; and va is the interstitial fluid velocity (Klotz and Moser, 1974). Therefore, the following conclusion can be made: • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, and a fixed mass of injected tracer, M, Cmax will decrease as the time of peak outflow concen¬tration t* increases. • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, a fixed mass of injected tracer, M, and a constant interstitial fluid velocity, va Cmax will decrease as the distance of travel, x, increases. • For a medium of constant cross sectional area, A, con¬stant soil porosity, a, a constant mass of injected tracer, M, and a fixed distance of travel, x, Cmax will decrease as D/va increases. Klotz and Moser (1974) concluded that D is about proportional to no.3 where r) is the kinematic viscosity; D is about proportional to a-3 where a is soil porosity; D in¬creases with increasing grain size; D increases as grains become less spherical; D increases with greater grain rough¬ness and angularity; D increases with increasing uniformity coefficient; and D is significantly affected by grain size and uniformity coefficient. The remaining parameters are not significant. Numerical Simulation Studies Numerical simulation studies were used to investigate the nature of flow and the optimum length of a toxic package within a saturated porous medium of fixed dimensions and configuration (Fig. 1). The width and position of the package was maintained constant (Phelps et al., 1981). Results indicate that if the package extends throughout the length of the model, the flow is vertically downward and

Jan 1, 1984

By d&apos, John C. Entremont

Pure iron was inductively melted in small refractory crucibles and optical pyrometer and immersion thermocouple readings were simultmzeously taken. The resulting emissivities of the liquid iron surface obtained were found to be greatly affected by both the gaseous atmosphere and geometrical changes in the physical setup. Quantitative values for these effects are indicated. FOR many applications in both the laboratory and plant, optical pyrometry is still the best means of measuring temperatures in the incandescent range. A prerequisite in evaluating the correct temperature is a good value of the emissivity of the surface. To obtain the emissivity from the tabulated values of the literature can be very confusing and often far from correct. There are many reasons for these difficulties, and it is not within the scope of this paper either to enumerate or to discuss them all. Its purpose is to show quantitatively how several factors affect the apparent emissivities obtained from experimental measurements on liquid iron surfaces. The black body is the reference state for the quantitative values of emissivities and is defined1 as a body which absorbs all radiation incident on it, reflecting none; such a surface emits more radiation per unit area per unit time than any surface which reflects any radiation, and is given a value of unit emissivity. All bodies having reflective power thus have emissivities less than unity and are considered nonblack or grey bodies. The ratio of the radiant energy emitted by the flat, nonblack surface to that of a perfectly black surface of equal area and temperature is the emissivity of the surface. The above definitions are applied to flat, polished, opaque surfaces, very seldom encountered in actual measurements, and for this reason many authors have suggested that the word "emittance" be used for real bodies rather than emissivity. The emittance has reference to the material and its configuration rather than to its properties in the idealized state. Recent observations of molten iron in a small refractory crucible indicate that not only the configuration of its surface but the geometrical arrangement of its surrounding and the nature of the surrounding atmosphere have a pronounced effect on the emittance. Neglect of changes in such conditions may lead to errors as large as 40°C at 1600°C. Thus it is suggested that the term "apparent emissivity" be used and that it be recognized that its value pertains to a particular experimental arrangement only. As a result of not recognizing these differences in emissivities, which are obtainable from changes in the physical setup of an observation, many investigators have incorrectly quoted their values as those of the emissivities of particular materials rather than as an apparent emissivity for their particular arrangements. As a consequence, values of the emissivity of liquid iron ranging from 0.3 up to 0.55 are found in the literature. In an effort to establish an accurate optical temperature scale for liquid iron solutions in which de-oxidation studies were to be carried out, it was observed that the temperature relationship, obtained by simultaneously taking immersion thermocouple

Jan 1, 1963

By D. V. Carter, Dan C. Williams, John R. Coombs

Exploration was active in East and East Central Texas during 1944. Ten oil fields were discovered during the year, of which four show promise of development. The discovery wells of the Sand Flat and Tyler, South fields were drilled to a depth greater than 10,000 ft., and the latter field now produces from the Pettit at a depth of 9890 ft. The Sand Flat well was plugged back to the Paluxy. The other two fields are Glen Rose producers near 8000 ft. The Pickton field produces from the Bacon Lime and Winnsboro from the Rodessa section. The Eylau field, Bowie County, was significant as the first Smackover production in Texas. Magnolia drilled a test in the Concord field, which topped salt. The most extensive and significant development in the district was the Carthage gas-condensate field. It expanded from the 8000 acres of last year to an estimated 190,000 acres, or about 300 sq. miles, and is not defined as yet. The first oil production in the Carthage area was made from the Travis Peak in 1944 in the Rogers Lacy&apos;s Cameron Lumber Company well No. I, on the northwestern side of the field. The New Hope field, Franklin County, scored the largest number of completions during 1944 with 24, bringing its total number of wells to 27. Two more pays were opened and produced as dual completions with the older horizons. The Manziel field, Wood County, had 19 new wells added during the year, for a total of 29, while the Pittsburgh field, Camp County, reached a total of 23 wells by completing 14 new ones. Material shortages and drilling restrictions dropped the total number of producing wells completed in the district from 171 during 1943 to 141 for 1944. Abandonments increased from 531 during 1943 to 609 for 1944. Of this number, 479 were in the East Texas field. Subsidy payments had very little effect in the district and it was mostly a few of the old fault-line fields that had any wells to fall within the requirements for subsidy payments. The prices of crude oil remained constant in the district except for increases as a result of subsidy payments. Production and Probation Wartime demands called for increased allowables for many fields, consequently the condensate and oil production for 1944 increased to 190,016,180, which is up 6.9 per cent over 1943. The East Texas field, of course, remained the principal producer of the district, accounting for 134,768&apos;499 bbl. during the year, or 71 per cent of the district total production of condensate and oil. The field topped its own 1943 production by 4.8 per cent and became the first field in the world to produce 2 billion barrels of oil. The Hawkins field remained the second largest oil producer in the district, with 13,317,088 bbl. for the year, a drop of 6.8 per cent from 1943, while Van field was third with 11,635,708 bbl. The

Jan 1, 1945

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By E. S. Lenker, H. J. Van Hook

A complete swies of solid solutions has been found between the compounds InAs and GaAs Below the solidus. The melting relations determined by differential thermal and static quenching technzques, indicate that the liquidus and solidus are of the simple ascendant type. No evidence of unmixing of the homogeneous solid solutions was observed at sub-solidus temperatures. A quenching method for locnting the solidus, using X-ray diffraction techniques, is described in some detail. THE semi-conducting properties of compounds formed by various combinations of the less familiar intermetallic elements have created an increasing interest in the phase relations in systems involving these elements. The complete phase diagram of such a system, containing a compound of special interest, will often provide information as to the most favorable conditions for preparing large crystals from a melt, as well as specifying the temperature stability of the crystalline phase or phases produced. In view of the current importance of gallium arsenide in semiconductor research and of the structural similarities of indium arsenide, it was thought that the complete phase relations of the system InAs-GaAs should be investigated. Previous work on the system Ga-As by Koster and homa&apos; and on In-As by Liu and peretti2 has shown that GaAs and InAs are the only compounds formed, having melting points of 1238° and 942°C, respectively. In a survey of various systems of elements from groups IIIb and Vb, spengler3 also re- Mines Ltd., for his continuing encouragement and for permission to publish the results of this work. ports complete miscibility of gallium, indium, and arsenic in the liquid state. In a partial investigation of the InAs-GaAs system, Woolley and smith4 found extensive solid solution throughout the alloy range. Their subsolidus work, however, was inconclusive at temperatures below 900" and they did not determine the liquidus relationships of the system. PRESENT INVESTIGATION The starting materials used were high-purity gallium, indium, and arsenic. The method of preparation of the compounds follows that devised by M. Shafer and is described in detail in a paper by Shafer and eiser.&apos; The end-member compounds, GaAs and InAs, were first prepared by reaction of the elements in the desired proportions in evacuated silica glass vials. The vials were rotated in a furnace as the temperature was slowly raised to insure rapid and complete reaction at low temperatures. Thereafter the starting materials, GaAs and InAs, were melted by heating the sealed vials to 1300" and 1000°C, respectively; the vials in this case were filled as completely as possible to keep the vapor space small and thereby minimize the loss of arsenic to the vapor phase. Ten binary mixtures of these compounds were then prepared by reaction of the powdered material in the solid state just below solidus temperatures. At 900C preparations containing 3, 5, 8, 10, 25, 35, 50, and 75 mol pct GaAs were found to be single homogeneous phases, indicating a complete series of solid solutions between GaAs and InAs. Moreover, it was discovered that the homogeneity of any crystalline binary preparation could be very accurately checked by X-ray diffraction because of the large differences in unit cell dimensions of the end membe5s. The cubic lattice constant ofor GaAs is a = 5.652A and that of InAs is a = 6.061A

Jan 1, 1963

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By Tracy L. Atherton

THE mapping of slant-hole oil fields is complicated by the fact that relationships between wells are subject to variations in three dimensions and are not readily adaptable to representation on a plane surface. Formalized perspectives usually expand into an undecipherable maze of lines and peg models with the necessary supporting dividers serve only to awe the beholder with their perplexity. The usual compromise arrived at is a plotting of the projection of the courses of all of the wells in the field onto a horizontal plane (Fig. I). These complicated plots, when used in conjunction with the individual vertical projections of the wells, heretofore have been the most practical foundation for the study of general field problems. This method has many shortcomings, however, which are not found in the recently developed straight-hole equivalent projection method. The new method supplies a series of maps similar to the type now in common use in straight-hole fields. It is remarkably simple to use and supplies a ready check on clearances between wells. Perhaps the method can best be understood if the steps that led to its development are described. Common practice of oil-well surveyors is to supply the owner with a tabling of the survey and a plan view plotted against the true meridian. If a vertical projection is plotted, it is usually plotted separately and shows vertical depths against the projection of the stations along a section line joining the top and bottom of the hole on the plan view. A more practical method would be to plot the section line of the plan parallel to the abscissa of the vertical projection (Fig. 2). If this is done, any line parallel to the "base line" will pass through the points on each projection that represent a single point in the hole. Another very useful graph, which the well surveyor could provide, would be plotting of vertical depths against measured depths. Fig. 3 illustrates the next step facilitated by this form of plotting. The lines designated "well A" represent the proposed course of a hole to be drilled. Superimposed on the drawing, in its proper relative position, is the plan view and a portion of the vertical projection of a present producer, "well B." From an inspection of the plan view we arrive at the correct conclusion that the only indicated possibility of collision is at the point of crossing of the wells on the plan view. Referring to the vertical projection, note that the vertical depths of stations on B, in the vicinity of the crossing, are plotted on the same plane of projection as A. The clearance is the indicated distance between the two vertical sections measured along the parallel to the "base line," which passes through the point of intersection of the plan view. Repeat this process for the other wells crossing the proposed course of A on the plan view and you have a preliminary check of clearance for the proposed course. A similar comparison of crossings on the vertical projections of all

Jan 1, 1941

By J. Offeringa, C. van der Poel

The report describes scaled model experiments on the recovery of oil from porous sands by the injection of miscible liquids [solvents] and the subsequent recovery of the solvents by water flooding. Special attention has been paid to the scaling problem. Scaling rules are deduced and their correctness is checked by carrying out experiments in tubes of various sizes. Data are submitted on the effect of the viscosity ratio oil-solvent on the efficiency of the displacement process, the viscosity ratio varying from 1.5 to 5,000. Breakthrough recoveries obtained when flooding with kerosene as a solvent, are equal to those obtained in water flooding at the same viscosity ratio, indicating that he phenomenon of viscous fingering is decisive. After breakthrough, however, flooding with a miscible liquid becomes much more efficient than a water flood and this is more pronounced as the viscosity ratio oil-solvent is higher. Although high oil recoveries are obtained and most of the solvent in the sand can be recovered by a subsequent waterdrive, a straight flood with miscible liquids does not appear economically attractive because of the large quantities of solvent required. Therefore, a circulation process is introduced, the features of which are described in this paper. Though by means of this circulation process the amount of solvent required can be drastically reduced, the process is not yet economic. SCOPE OF THE INVESTIGATION The recovery efficiency by water flood of oils of viscosities exceeding 50 cp is low. As interest in production of these highly viscous oils is growing at the moment, it was considered worthwhile to gain basic information on the feasibility of first flooding such oils with a low viscous miscible liquid [solvent] and subsequently producing the latter in a conventional way, e.g. by water flooding. The method has the obvious drawbacks that return on the investment is delayed until water flooding has begun and that it requires the investment of a more valuable product to produce a less valuable one. On the other hand, it may be expected that the displacement of one liquid by another is more efficient when the two liquids are miscible than when they are immiscible. As laboratory data on this point are scanty, the present investigation seemed justified. Another argument for carrying out these experiments is that they present a valuable contribution to our concepts of the scaling problem in reservoir engineering studies. Some major difficulties which are encountered in the scaling of the waterflooding process such as the scaling of the capillary forces and the difficulty of obtaining the same permeability characteristics in the model do not present themselves in this case. As the fluids are miscible capillary forces do not play a role and as there is only one fluid phase, Darcy&apos;s law is valid in its original form. Consequently it is felt that the scaling rules can be deduced with a greater amount of certainty. An essential feature of the experiments is that they are scaled model ones, which are, however, somewhat

Jan 1, 1955

By R. A. Bell, R. Schultz, P. G. Hallof

The Ballyvergin area is located in County Clare on the southwest coast of Ireland. It is one of six areas in County Clare in which mining operations were carried out during the last century. The ores mined were high grade Cu-Pb-Ag deposits in the form of small fracture fillings and gash veins in the lower Carboniferous limestones. The zone of primary economic interest is situated on the north limb of a geosyncline which plunges moderately to the southwest. The zones of mineralization previously mined were associated with local structures and folds, and the initial geophysical investigations took the form of reconnaissance induced polarization measurements around, and between, the old mines. This work located an anomaly which, on drilling, resulted in a small extension of the Pb-Cu ore at the Ballyvergin mine. However, a potentially more important zone of mineralization resulted from the drilling of another IP anomaly near Ballyvergin. This wide anomaly was found to be a domal shaped deposit of disseminated chalcopyrite located at a depth of more than 100 ft. The deposit is controlled by local folding in the sediments and is of a type previously unknown in the area. More IP investigations are under way to locate other deposits of the same type. The Ballyvergin area is located in County Clare, about 35 miles northeast of Shannon Airport, near the Atlantic west coast of Southern Ireland (Fig. 1). Interest in the area stems from a number of occurrences of small, but high grade, Pb-Ag deposits. From the summer of 1960 to the spring of 1961, Irish Base Metals carried out a comprehensive exploration program on a 38-sq mile concession in east-central County Clare in an attempt to locate additional deposits of this type. Field operations consisted of geologic mapping, geochemical soil and stream sampling, geophysical surveying and diamond drilling. The geophysical program consisted primarily of detailed induced polarization (IP) surveys in the general vicinity of old mine workings, supplemented by electromagnetic and self-potential investigations. Subsequent diamond drilling of a well defined IP anomaly close to the old Ballyvergin mine disclosed a sizeable deposit of low grade disseminated copper, a type of deposit previously unknown in this area. REGIONAL GEOLOGY Topography: The topography is of the Karst type with low regional relief. The northern parts of the area are covered almost completely with glacial deposits including a large number of drumlins. Elsewhere the overburden is patchy and only moderately deep. A close network of roads makes every part of the area readily accessible, and rail and harbor facilities are available nearby — Fig. 2. Stratigraphy: The area was mapped on a reconnaissance basis by the Geological Survey of Ireland during the latter part of the 19th century at scales of 1 and 6 in. to the mile. Mapping is complicated in

Jan 1, 1962

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

In the 100&apos; years since AIME was founded in 1871, the Institute has issued a great many publications in a variety of forms: periodicals, Transactions volumes, and special volumes or books. The following is a brief history of AIME publishing with some suggestions for proper referencing. TRANSACTIONS AIME Transactions volumes have been numbered consecutively since No. 1 was issued in 1873, including papers for the period 1871-1873. One or more volumes have been issued each year and may be divided into three general time periods: General Volumes (1873-1927), Volumes classified by subject matter (1928-1949), and the present practice, begun in 1949, of issuing three volumes per year, one each in the fields of mining engineering, metallurgy, and petroleum technology. The broad divisions of subject matter in each of these volumes correspond to the technical areas of the three constituent societies of AIME. AIME&apos;s Technical Publications, usually designated by TP number&apos;s (until the change in numbering system by the Society of Mining Engineers in 1958), may, with some exceptions, be referenced to an AIME Transactions volume. Reference to a specific volume, rather than paper number, is the preferred reference, since the volumes are the form of publication most commonly available in libraries. In many cases, over the years, the Technical Publications may also have been available in some other form, either as separates or in a periodical. General. Volumes (Vols. 1-78, 1873-1927): Until 1927 all papers eligible for Transactions were published in general volumes with no systematic attempt made to segregate the material on the basis of the technological fields to which the papers related.. One volume per year was issued from 1873 until 1912; from 1912 until 1927 from two to four volumes were issued annually. In addition to the Transactions papers, these volumes carried some of the proceedings of the business meetings of AIMS. Subject Volumes. (Vols. 79-183; 1928-1949): The material for these volumes was segregated according to subject matter, and up. to seven volumes were issued a year. In the latter part of the period, from 1934 on, there was one volume each&apos; year for the Petroleum, Institute of Metals, and Iron and Steel Divisions and-the remaining papers were grouped in various ways and is sued whenever sufficient numbers of papers had accumulated: The subject volumes containing mining engineering papers are listed in Table 1. The volumes for the period, 1936-1949 are included in this Cumulative Index. Each of the Transactions volumes carries on the binding the year of publication; this date does not give an indication of when the papers included were originally presented at meetings. The contents of the volumes usually list the meetings at which. the papers were presented. Not all papers from a given meeting necessarily are in one Transactions volume. Some of the earlier volumes do not have a number on the binding or within the volume. In 1934 numbers" were assigned to all Transactions volumes, commencing with the 1871-1873 volume as No. 1. Many of the papers published [ ]

Jan 1, 1972

By R. M. Brick, R. G. Treuting

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By James H. Boettcher

INTRODUCTION There are many and varied sources of finance available to the mining industry for exploration, development and/or the operation of mining projects and companies. These sources include equity from major as well as "penny" stock exchanges, precious metal mutual funds, private investor groups (from "grubstakes" to tax-oriented limited partnerships) and banks. The variety is representative of the fact that the world&apos;s capital markets are segmented and stratified according to risk-reward characteristics. This interrelationship is summarized in Exhibit I and 2 which relate (very approximately) various sources of finance to a typical mining project&apos;s life cycle and risk-return characteristics. The objective of this paper is to introduce, as it applies to the mining industry, a somewhat recent phenomenon represented by one of these capital markets segments referred to as "venture capital." Venture capital investing per se, which today is a multibillion dollars per annum investment business, goes back as far as Queen Isabela&apos;s backing of Columbus&apos; "wild ideas." The real institutionalization of the venture capital process really began in earnest, however, after World War II. Today over 700 private venture capital sources (and more government related ones) exist providing funding to a range of industries, but typically related to the "high-tech" business. The table to the right shows industries financed by venture capital funds between 1980 and 1982. Conspicuous by its absence is, of course, mining which is not a great surprise since typical mining projects up until recently were large, required long lead times and were undertaken by established mining houses. Also, as most of you can appreciate, successful investing in the mining business requires a great deal of experience and understanding of the industry which most venture capital funds do not have. TARGETED RETURN The rate of return objective of most venture capital funds is, according to the legalized version, to realize a return which is "substantially in excess of that obtainable through conventional equity investments." One may say that a common objective of venture capital funds is to realize a 20% to 30% compound annual internal rate of return on capital over their life which is often ten years. [ ] This objective has been recently more feasible in the mining sector due to the development of smaller precious metal projects which cost less and are quicker to generate cash flow than the behemoth projects of the 1970s. In addition to precious metals, venture capitalists have invested or looked at a variety of other mining projects including ones as prosaic as a high margin "kitty litter" operation, sand-gravel and other industrial minerals operations, the leveraged buyouts of coal mines or mineral divisions of major energy or mining corporations, and even in in-situ copper or gold leaching ventures. A typical investment is in the range of $100,000 to $3,000,000 although some can go as high as 5,000,000. This implies a project size up to, say, 30,000,000 if a venture capital fund does it on its own. Larger projects can be done if the equity portion of the investment is syndicated with other investors.

Jan 1, 1985

By N. A. D. Parlee, E. M. Sacris

OVER 55 years ago, Sieverts and Hagenacker1 and Donnan and shaw2 made determinations of the solubility of oxygen in liquid silver, over a rather short range of temperatures (973° to 1125°C), using quartz bulbs, mainly at 1 atm. From the results of their investigations, Mizikar, Grace, and parlee3 plotted % O vs 1/T and obtained the following straight-line equation for solubility at 1 atm: log % O = 723.7/T - 1.0949 Recent work on the kinetics of the Ag-O2 system394 indicated there might have been some error due to reaction with the direct heated silica bulbs. Thus it became important to redetermine the solubility with the silver contained in a better refractory such as alumina, and by induction heating where the walls of the container were not so strongly heated. It was also desirable to extend the temperature range. A modified Sieverts apparatus of fairly standard type was used except that a special type of reaction tube was employed, Fig. 1. Dried argon with a guaranteed purity of 99.9 pet, and dried medical-grade oxygen with a guaranteed purity of 99.6 pet containing a little nitrogen, were the gases used. The measuring system consisted essentially of a manometer and a water-jacketed 100-cc gas buret with an open-end vertical tube parallel to the buret. This tube has the same diameter as the buret in order to give the same capillary effect on the mercury. A screw leveling device was used with the buret leveling bulb to help provide accurate pressure readings. A 2-mm ID capillary line connected the buret to the reaction chamber, helping to reduce the dead volume, which was determined with argon. The heating medium was a 2.5-kw output induction furnace. The induction coil was made of a 3/16-in. copper tubing with eight turns and an inside diameter of 4 cm. The reaction bulb was made of a quartz tube 18 cm long and 3 cm in inside diameter, Fig. 1. Inside the quartz tube were two alumina crucibles (Mor-ganite Triangle RR, XN10 and XN5) one inside the other. Below these two was an alumina disk. The disk prevented the corners of the outer crucible from expanding against the quartz tube. The solid sample (99.994 + pet Ag), which had been previously cleaned by air oxidation and repeated removal of scum, was placed inside the inner crucible. An alumina disk with a hole at the center covered the two crucibles. In order to decrease the dead volume, an evacuated quartz "filler" tube was placed on top of the crucible cover. The part of the reaction tube above the spherical joint was made up of Pyrex glass with a flat glass top. It was here that a prism was placed to facilitate the use of an optical pyrometer, previously calibrated at the freezing point of silver. This type of reaction bulb and furnace assembly was specially designed for this work, and used in preference to the relatively new water-

Jan 1, 1965